Route Map using Named ACL

[ramizbsd]

Dears All,
I have gateway router 7206vxron which I have two wan links. I want to distribute my traffic using Route-Map with named acl. I followed the document related to named acl

http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a0080431038.html

Now problem is, the document says in step 4 and 5 that we can use optional parameter [sequence-number] so that we can edit named acl or place new entry any where in acl based on this [sequence-number]. But In real when tried to implement it on gateway router, I could not. Sequence number had not been accepted.

FLAG-Gate#
FLAG-Gate#conf t
Enter configuration commands, one per line. End with CNTL/Z.

FLAG-Gate(config)#ip access-list extended MyACL
FLAG-Gate(config-ext-nacl)#?
Ext Access List configuration commands:
default Set a command to its defaults
deny Specify packets to reject
dynamic Specify a DYNAMIC list of PERMITs or DENYs
evaluate Evaluate an access list
exit Exit from access-list configuration mode
no Negate a command or set its defaults
permit Specify packets to forward
remark Access list entry comment

FLAG-Gate(config-ext-nacl)#1000 permit ip host 192.168.161.168 any
^
% Invalid input detected at '^' marker.

FLAG-Gate(config-ext-nacl)#

So what would be the reason? Why I could not enter sequence # 1000? Without it command was acceptable.
Waiting for Response

Regards,

 

[KiscoKid]

What version of IOS do you have? Use the 'show version' command to check.

I believe this feature was introduced in IOS 12.3.

 

[ramizbsd]

Dear KiscoKid,

Gateway#
Gateway#show version
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-JS-M), Version 12.2(34), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Thu 02-Mar-06 04:32 by pwade
Image text-base: 0x60008940, data-base: 0x6168E000

ROM: System Bootstrap, Version 12.2(4r)B2, RELEASE SOFTWARE (fc2)
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

<Rest of the output I omitted>

Regards

 

[KiscoKid]

Your IOS levels are too low - 12.2(34).
Can you upgrade to 12.3 or 12.4 and see how you go.

 

[ramizbsd]

Dear KiscoKid,
Ok thanks for responding. Tell me if i don't want to upgrade ios and still want to insert an entry in between some other entries. Is it posible?

For Example
First i have acl entries

ip access-list extended Test
permit ip host 192.168.12.5 any
permit ip host 192.168.13.2 any
permit ip 192.168.200.0 0.0.0.255 any
permit ip 172.16.10.0 0.0.0.255 any

now i want to add an acl entry "deny ip host 192.168.200.5 any" in between "permit ip host 192.168.13.2 any" and "permit ip 192.168.200.0 0.0.0.255 any" so that route-map would apply on network 192.168.200.0 except host 192.168.200.5.

How is it possible without sequence number?
Regards

 

[vipergg]

It isn't possible , you would have to temp pull the ACL change it in a notepad and paste it back it . Numbered ACL started with 12.2T train or 12.3 mainline , you are at 12.2 mainline so if doesn't numbering capability.