Send CLID on my outgoing PRI 5

[fm62564]

I have 2 PRI's with D Chn's and need them configured to send the CLID. Right now its just sending the BTN. How can I set these up to send the area/pre and DID?

Thanks

 

[bigindian65]

How's your RCAP set on the Dch? ND2?

Mato' Was'aka

 

[fm62564]

Where would I check that?

thanks

 

[bigindian65]

ld 22
prt
adan dch xx

Mato' Was'aka

 

[fm62564]

RCAP COLP

 

[hawks]

You might also need to go into LD 15 and build the CLID Tables that you want to use.

 

[phonz1]

have to disable the DCH to change it, need to add ND2 and do you have a CLID table built and assigned to the phones??

LD 21
PRT
CLID

 

[fm62564]

I'm green in this area but here's what printed out
REQ: PRT

TYPE: CLID
CUST 0
SIZE 256
RNGE
INTL
ENTRY 0
HNTN
ESA_HLCL 11
ESA_INHN NO
ESA_APDN YES
HLCL
DIDN YES
HLOC
LSC
CLASS_FMT DN

 

[GHTROUT]

I would rather see you do what was posted first.

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[GHTROUT]

Then you can modify your CLID using these guides:

http://www.ghtrout.com/ghtrout/files/CLID_Documentation_from_Nortel.zip

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[fm62564]

Set the rcap to ND2?

 

[bigindian65]

yes, might have to do off-hours, disable Dch in ld 96 chg in ld 17

Mato' Was'aka

 

[fm62564]

Thanks everyone. I really appreciate all the input. I'll have to try these out tomorrow as I have to sign out for the day.

Thanks again, FM

 

[telebub]

What does setting the RCAP to ND2 have to do with outbound CLID? It seems to me he just needs to modify entry 0 that he posted above and to verify the CO is allowing his PBX the control of the outbound CLID.

War Eagle!
Lions Baseball '09!

 

[GHTROUT]

I agree 100% I'm was previously agreeing with the wrong people I guess

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[bigindian65]

My bad telebub...too much jack daniels today..i dunno... *

Mato' Was'aka

 

[GHTROUT]

Ya, really Big-I! How dare you look so "smart"

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]

 

[telebub]

Yeah BigI, don't drink too much today, you need to save some for tomorrow.

War Eagle!
Lions Baseball '09!

 

[fm62564]

telebub, what do I need to modify on entry 0? I'm calling Telco now to make sure they are allowing it.

Thanks

 

[GHTROUT]

Here are a variety of examples. If you search here on the text "HLCL", there are lots of posts that show other ways to set it.


thread798-1496201

thread798-1496090

thread798-1476711

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]