Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations SkipVought on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Site 2 Site VPN (Dynamic IP on one end)

Status
Not open for further replies.
maynarja

maynarja

MIS
Jan 24, 2007
41
0
0
CA
I cannot get the site to come up. I do believe that I should be using a dynamic map but I also tried and it fails as well. It looks like it fails within phase 1.

Remote A - internal net - 172.16.0.0/20 and 10.0.3.0/24
Remote B - internal net - 192.168.12.0/24

I also have set both sides to aggressive mode.

Can someone show me a proper config with the informations below?

##########
Remote A
##########

isakmp enable outside
isakmp identity auto
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption aes
isakmp policy 10 hash sha
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400

access-list outside_cryptomap_20 permit ip 10.0.3.0 255.255.255.0 192.168.12.0 255.255.255.0
access-list outside_cryptomap_20 permit ip 172.16.0.0 255.255.240.0 192.168.12.0 255.255.255.0

crypto ipsec transform-set Site2Site esp-3des esp-sha-hmac

crypto map StaticMap 20 match address outside_cryptomap_20
crypto map StaticMap 20 set peer 0.0.0.0 [Not sure as I do not see this in the config after I enter it]
crypto map StaticMap 20 set transform-set Site2Site
isakmp key presharekey 0.0.0.0 netmask 0.0.0.0 no-xauth

crypto map StaticMap interface outside

access-list nonat extended permit ip 10.0.3.0 255.255.255.0 192.168.12.0 255.255.255.0
access-list nonat extended permit ip 172.16.0.0 255.255.240.0 192.168.12.0 255.255.255.0
nat (inside) 0 access-list nonat

#########
REMOTE B
#########

isakmp enable outside
isakmp identity auto
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption aes
isakmp policy 10 hash sha
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400

access-list outside_cryptomap_20 permit ip 192.168.12.0 255.255.255.0 10.0.3.0 255.255.255.0
access-list outside_cryptomap_20 permit ip 192.168.12.0 255.255.255.0 172.16.0.0 255.255.240.0


crypto ipsec transform-set Site2Site esp-3des esp-sha-hmac

crypto map StaticMap 20 match address outside_cryptomap_20
crypto map StaticMap 20 set peer XXX.XXX.XXX.XXX
crypto map StaticMap 20 set transform-set Site2Site
isakmp key presharekey address XXX.XXX.XXX.XXX netmask 255.255.255.255 no-xauth


crypto map StaticMap interface outside

access-list nonat extended permit ip 192.168.12.0 255.255.255.0 10.0.3.0 255.255.255.0
access-list nonat extended permit ip 192.168.12.0 255.255.255.0 172.16.0.0 255.255.240.0
nat (inside) 0 access-list nonat
 
Sort by date Sort by votes
Make sure the following lines reference the IP addresses of the opposite site. Dont need Dynamic maps for site to site.

REMOTE A:

crypto map StaticMap 20 set peer REMOTE-B-OUTISDEINTIP
crypto map StaticMap 20 set transform-set Site2Site
isakmp key presharekey address REMOTE-B-OUTISDEINTIP netmask 255.255.255.255 no-xauth


REMOTEB:

crypto map StaticMap 20 set peer REMOTE-A-OUTISDEINTIP
crypto map StaticMap 20 set transform-set Site2Site
isakmp key presharekey address REMOTE-A-OUTISDEINTIP netmask 255.255.255.255 no-xauth

Free Firewall/Network/Systems Support-
 
Upvote 0 Downvote
Sorry --

Remote A = Static External IP

Remote B = Dynamic External IP

 
Upvote 0 Downvote
I have tried that site as well.

It have even tried setting both as static for a bit and still cannot get past Phase 1.

Here are the configs

#########
REMOTE A
#########
isakmp enable outside
isakmp identity auto
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption aes
isakmp policy 10 hash sha
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400

access-list outside_cryptomap_20 permit ip 192.168.12.0 255.255.255.0 10.0.3.0 255.255.255.0
access-list outside_cryptomap_20 permit ip 192.168.12.0 255.255.255.0 172.16.0.0 255.255.240.0


crypto ipsec transform-set Site2Site esp-3des esp-sha-hmac

crypto map StaticMap 20 match address outside_cryptomap_20
crypto map StaticMap 20 set peer REMOTEIP
crypto map StaticMap 20 set transform-set Site2Site
crypto map StaticMap 20 set pfs group2 [Tried with and without]

tunnel-group REMOTEIP type ipsec-l2l
tunnel-group REMOTEIP ipsec-attributes
pre-shared-key PRESHARE


crypto map StaticMap interface outside

access-list nonat extended permit ip 192.168.12.0 255.255.255.0 10.0.3.0 255.255.255.0
access-list nonat extended permit ip 192.168.12.0 255.255.255.0 172.16.0.0 255.255.240.0
nat (inside) 0 access-list nonat

#########
REMOTE B
#########
isakmp enable outside
isakmp identity auto
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption aes
isakmp policy 10 hash sha
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400

access-list outside_cryptomap_20 permit ip 10.0.3.0 255.255.255.0 192.168.12.0 255.255.255.0
access-list outside_cryptomap_20 permit ip 172.16.0.0 255.255.240.0 192.168.12.0 255.255.255.0


crypto ipsec transform-set Site2Site esp-3des esp-sha-hmac

crypto map StaticMap 20 match address outside_cryptomap_20
crypto map StaticMap 20 set peer REMOTEIP
crypto map StaticMap 20 set transform-set Site2Site
crypto map StaticMap 20 set pfs group2 [Tried with and without]

tunnel-group REMOTEIP type ipsec-l2l
tunnel-group 99.REMOTEIP ipsec-attributes
pre-shared-key PRESHARE


crypto map StaticMap interface outside

access-list nonat extended permit ip 10.0.3.0 255.255.255.0 192.168.12.0 255.255.255.0
access-list nonat extended permit ip 172.16.0.0 255.255.240.0 192.168.12.0 255.255.255.0
nat (inside) 0 access-list nonat

#####################################
Here is a part of the debug: REMOTE B
#####################################
Aug 18 07:18:25 [IKEv1 DEBUG]: IP = REMOTEIP, IKE MM Responder FSM error history (struct &0x351ecd8) <state>, <event>: MM_DONE, EV_ERROR-->MM_WAIT_MSG3, EV_TIMEOUT-->MM_WAIT_MSG3, NullEvent-->MM_SND_MSG2, EV_SND_MSG-->MM_SND_MSG2, EV_START_TMR-->MM_SND_MSG2, EV_RESEND_MSG-->MM_WAIT_MSG3, EV_TIMEOUT-->MM_WAIT_MSG3, NullEvent
Aug 18 07:18:25 [IKEv1 DEBUG]: IP = REMOTEIP, IKE SA MM:1383969c terminating: flags 0x01000002, refcnt 0, tuncnt 0
Aug 18 07:18:25 [IKEv1 DEBUG]: IP = REMOTEIP, sending delete/delete with reason message
Aug 18 07:18:25 [IKEv1]: IP = REMOTEIP, Removing peer from peer table failed, no match!
Aug 18 07:18:25 [IKEv1]: IP = REMOTEIP, Error: Unable to remove PeerTblEntry
Aug 18 07:18:26 [IKEv1 DEBUG]: IP = REMOTEIP, IKE MM Responder FSM error history (struct &0x351f478) <state>, <event>: MM_DONE, EV_ERROR-->MM_WAIT_MSG3, EV_TIMEOUT-->MM_WAIT_MSG3, NullEvent-->MM_SND_MSG2, EV_SND_MSG-->MM_SND_MSG2, EV_START_TMR-->MM_SND_MSG2, EV_RESEND_MSG-->MM_WAIT_MSG3, EV_RESEND_MSG-->MM_WAIT_MSG3, NullEvent
Aug 18 07:18:26 [IKEv1 DEBUG]: IP = REMOTEIP, IKE SA MM:c8b7e093 terminating: flags 0x01000002, refcnt 0, tuncnt 0
Aug 18 07:18:26 [IKEv1 DEBUG]: IP = REMOTEIP, sending delete/delete with reason message
Aug 18 07:18:26 [IKEv1]: IP = REMOTEIP, Removing peer from peer table failed, no match!
Aug 18 07:18:26 [IKEv1]: IP = REMOTEIP, Error: Unable to remove PeerTblEntry

I am starting to think it has to do woth trying XAUTH but ASA does not use isa key .......... noxauth

Double check the config, second eyes is always helpfull?


 
Upvote 0 Downvote
Resolved.

I missed putting in the outside default route!

I also had to use dynamic maps as one end was a dynamic IP.
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

Sameer258
  • Locked
  • Question
Need Help to Find ip and mac address with email who one open my email
Replies
0
Views
141
Sameer258
Sameer258
XLNTech1
  • Locked
  • Question
iptables port forwarding
Replies
0
Views
119
XLNTech1
XLNTech1
Tommy_T
  • Locked
  • Question
Sonic wall - Have an issue remotely connectioning VNC and SMB (and AFP) to one of the 2 ISP circuits
Replies
1
Views
116
nnaarrnn
nnaarrnn
intel233
  • Locked
  • Question
Cisco ASA - VPN Question
Replies
6
Views
146
intel233
intel233
Sparrow4
  • Locked
  • Question
Configure Avaya IPO R11 / VM Pro + Office365 or Exchange for voicemail to email
Replies
2
Views
140
Johnkite
Johnkite

Part and Inventory Search

Sponsor

Back
Top