sv8300 - sip trunking, ip ccis, ip phones

[cayres1003]

hello everyone,
I am looking for some information. Anybody have a setup with multiple locations using sv8300s where there are Sip trunks from a provider being used for inbound and outbound dialing and where they have ip ccis working and Ip phones at one or more of these locations; working in every way. trunks, ext to ext dialing, ip phones, all connected in a network and working

thanks

 

[mahirgul]

Three location CCIS Sample:
TS:
PBX1;PC=1,IPaddress 10.10.10.10; 1xxxx
PBX2C=2;IPaddress 10.10.20.10;21xx;22xx;23xx;24xx
PBX3;PC=3;IPaddress 10.10.30.10;25xx;26xx;27xx;28xx;29xx;30xx
All PBXs must use CCH=0
PBX1:
1002,000,D100,,Assign trunk nrs
1002,000,D100,,
1002,001,D101,,
1002,002,D102,,
1002,003,D103,,
1002,004,D104,,
1002,005,D105,,
1002,006,D106,,
1002,007,D107,,
1002,008,D108,,
1002,009,D109,,
1002,010,D110,,
1002,011,D111,,
1002,012,D112,,
3000,100,10,,Assign b-channels to route 10
3000,101,10,,
3000,102,10,,
3000,103,10,,
3000,104,10,,
3000,105,10,,
3000,106,10,,
3000,107,10,,
3000,108,10,,
3000,109,10,,
3000,110,10,,
3000,111,10,,
35000,10,04,,route 10 is tie line
35004,10,2,,route 10 has answer supervision
35009,10,03,,route 10 incoming signaling is wink start
35020,10,00,,route 10 outgoing signaling is wink start
35090,10,0,,route 10 is special route
35091,10,00,,route 10 uses CCH 00
A700,00,112,,assign CCH 00 to trunk 112
A701,00,00001,,originating point code
A80,00002,00,,assign all possible destinations of the CCH 00
A80,00003,00
A81,00002,010010020010,,IPaddress of oposite side for destination point code-example
A81,00003,010010030010
A726,00,0,,allow calling name display for CCH 00
A728,00,0,,allow call forwarding for CCH 00
A729,00,0,,allow multiple Call For
warding
A746,00,0,,point to multipoint CCIS
A710,00,14,,28 seconds between end dialing and alerting
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
For PBX 2 same scrip except :
A701,00,00002,,originating point code
A80,00001,00,,assign all possible destinations of the CCH 00
A80,00003,00
A81,00001,010010010010,,IPaddress of oposite side for destination point code-example
A81,00003,010010030010
>>>>>>>>>>>>>>>>>>>>>>
For PBX3 same scrip as for pBX1 except:
A701,00,00003,,originating point code
A80,00001,00,,assign all possible destinations of the CCH 00
A80,00002,00
A81,00001,010010010010,,IPaddress of oposite side for destination point code-example
A81,00002,010010020010
>>>>>>>>>>>>>>>>>>>>>>>>>>
LCCR PBX1:
857,2,04
857,3,04
200,2,A129
200,3,A129
8AA0000,3,4007
8A4007,21,0002
8A4007,22,0002
8A4007,23,0002
8A4007,24,0002
8A4007,25,0003
8A4007,26,0003
8A4007,27,0003
8A4007,28,0003
8A4007,29,0003
8A4007,30,0003
8A5002,167,002
8A5002,168,00002
5B01,00200,01010020010
8A5003,167,003
8A5003,168,00003
5B01,00300,010010030010
8A00002,1,00210
8A00003,1,00310
360,1010,0
>>>>>>>>>>>>>
LCCR PBX2:
857,2,04
857,3,04
857,1,04
200,2,A129
200,3,A129
200,1,A129
8AA000,3,4007
8A4007,21,8004
8A4007,22,8004
8A4007,23,8004
8A4007,24,8004
8A4007,25,0003
8A4007,26,0003
8A4007,27,0003
8
A4007,28,0003
8A4007,29,0003
8A4007,30,0003
8A4007,1,0001
8A5003,167,003
8A5003,168,00003
5B01,00300,01010030010
8A5001,167,001
8A5001,168,00001
5B01,00100,010010010010
8A0003,1,00310
8A0001,1,00110
360,1010,0
>>>>>>>>>>>>>>>>
LCCR PBX3
200,2,A129
200,1,A129
200,3,804
8AA000,3,4007
8A4007,25,8004
8A4007,26,8004
8A4007,27,8004
8A4007,28,8004
8A4007,29,8004
8A4007,30,8004
8A4007,21,0002
8A4007,22,0002
8A4007,23,0002
8A4007,24,0002
8A4007,1,0001
8A5002,167,002
8A5002,168,00002
5B01,00200,010010020010
8A5001,167,001
8A5001,168,00001
5B01,00100,010010010010
8A0001,1,00110
8A0002,1,00210
360,1010,0
>>>>>>>>>>>>>>

 

[mahirgul]

Multi location sip trunking is looking same but you must change a couple things.

 

[mahirgul]

For the sip trunking.

https://dl.dropboxusercontent.com/u/3188783/nec_sipunivergesv8300.pdf

https://dl.dropboxusercontent.com/u/3188783/31199-1-0--SV8300-SIPTrunking-Config-Skype.pdf