Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Superloop numbers and physical slots 1

Status
Not open for further replies.

Beattiejr

Technical User
May 26, 2005
10
SA
How do I relate superloop numbers to physical slots on an 81c?




 
group zero shelf one, counts left to right 2 units per slot, giving you slots 0 to 15, and 16 to 31 on shelf 1, the reason it gets a little fuzzy is a network card uses 4 time slots, if you have loop 0, 4, 8 and 12, that group could not have another card of any kind. but if you delete the left most card you could add dual pri's, 0, 1, 2 and 3.. if you go to load 22 and print cequ, you'll get some idea of your switch lay out. number of groups, a major concern. and slots you can actully add. if your not sure about ava space, post the cequ and one of us will explain how to trnaslate it

john poole
bellsouth business
columbia,sc
 
Thanks John. Here's the cequ.

[tt]cequ

mped 8d
term
remo
terd 001
remd
tero
remo
supl 004 016
supc
supf
ddcs 36
dtcs
xct 014 030 046 062
078 094
tds * 014 * 030 * 046 * 062
* 078 * 094
conf * 015 * 031 * 047 * 063
* 079 * 094
mfsd * 014 * 030 * 046 * 062
* 078 * 094
pri2 012 020 021 024
025 034 035 042
043 044 045 048
049 050 058 059
060 061 064 065
068 069 080 081
apvl
dti2 040 041
misp 28
ext0 3pe
cni 012 000 000
cni 012 001 001
cni 013 000 002
ext1 3pe
cni 012 000 000
cni 012 001 001
cni 013 000 002
mcfn s0b0 s0b1 s1b0 s1b1 s2b0 s2b1 s3b0 s3b1 flsh totl
016 000 016 000 016 000 000 000 032 080 [/tt]

I'm not sure how to reconcile the loops / slots with the physical location of the conf/tds cards, whose loop nos. I know and where I can see the physical card.

Any help would be appreciated.
 
your 1st card is the old loop 1 terd your supporting, the next card is a network card, has 2 places to plug a cable in the front, if your uising both, that gives you loop 4 0 and 4 1, if your using just j2, it's for 4 0. the next card looks like your pri card (loop 12) then your 1st conf/tds. . the next shelf, 0,1, starts with another network card, using post 16, because that is a network card it takes slots, 15,16,17, and 18. it's not a double wide card, but it takes 4 slots just the same, in load 97 (supl and xpe) the phyiscal location is defined as left or right hand side of those two slots. the next 4 cards i see are both dual pri, 20,21,24 and 25. i would have put those next to each other, and saved 24 for a possible network, the next card looks like a misp, (bti switching, vidio conf).. the last card in that shelf would be the confer/tds. that will give you a fair start, when i 1st started, i came in off hours and disl'ed loops and conf cards to locate the counts. it wasn't after an install that it made semse. remember, just to make it a liitle more fun, msdl cards can plug into any slot, now you have to tell software which network, but the device number is a switch setting only. don't let those confuse the issue, i usually build one loop on the right and the next on the right, leaving a otherwise unusable space in my shelf, the msdl only get power off of the backplane

john poole
bellsouth business
columbia,sc
 
here's your next loop

group 1 shelf 0

32
33

34 dual pri
35 dual pri

36 ddcs (which i've never seen)
37

38
39

40
41

42 dual pri
43 dual pri

44 dual pri
45 dual pri
[/quote}

i'm sure some one else can help.. each card slot on the 81 has two addresses, starting with 0,1. count down to the left, like i mentioned, once you get a few labels on then disl a pri or two, off hours to get a complete picture. i'm guessing you work in a call center, or gov site, no one else could afford that many trunks for so few phones

john poole
bellsouth business
columbia,sc
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top