I have a customer who has SIP trunking at one location, and they have another IP Office at another location that just has 4 analog lines. Both IP Offices' are 406 on 4.2 software. Because the phone company at the phone system with the analog lines would not release the numbers to the carrier they are doing SIP trunking with, they could not port those numbers over to the SIP trunk, therefore they had to come in as analog lines. However, I want outgoing calls from that phones system to go through the other phone system that has the SIP trunking, I figured the way I would do this is to make the line group ID on the ARS table the same as the one on the other phone system (even though it wasn't on the dropdown) but all I got was a waiting-for-line, what can I do to make this work?
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
SIP Trunking Routing
- Thread starter Bibbyboy
- Start date
- Thread starter
- #21
Not if you don't put the 9N;/Dial/N"@xxx.xxx.xxx.xxx" in the ARS!!! The ?/Dial/./ARS needs to be in the Shortcode list.
You could try to add a 9N/Dial/9N/ARS in the Shortcodes, it could be that it not looking to the ? in the short codes.
This all needs to be done on the SIP site, on the other site you've already did add the 9N/Dial/9N/LineID of the SCN link.
___________________________________________
It works! Now if only I could remember what I did...
___________________________________________
You could try to add a 9N/Dial/9N/ARS in the Shortcodes, it could be that it not looking to the ? in the short codes.
This all needs to be done on the SIP site, on the other site you've already did add the 9N/Dial/9N/LineID of the SCN link.
___________________________________________
It works! Now if only I could remember what I did...
___________________________________________
- Thread starter
- #23
Ok, I did that and people at the SIP Trunk phone system site were still able to make outbound calls 
, but the people at the other phone system still got the number busy , when I look at the call status I can see it going out the sip line....its like its almost there but not quite.
, but the people at the other phone system still got the number busy , when I look at the call status I can see it going out the sip line....its like its almost there but not quite.Do they send out a DDI number that is not on the sip line ?
That could be your problem
ACS - Implement IP Office
ACA - Implement IP Telephony -- ACA - Design IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
That could be your problem
ACS - Implement IP Office
ACA - Implement IP Telephony -- ACA - Design IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
OK on the NOT sip site, try to do almost the same.
remove the 9N/Dial/N/xxx in the ShortCodes, add the ?/Dial/./ARS
Add a 9N/Dial/9N/LineID SCN in the ARS.
___________________________________________
It works! Now if only I could remember what I did...
___________________________________________
remove the 9N/Dial/N/xxx in the ShortCodes, add the ?/Dial/./ARS
Add a 9N/Dial/9N/LineID SCN in the ARS.
___________________________________________
It works! Now if only I could remember what I did...
___________________________________________
- Thread starter
- #26
Its interesting you bring that up, the phone system without the SIP trunking has 4 copper lines, incoming calls come to those, because the phone company down there would not release the number (so that we could've ported those numbers on the SIP trunk and been done with it). So we were just going to have that phone system dial in/out on those 4 lines, well...the IT guy wants their outgoing to come through the other phone system, but wants to push out the main number...well since the SIP tab on the user profile controls their own caller ID, I made a fictious SIP line on the phone system to bring up that SIP tab on the user profile, and then I could put the main number in each of the users sip tabs..and when I look at monitor it is indeed pushing out that number, except that were getting a busy....you think that is what is causing this?? If thats the case, what can I do to push out the main number?
Try using NW in the telephone number field of your shortcode
Just add the W (Witheld)
Remove the fake sipline and uri number at the users
That will not be used anyway
ACS - Implement IP Office
ACA - Implement IP Telephony -- ACA - Design IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
Just add the W (Witheld)
Remove the fake sipline and uri number at the users
That will not be used anyway
ACS - Implement IP Office
ACA - Implement IP Telephony -- ACA - Design IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
Add a SIP URI on "Use Authentication Data" not on
"Use User data" make the Outgoing Group on higher lets 201.
You'll need to change the whole thing now.
NOT SIP Site;
ARS;
9N/Dial/#9N/LineID SCN
SIP Site;
ARS;
#9N;/Dial/N"@xxx.xxx.xxx.xxx"/201 for the Line Group ID
___________________________________________
It works! Now if only I could remember what I did...
___________________________________________
"Use User data" make the Outgoing Group on higher lets 201.
You'll need to change the whole thing now.
NOT SIP Site;
ARS;
9N/Dial/#9N/LineID SCN
SIP Site;
ARS;
#9N;/Dial/N"@xxx.xxx.xxx.xxx"/201 for the Line Group ID
___________________________________________
It works! Now if only I could remember what I did...
___________________________________________
- Thread starter
- #29
Not in europe
Overhere you can not send a number that is not part of the bundle
ACS - Implement IP Office
ACA - Implement IP Telephony -- ACA - Design IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
Overhere you can not send a number that is not part of the bundle
ACS - Implement IP Office
ACA - Implement IP Telephony -- ACA - Design IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
IPOfficeIreland
Technical User
On my sip server you can send any number you want!
hahahaha
that it great, here it seems that the providers don't care as long as they get their money at the end of the month. I send caller ID 666-666-6666 when I call out and as a name I send now GuessWho, but only because my wife didn't like me sending TheDevil any more.
Sometimes I wish I could combine Europe with North America and get the best of both worlds but that would be being greedy.
Joe W.
FHandw., ACS
If you can't be good, be good at it!
that it great, here it seems that the providers don't care as long as they get their money at the end of the month. I send caller ID 666-666-6666 when I call out and as a name I send now GuessWho, but only because my wife didn't like me sending TheDevil any more.
Sometimes I wish I could combine Europe with North America and get the best of both worlds but that would be being greedy.
Joe W.
FHandw., ACS
If you can't be good, be good at it!
I have not tried that and I guess I won't do that either, they are pretty nasty with that when they catch you.
On the other hand I might just try that tonight and tell you tomorrow.
Joe W.
FHandw., ACS
If you can't be good, be good at it!
On the other hand I might just try that tonight and tell you tomorrow.
Joe W.
FHandw., ACS
If you can't be good, be good at it!
I am sure that I do not won 666-666-6666 otherwise I am getting afraid and stay at work rather the going home now.
I sent actually the caller ID of a friend when I called him and he was quite surprised when he answered the phone.
So the answer is yes, I can send whatever I like and it seems to go through, but that doesn't mean it works with every line provider.
Joe W.
FHandw., ACS
If you can't be good, be good at it!
I sent actually the caller ID of a friend when I called him and he was quite surprised when he answered the phone.
So the answer is yes, I can send whatever I like and it seems to go through, but that doesn't mean it works with every line provider.
Joe W.
FHandw., ACS
If you can't be good, be good at it!
- Thread starter
- #38
Woo hoo! Thank you bas1234, what you gave me yesterday worked like a champ. I have yet another question though. The caller ID for phone system that does NOT have SIP trunking came up with one of the four copper lines, it came up as their 3rd line...how do I only push out the number of the first line...Im not even sure how it knew to push out the 3rd lines number.
Maxwell1001
Vendor
my wicked side wants to know how your sending 911 etc
i am using use "Use Authentication Data" and SIP Number on Local URI
shortcode
9N;
N"@sip.voiceflex.com"
i feel an inhouse practical joke coming on!!!
ACA - IP Office
ACS - IP Office
i am using use "Use Authentication Data" and SIP Number on Local URI
shortcode
9N;
N"@sip.voiceflex.com"
i feel an inhouse practical joke coming on!!!
ACA - IP Office
ACS - IP Office
@Maxwell1001,
You could try to add a new SIP uri, and instead of selecting "Use Authentication Name" or "Use User Data" enter any number you want on;
Local URI
Contact
Display Name
Over here in the Netherlands we're only allowed to send the number you have from the provider.
___________________________________________
It works! Now if only I could remember what I did...
___________________________________________
You could try to add a new SIP uri, and instead of selecting "Use Authentication Name" or "Use User Data" enter any number you want on;
Local URI
Contact
Display Name
Over here in the Netherlands we're only allowed to send the number you have from the provider.
___________________________________________
It works! Now if only I could remember what I did...
___________________________________________
- Status
Similar threads
