Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Sunblade 150 NVRAM IDPROM Reprogramming Issues

Status
Not open for further replies.

DTGMI

Vendor
Jun 1, 2006
236
US
Just a quick question ...

We have reprogrammed the IDPROM NVRAM on older ULTRA and SB100s - probably running on OpenBoot 3.x and the mkp command always worked easily to reset the ethernet and host ID - SN

We just replaced the battery on a Sunblade 150 and am trying to reprogram the IDPROM

In the past we just ran these basic commands w/ the applicable ETH and Serial # data added.

Problem is that the mkp command returns a - mkp ?? result as it doesn't recognize the command?

Is it an OpenBoot version issue? This SB150 is running on OB 4.6 I believe

1 0 mkp
83 1 mkp
8 2 mkp
0 3 mkp
20 4 mkp
c0 5 mkp
ff 6 mkp
ee 7 mkp
0 8 mkp
0 9 mkp
0 a mkp
0 b mkp
c0 c mkp
ff d mkp
ee e mkp
0 f 0 do i idprom@ xor loop f mkp



 
LOL I just encountered the same issue today, hope someone can help.
I was thinking about firing up one of my old sparc20 or ultra10 and reprogram a new nvram to the blade 83 ID
and then swap it into the blade. ST micro makes new chips that need to be programmed . they are less than $20
M48T58Y-70PC1 I ordered one and am waiting for it to try...
 
Chuck

That's what we ended up doing to get our SB150 running.

Bought some new NVRAM chips ... put them into one of our lab Ultra 5s and reprogrammed it with the correct Sn etc per instructions and then put it in the SB150.

Came right up.
 
oh also i noticed there is a 3 volt lithium battery on the blade motherboard.
thought the battery was encased in the nvram like older suns.
any idea what this battery is for?
 
where did you buy new chip from and part# ?
the original nvram is M48T59Y-70PC1 these are obsolete and any out there are probably old with dead battery.
I bought a new M48T58Y-70PC1 which is still in production - configured it in ultra 10 ( 80 ID )with mkp and worked fine.
Then reconfigured it for blade ( 83 ID ) and transfered chip to blade - shows banner ok and starts booting
hard drive and stops and says " can't load TOD program terminated " I assume means time of day
Boots ok with another good nvram I have
Am i missing something or will these M48T58Y not work in a blade ??
 
@chuck57: Did you resolve this issue (with M48T58Y not working in a Blade) and if so, what did you do? I have just experienced exactly the same problem.
 
I ended up purchasing some 59's on ebay that came from china - only like $8 , 2 of the 3 actually worked -
programmed them in ultra10 and then installed chip in blade.
There are also US vendors that sell what they claim are new ones for the blade and they are like $50
Bought one of these and it also worked
 
I was hoping that you had found a work-around. It seems that the kernel halts when it tries to load
the driver for the TOD-chip, which would indicate that it is using some of the registers available on
the 59, but not on the 58. AFAIK Solaris is not using this functionality, but I could be wrong. Patching
the driver would be ideal, but probably not worth the effort. I tried starting the kernel i debug-mode,
but it appears to halt before it comes that far.

The problem with the 59's currently on sale is that, AFAIK, they are all refurbished.
 
I can add that the 58 apparently works fine on an Ultra 10, presumably all non-Blade sun4u's.
 
I am needing to replace the nvram on a sunblade 150. I noticed this thread. Any recommendations on where to get a replacement and do they work as shipped or is reprogramming necessary? If programming is necessary, how is that accomplished?
Thanks to all who respond...
 
I can't recommend any of the suppliers as the ones I've got have all been depleted. Some supplierson net are selling them as new, but they have not been manufactured for years AFAIK. I never got a response from these suppliers and ended up buying some from e-bay and attaching a CR-2032 socket and battery externally. As for reprogramming, see e.g.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top