I have two T2000 servers connected to sun storage array StorEdge 3310 as follows:
CH0 connected to SNGL BUS CONF
CH1 connected to HOST1
CH2 open
CH3 connected to HOST2
DUAL BUS CONF open
I have created some luns which I can mount and use on HOST1 but from HOST2 I cant see them
from OK prompt or from format utility. I do see them from sccli utility on HOST2 .
iam runnng solaris 10u11 with latest patches applied and both systems are identical.
the channel assignment on the storage array is as follows :
Chl Mode PID SID
0 Drive 6 7
1 Host 0 NA
2 Drive 6 7
3 Host 0 NA
6(c) RCCOM NA NA
this is what i get on HOST1
---------------------------
scsi-initiator-id 5 (value) 7 (default)
ok probe-scsi-all
/pci@7c0/pci@0/pci@8/pci@0/LSILogic,scsi@8,1
MPT Version 1.02, Firmware Version 1.03.39.00
Initiator ID is 7
/pci@7c0/pci@0/pci@8/pci@0/LSILogic,scsi@8
MPT Version 1.02, Firmware Version 1.03.39.00
Initiator ID is 7
Target 0
Unit 0 Disk SUN StorEdge 3310 423C 635406336 Blocks, 325 GB
Unit 1 Disk SUN StorEdge 3310 423C 364544000 Blocks, 186 GB
Unit 2 Disk SUN StorEdge 3310 423C 142850560 Blocks, 73 GB
this is what i get on HOST2
---------------------------
scsi-initiator-id 4 (value) 7 (default)
ok probe-scsi-all
/pci@7c0/pci@0/pci@8/pci@0/LSILogic,scsi@8,1
MPT Version 1.02, Firmware Version 1.03.39.00
Initiator ID is 7
/pci@7c0/pci@0/pci@8/pci@0/LSILogic,scsi@8
MPT Version 1.02, Firmware Version 1.03.39.00
Initiator ID is 7
Target 0
Unit 0 Device type d SUN StorEdge 3310 423C <<< why iam getting a host here instead of disks?
CH0 connected to SNGL BUS CONF
CH1 connected to HOST1
CH2 open
CH3 connected to HOST2
DUAL BUS CONF open
I have created some luns which I can mount and use on HOST1 but from HOST2 I cant see them
from OK prompt or from format utility. I do see them from sccli utility on HOST2 .
iam runnng solaris 10u11 with latest patches applied and both systems are identical.
the channel assignment on the storage array is as follows :
Chl Mode PID SID
0 Drive 6 7
1 Host 0 NA
2 Drive 6 7
3 Host 0 NA
6(c) RCCOM NA NA
this is what i get on HOST1
---------------------------
scsi-initiator-id 5 (value) 7 (default)
ok probe-scsi-all
/pci@7c0/pci@0/pci@8/pci@0/LSILogic,scsi@8,1
MPT Version 1.02, Firmware Version 1.03.39.00
Initiator ID is 7
/pci@7c0/pci@0/pci@8/pci@0/LSILogic,scsi@8
MPT Version 1.02, Firmware Version 1.03.39.00
Initiator ID is 7
Target 0
Unit 0 Disk SUN StorEdge 3310 423C 635406336 Blocks, 325 GB
Unit 1 Disk SUN StorEdge 3310 423C 364544000 Blocks, 186 GB
Unit 2 Disk SUN StorEdge 3310 423C 142850560 Blocks, 73 GB
this is what i get on HOST2
---------------------------
scsi-initiator-id 4 (value) 7 (default)
ok probe-scsi-all
/pci@7c0/pci@0/pci@8/pci@0/LSILogic,scsi@8,1
MPT Version 1.02, Firmware Version 1.03.39.00
Initiator ID is 7
/pci@7c0/pci@0/pci@8/pci@0/LSILogic,scsi@8
MPT Version 1.02, Firmware Version 1.03.39.00
Initiator ID is 7
Target 0
Unit 0 Device type d SUN StorEdge 3310 423C <<< why iam getting a host here instead of disks?