Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chris Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Speed Dial
- Thread starter edkender
- Start date
MitelInMyBlood
Technical User
Not to my knowledge.
Original MUG/NAMU Charter Member
Original MUG/NAMU Charter Member
MitelInMyBlood
Technical User
Interesting. Can you explain a little more or perhaps give us an example? This (like many other things) wasn't discussed in CVOICE (or CIPT) classes. Of course there's only a week's time to cover 4 weeks of material 
Thanks!!
Original MUG/NAMU Charter Member
Thanks!!
Original MUG/NAMU Charter Member
you will need an access code since XXXX can be anything within a NPA-NXX area, or almost anything.
In this example 9 is for outside calls and let's say internal DN's are in the 5XXXX and 6XXXX range. So 8 can do or anything for that matter. * or # would work but let's go with 8.
User will dial 8XXXX where the XXXX is the last 4 digits of the LD number you are trying to dial.
That will hit a translation pattern the will strip the 8 and add the 9.1xxx-xxx in front of the XXXX making a LD call.
That will match a route pattern and send the call out the appropriate gateway.
Yes they will need to dial 5 digits, but if they don't want to dial 12, 5 is much better.
In this example 9 is for outside calls and let's say internal DN's are in the 5XXXX and 6XXXX range. So 8 can do or anything for that matter. * or # would work but let's go with 8.
User will dial 8XXXX where the XXXX is the last 4 digits of the LD number you are trying to dial.
That will hit a translation pattern the will strip the 8 and add the 9.1xxx-xxx in front of the XXXX making a LD call.
That will match a route pattern and send the call out the appropriate gateway.
Yes they will need to dial 5 digits, but if they don't want to dial 12, 5 is much better.
CUCM 9 now has this functionality!
Versions prior to 9, not so much. Props to whykap for a creative pre9 workaround. I also have used a TCL script on the gateway to add digits to the end of a dial string successfully, for long distance codes or pager return digits. It wasn't easily scalable but it works great. Upgrade to 9 if you can.
Thanks
TZ
Versions prior to 9, not so much. Props to whykap for a creative pre9 workaround. I also have used a TCL script on the gateway to add digits to the end of a dial string successfully, for long distance codes or pager return digits. It wasn't easily scalable but it works great. Upgrade to 9 if you can.
Thanks
TZ
gnrslash4life
MIS
If you're referring to abbreviated speed dials, they have been around. Not new for 9.x
Just set up your existing speed dial to send out the first 6 digits, then manually type in the last 4.
ie set up 91212555 then add in 1212 manually. You may have to test the timing on it to know when to enter the digits.
You may also need to set up translation pattern in your partition to open a line after the abbreviated dial so the system does not time out/error on the fact that you have dialed too few digits.
ie set up 91212555 then add in 1212 manually. You may have to test the timing on it to know when to enter the digits.
You may also need to set up translation pattern in your partition to open a line after the abbreviated dial so the system does not time out/error on the fact that you have dialed too few digits.
- Status
Similar threads