rfp 32 from avaya to mitel

[dirokkato]

Hello

I have an RFP32 previously installed on avaya system.now i would like to install in a OMM Mitel system but when i connect it gives me an error.i have already tried aastra omconfigurator but i can't reset it to factory default.
Is there a way to reset or transform ?

 

[Supernova99]

This should be entirely possible with the correct firmware.

This is some info from the Ascom troubleshooting manual

Load Firmware Using the Gwload Tool

Download the Gwload software and the latest .bin file to a folder i.e. C:\gw

Set the IPBS in TFTP-mode by performing a medium (~3 sec) hardware reset

Start a command window, change to the folder where GWloader is located

To update the IPBS with the new firmware execute the following command from the
folder where the gwload.exe file is located:
gwload /setip /i 172.20.10.157 /prot ip1201.bin /gwtype 1201
– The command gwload/find verifies that your IPBS is in TFTP mode
– The ip-address can be any free address in your network
– The .bin file in this case is “ip1201.bin”
– If the download fails, try to connect your PC directly to the IPBS

You may have to contact Ascom to get the correct firmware

Share what you know - Learn what you don't

 

[boycey9]

isnt that the Detewe one?, if so you can telnet to it, i think there was a reset in the ommconsole

 

[dirokkato]

it is a detewe rfp.
i've already tried to reset parameter by aastra OMconfigurator but when boot up it don't work.
i can't find user and password to login by telnet on mitel version.
i think it's a boot or firmware problem

 

[boycey9]

telnet to OMM
username iprfp
Password OpenMobi
Type ommconsole
Type cnf login

 

[dirokkato]

this is the rfp that don't work :


10.1.15.25 > flash
version of initial booter : 2.0.12
Version of booter 1 : 3.4.4
Version of booter 2 : 3.4.4
Hardware Revision : 51
MAC address : 00:30:42:0E:31:8C
branding : AVAYA(JOKER)


and this is my OMM Mitel

10.1.15.20 > flash
version of initial booter : 2.0.12
Version of booter 1 : 2.1.2
Version of booter 2 : 2.1.2
Hardware Revision : 51
MAC address : 00:30:42:0A:CF:71
not yet branded

How can I change version of booter and branding?

 

[boycey9]

The firmware is on the Mitel controller and I dont know anyway of doing it other than DHCP, have you tried setting it back to DHCP and using the options as below

The DHCP server must be configured with the following options:
• Option 66 - Boot Server Host Name (typically the IP Address of the 3300 ICP RTC)
• Option 67 - Bootfile Name (iprfp.bin)
• Option 140 - IP Address of the primary OpenMobility Manager
• Option 150 - IP Address of the secondary OpenMobility Manager (required for a resilient
OMM system)
• Option 224 - The value, "OpenMobility", is required by the RFP DHCP client to deter-
mine which DHCP servers are valid.
When configuring the DHCP server, the following are optional:
• Option 141 - identifies the Syslog Daemon server
• Option 142 - determines server port of the Syslog Daemon
• Option 254 - automatically updates the booter version (from 2.x to 3.y).
Once Options 140 and 150 are configured and reservations for those two options are made,
the active and inactive OMMs are designated. Once the primary and secondary OMMs are
designated, all other RFPs can get their IP Addresses dynamically.
Options 141 and 142 relate to the Syslog Daemon and are not required for the system to
operate, but can be configured either through the OMM or at the DHCP server. For instructions
on how to configure both options from the OMM, see “Configuring System Settings” on page 53.
Please note that DHCP server options can change from release to release. The following table
shows the DHCP options currently used.

Note: To fully update the Booter version, the RFPs must be rebooted twice. To verify
the Booter version, log into the RFP through a Telnet session.