SCPW Password not working on 1000E

[JAAGB]

Hi All,
I installed a 1000E on that SCPW password was given for international acces, If i use 20 to open 21 to close....if i open the extension and dial the international number, I am getting release and try again...but in authcode was working fine..please any help

 

[dlesap]

SCPW and Authorisation codes are differents. AUT are define in LD 88. SCPW is station password for other features than AUT: Remote call forward, COS, Call forward, ....
AUT access is done by using FFC AUTH then AUT. they are open to all set by default.
Give print of what you did and comments for each block of datas

 

[JAAGB]

I made a block for international access using FRL and NCOS.
I have to allow some users so inter national access with the password.
i was tring the SCPW to give a access for the users but its not working. the authcode we gave to use each and every call. The scpw onec open and make calls then evening they close the extension.
which all the Blocks u need prt?

 

[JAAGB]

REQ: prt
TYPE: ffc
TYPE FFC_DATA
CUST 0

TYPE FFC_DATA
CUST 00
CCRS UNR
SCPL 4
SBUP YES
FFCS YES
STRL 1
STRG #
ADLD 10
DFLT_SCPW NO



REQ: prt
TYPE: ccs
TYPE CCS_DATA
CUST 0

TYPE CCS_DATA
CUST 00
CCRS UNR
ECC1 UNR
ECC2 UNR
CNCS 0
PELK NO

 

[dlesap]

This an example for aut:
>ld 57
REQ prt
TYPE ffc
CUST 0
CODE auth

CUST 00
FFCT YES
AUTH 10

>ld 88
REQ prt
TYPE aub
CUST 0
SPWD

CUST 00
ALEN 05
ACDR YES
AUTHCOD_ALRM ON
RANR X
ACLE YES
BRST 05
RTRY YES
RAN2 X
AUTO NO

CLAS COS TGAR NCOS CLAS COS TGAR NCOS CLAS COS TGAR NCOS

000 TLD 15 07 001 UNR 15 07 002 CTD 01 00
003 CTD 01 00 004 CTD 01 00 005 CTD 01 00

ld 88
REQ prt
TYPE aut
CUST 0
SPWD
CODE

CODE 10629 CLAS 000
CODE 10630 CLAS 000

Then user dials : 10(AUTH) 10629 (AUT)

 

[dlesap]

What you are trying to do is COS need CLS CCSA. Then using a COS KEY can open or close set with its NCOS. Used in Hotels or Hospitals environment or in special case.

 

[JAAGB]

My Authcode was working fine i was looking for SCPW(station Control Possword) to work

 

[dlesap]

Use SCPW to block or open station as described above. When set is open it follows its NCOS. When it's closes it follows CCRS define in CCS LD 15

 

[JAAGB]

REQ: prt
TYPE: ffc
TYPE FFC_DATA
CUST 0

TYPE FFC_DATA
CUST 00
CCRS UNR
SCPL 4
SBUP YES
FFCS YES
STRL 1
STRG #
ADLD 10
DFLT_SCPW NO

 

[dlesap]

This my conf:

TYPE CCS_DATA
CUST 00
CCRS FRE
ECC1 FRE
ECC2 FRE
CNCS 0
PELK YES

TYPE FFC_DATA
CUST 00
CCRS FRE
SCPL 5
SBUP YES
FFCS NO
STRL 0
STRG
ADLD 0
DFLT_SCPW YES

On segt:
DES I2004
TN 065 0 00 00 VIRTUAL
TYPE I2004
CDEN 8D
CUST 0
ZONE 010
FDN 6200
TGAR 8
LDN NO
NCOS 7 NCOS 7 is open to int'l
SGRP 0
RNPG 0
SCI 0
SSU 0010
LNRS 16
XLST 0
SCPW 12345
SFLT NO
CAC_MFC 0
CLS TLD FBD WTA LPR MTD FNA HTA TDD HFA CRPA
MWA LMPX RMMD SMWD AAD IMD XHD IRA NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSA-CSI SWD LNA CNDA

This set is actually open to int'l

To turn it to restricted:
KEY COS on any set or attendant then SCPW then DN
or on BGD port : se st "DN" co on to block or se st "DN" co of to open

When set is blocked : CLS CCSA-CSA comes automatically

 

[JAAGB]

TN 100 0 00 00 VIRTUAL
TYPE I2002
CDEN 8D
CTYP XDLC
CUST 0
NUID
NHTN
ZONE 001
FDN
TGAR 1
LDN NO
NCOS 3
SGRP 0
RNPG 0
SCI 0
SSU
LNRS 16
XLST
SCPW 1111
SFLT NO
CAC_MFC 0
CLS UNR FBD WTA LPR MTD FND HTD ADD HFD CRPD
MWD LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSA-CSI-L SWD LNA CNDA
CFTD SFD MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD LLCN MCTD CLBD AUTU
GPUD DPUD DNDD CFXD ARHD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AGRD MOAD
UDI RCC HBTD AHD DDGA NAMA MIND PRSD NRWD NRCD NROD
DRDD EXR0
USRD ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC DNDY DNO3 MCBN
FDSD NOVD VOLA VOUD CDMR
CPND_LANG ENG
HUNT
PLEV 02
CSDN
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
DNDR 0
KEY 00 SCR 75598 0 MARP
CPND
CPND_LANG ROMAN
NAME Jeanly Arasu
XPLN 27
DISPLAY_FMT FIRST,LAST
01
02
03
04

 

[JAAGB]

TN 100 0 00 00 VIRTUAL
TYPE I2002
CDEN 8D
CTYP XDLC
CUST 0
NUID
NHTN
ZONE 001
FDN
TGAR 1
LDN NO
NCOS 3
SGRP 0
RNPG 0
SCI 0
SSU
LNRS 16
XLST
SCPW 1111
SFLT NO
CAC_MFC 0
CLS UNR FBD WTA LPR MTD FND HTD ADD HFD CRPD
MWD LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSA-CSI-L SWD LNA CNDA
CFTD SFD MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD LLCN MCTD CLBD AUTU
GPUD DPUD DNDD CFXD ARHD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AGRD MOAD
UDI RCC HBTD AHD DDGA NAMA MIND PRSD NRWD NRCD NROD
DRDD EXR0
USRD ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC DNDY DNO3 MCBN
FDSD NOVD VOLA VOUD CDMR
CPND_LANG ENG
HUNT
PLEV 02
CSDN
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
DNDR 0
KEY 00 SCR 75598 0 MARP
CPND
CPND_LANG ROMAN
NAME
XPLN 27
DISPLAY_FMT FIRST,LAST
01
02
03
04

 

[dlesap]

Your TN is actually electronically locked: CLS CCSA-CSI-L
Unlocked it using FFC ELKD + SCPW
You will see CLS comes to CCSA-CSI
Then apply setting i gave before and try

When answering messages, give comments and what actions you done on set and which changings you made in programming. Only prints are not enough...

 

[JAAGB]

I was really sorry...i was in hurry i send the post with out comments...see now other TN even CCSA-CSI (no lock) the calls are not going...where could be the problem??

DES TEST
TN 100 0 00 01 VIRTU
TYPE I2050
CDEN 8D
CTYP XDLC
CUST 0
NUID
NHTN
ZONE 001
FDN
TGAR 0
LDN NO
NCOS 3
SGRP 0
RNPG 0
SCI 0
SSU
LNRS 16
XLST
SCPW 1111
SFLT NO
CAC_MFC 0
CLS UNR FBD WTA LPR MTD FND HTD TDD HFA CRPD
MWD LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSA-CSI SWD LNA CNDD
CFTD SFD MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD LLCN MCTD CLBD AUTU
GPUD DPUD DNDD CFXD ARHD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AGRD MOAD
UDI RCC HBTD AHD DDGA NAMA MIND PRSD NRWD NRC
DRDD EXR0
USRD ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC DNDY DNO3 MCBN
FDSD NOVD VOLA VOUD CDMR
CPND_LANG ENG
HUNT
PLEV 02
CSDN
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
DNDR 0
KEY 00 SCR 77777 0 MARP
01 SCR 71310 0 MARP
02 SCR 71303 0 MARP
03 SCR 71004 0 MARP
04 SCR 71304 0 MARP
05
06
07

 

[dlesap]

CLS UNR means there is no restrictions due to NCOS level.
Check TGAR in that example it's set to 0 versus example before where it was TGAR 1. Try to change it to a higher level: 1, 2, 3... and try to call each time

 

[JAAGB]

Hi all,
I changed the setting elka to 21 and elkd 20 now its working...
before
elka was 20
elkd was 21

I dont know which one was currect can any one tell me

 

[dlesap]

There no such default values for FFC codes. It can be any digits

 

[JAAGB]

no i was asking for open elka and close elkd is it??

 

[dlesap]

ELKA is for locking the set
ELKD is for unlock it

 

[GHTROUT]

And to confirm, Flexible Feature Codes can be defined in any format you have free digits - For ecample - really - I have over 200 different codes assigned to RGAA "Ring Again Activate" That is where I store DNs I do not want anyone to ever assign to phones.

~

http://www.GHTROUT.com/