SIP question Rls 6 CS1000 system

[nortelmel]

Hi folks,
Can anyone help me figure out why I dont see the far end SIP Sig Server IP in these traces? I have Dch messages turned on on both systems. One is 4.5 and the other 6. I'm only getting messages from the 4.5 system. I have SIP tracing on for both Sig servers but only get messages from the 4.5 system. Please see trace below. Rls 4.5 and 6 systems have current patches


Call 1

6.0 PBX (ext 7000) to 4.5 PBX (ext 7700)
*****************************************************************************************

trac 104 0 0 7

ACTIVE VTN 104 0 00 07

ORIG VTN 104 0 01 00 KEY 0 SCR MARP CUST 0 DN 7000 TYPE 2004P2
SIGNALLING ENCRYPTION: INSEC
MEDIA ENDPOINT IP: 192.168.1.66 PORT: 5200
TERM VTN 104 0 00 07 VTRK IPTI RMBR 20 8 OUTGOING VOIP GW CALL
FAR-END SIP SIGNALLING IP: 0.0.0.0 <---------------Is
this the problem???
FAR-END MEDIA ENDPOINT IP: 0.0.0.0 PORT: 0
FAR-END VendorID: Not available
MEDIA PROFILE: CODEC n/a NO-LAW PAYLOAD 1 ms VAD OFF
RFC2833: RXPT 101 TXPT N/A DIAL DN 7700
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 19 TERM 19
EES_DATA:
NONE
QUEU NONE
CALL ID 0 34996


AUX NARS



---- ISDN ISL CALL (TERM) ----
CALL REF # = 392
BEARER CAP = VOICE
HLC =
CALL STATE = 3 OUTGOING
CALLING NO = 7000 NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP
CALLED NO = 7700 NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP


Call 2

4.5 PBX (ext 7700) to 6.0 PBX (ext 7000)

***************************************************************************

.trac 0 7700
DCH 20 OMSG SETUP REF 00000188 CH 62 0 0 7 TOD 14:03:06
FEAT :CRID
FEAT :CDS
FEAT :NCID
PROGRESS: ORIG ADDR IS NOT ISDN
CALLING #:7700 NUM PLAN: PRIVATE/ABBREVIATED (CDP)
CALLED #:7000 NUM PLAN: PRIVATE/ABBREVIATED (CDP)

DCH 20 IMSG CALLPROC REF 00000188 CH 62 0 0 7 TOD 14:03:06


ACTIVE VTN 061 0 00 00

ORIG VTN 061 0 00 00 KEY 0 SCR MARP CUST 0 DN 7700 TYPE I2004
MEDIA ENDPOINT IP: 192.168.1.65 PORT: 5200
TERM VTN 062 0 00 07 VTRK IPTI RMBR 20 8 OUTGOING VOIP GW CALL
FAR-END SIP SIGNALLING IP: 0.0.0.0
FAR-END MEDIA ENDPOINT IP: 0.0.0.0 PORT: 0 MEDIA PROFILE: CODEC n/a A-law PAYLOAD 1 ms VAD OFF DIAL DN 7000
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 20 TERM 20
EES_DATA:
NONE
QUEU NONE
CALL ID 0 294


AUX NARS



---- ISDN ISL CALL (TERM) ----
CALL REF # = 392
BEARER CAP = VOICE
HLC =
CALL STATE = 3 OUTGOING
CALLING NO = 7700 NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP
CALLED NO = 7000 NUM_PLANRIVATE TON:ABBREVIATED ESN:CDP




thanks

mel

 

[allenmac]

In release 5.5 and above, you need to tell the switch that you want the d-channel messages displayed on your TTY.

In LD 96
ENL MON TTY

That will direct the d-channel messaging to the TTY.

 

[nortelmel]

Thanks for your help and it worked ok. But Why do I still have no IP addresses...see print

FAR-END SIP SIGNALLING IP: 0.0.0.0 <---------------Is
this the problem???
FAR-END MEDIA ENDPOINT IP: 0.0.0.0 PORT: 0
FAR-END VendorID: Not available

 

[Reusser]

does the call complete?

Usually will not see far end until call is established to far end.

 

[nortelmel]

Hey Reusser, Thanks for your response! No the call gets rejected and I cannot fogure out why..Frustrated to the MAX!!!!!

What do you think????

 

[Reusser]

that is why you do not see far end server info.

Give us info on 7700
CDP?
what type virtual route - SIP/H323?
Where is NRS?
Did it work before upgrade?
are both sites registered to NRS?
What do you see with DCH messaging turned on?