Restrict outbound calling 1

[gv82]

I'm trying to disable outbound dialing on a 2050 softphone. Setting NCOS to 0 didn't do the trick. I tried adding CLS FRE2 but it doesn't show when I print the tn...

Any idea what I'm doing wrong? The following TN can still make local and longdistance calls.

REQ: chg
TYPE: i2050
TN 70 1
ECHG yes
ITEM cls fre2
ITEM

MEM AVAIL: (U/P): 2683995 ...

REQ: prt
TYPE: tn
TYPE TNB
TN 70 1
DATE
PAGE
DES
DES 7887
TN 070 0 00 01 VIRTUAL
TYPE I2050
CDEN 8D
CUST 0
ZONE 001
FDN 6000
TGAR 0
LDN NO
NCOS 0
SGRP 0
RNPG 0
SCI 0
SSU
LNRS 16
XLST 0
SCPW
SFLT NO
CAC_MFC 0
CLS UNR FBD WTA LPR MTD FNA HTA ADD HFA CRPD
MWA LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSD SWD LNA CNDA
CFTD SFD MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD LLCN MCTD CLBD AUTU
GPUD DPUD DNDA CFXA ARHD FITD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AGRD MOAD AHD
DDGA NAMA
DRDA
USRD ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC DNDY DNO3 MCBN
FDSD NOVD VOLA VOUA CDMR ICRD
CPND_LANG ENG
RCO 0
HUNT 6000
LHK 0
PLEV 02
CSDN
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
DNDR 0
KEY 00 SCR 7887 0 MARP
DNRO 0
DNRI 0
CPND
CPND_LANG ROMAN
NAME XXXXXXXXXXXX
XPLN 27
DISPLAY_FMT FIRST,LAST
CPND_LANG KATAKANA
NAME XXXXXXXXXXXX
XPLN 27
DISPLAY_FMT FIRST,LAST
01 ADL 24
02 ADL 24
03 ADL 24
04 ADL 24
05 ADL 24
06
07
08
09
10
11
12
13
14
15
16 MWK 6000
17 TRN
18 AO6
19 CFW 16
20 RGA
21 PRK
22 RNP
23
24
25
26
27
28
29
30
31
DATE 30 DEC 2008


NACT

 

[tnphoneman]

Forst off UNR will allow them to dial the route access code and then make the call. Change to CTD.

You might also want to try SRE or FR2. What do they dial for an outside line? You could also TGAR them off all trunk routes but that will affect incoming also.

Signature===========================================

http://www.greatwhitetechnologies.com

 

[GHTROUT]

I think the poster meant to enter "FR2" but was entering FRE2




~~~
[small]GHTROUT.com | Get the Input/Output Manuals | Tek-Tips FAQs | Recent Replies[/small]

 

[gv82]

Thank you! CTD and FR2 did the trick. I was about about to TGAR them off but TGAR isn't set on the trunks.

They press '0' to access outside lines (the system in Japan).

 

[GHTROUT]

CTD and FR2 cannot exist at the same time. FR2 was the trick.


~~~
[small]GHTROUT.com | Get the Input/Output Manuals | Tek-Tips FAQs | Recent Replies[/small]

 

[tnphoneman]

Yea well I can't spell either today. GH is right CTD and FR2 can not exist on the same set as they replace each other.

Signature===========================================

http://www.greatwhitetechnologies.com

 

[tnphoneman]

One thing you might want to check for future reference is what exactly "0" is in the PBX if it is the route access code then you are bypassing BARS programming and that would explain why the NCOS change did not work.

Signature===========================================

http://www.greatwhitetechnologies.com