Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Replacing tn2182 Tone Clock Board
- Thread starter Rob8158
- Start date
MattRutter
Vendor
I think it's as simple as:
Switch processing to carrier B
Power off carrier A
Swap tone board
Power up carrier A
I believe that the new tone clock has to be exactly the same revision etc as the old one.
Switch processing to carrier B
Power off carrier A
Swap tone board
Power up carrier A
I believe that the new tone clock has to be exactly the same revision etc as the old one.
mikeydidit
IS-IT--Management
Here are the power down procedures for a duplicated system.
I put this together for some of my tech's.
Replacing SPE circuit packs in a Duplicated system
Unlike a port carrier that is used for station circuit packs, you must power down one of the processors in a duplicated system before you can replace any circuit packs in that carrier. Always be sure to match the vintages on any circuit packs in A and B processors to insure their will be no conflicts in the software. Also before replacing any circuit packs to a higher vintage, make sure that our current version of software in the switch will support that pack. You can use the command “newterm” to display the current version of software. Below are the procedures for powering down a SPE.
1. Save translations
This step takes all translations on the 3 memory boards in both processors A&B and saves these translations to the hard drives in both processors.
Make sure that both processors show “Success” after this command completes.
2. Back up disk both full
This step saves all translations that have been saved to the hard drives and stores this information to the optical disk drives. Again this is done on A&B processors. The same is true for this command as with the save translations. Look to make sure that both SPE’s show “Success” after the command is complete.
3. Status SPE
This command will show the active and standby SPE locations. Make sure the SPE you need to shut down is in standby mode. If it is not, use the “Reset system I” command to change the SPE from active to standby. Use the status SPE command again to make sure the now active SPE is up and fully functional with no alarms present. Repeat this command until it is before proceeding.
4. Status Port Network
This command will allow you to see which tone clock is active and which is in the standby mode. You need to be sure that the active tone clock is in the active SPE that you are not taking down. If the tone clock is in the wrong SPE use the “Set tone clock” 01A or 01B to set it in the right SPE. The use the status port network command again to make sure it changed to the right SPE.
5. Power down procedures.
. Lock the SPE that you want “active” by using the toggle switches on the duplication interface pack. There are 3 positions on this. A, B, and auto select. One at a time, move the select switches on A and B SPE’s to the desired SPE setting on the duplication interface packs. This will lock the active SPE. You are now ready to power down the standby SPE. Remove the power cord to the left power supply first. Then remove the cord to the right power supply. Wait until there are no lights present on the power supplies. The offline processor is now down. At this time you can replace any pack in this carrier.
6. Power up procedures
After making sure that you have seated the circuit packs you have replaced correctly, you can now plug in the power cords to the power supplies. First plug in the power cord to the right power supply and then plug in the left power supply. Move the select switches on the duplication interface packs back to “Auto select”.
7.Alarm resolutions
The standby SPE should now be trying to come up. This may take 5 to 10 minutes. You can track this process using the status SPE command. This will show you the status of the hard drives, optical disk, processors and selector switches positions. It will also show you the status of the handshake, shadowing, and if the standby SPE is refreshed. After the standby SPE comes completely up is should show that
1. Handshake is up
2. Shadowing is on
3. Standby refreshed is yes
4. SPE selected is AUTO
5. State of health is functional
6. R-media and Disk are in-service
If the standby SPE does not come back up it may be necessary to do a “Busy out SPE standby” command. Then do a “release SPE standby” to make it functional again.
* To replace another circuit pack in the active SPE repeat all of the above steps.
Mikey
I put this together for some of my tech's.
Replacing SPE circuit packs in a Duplicated system
Unlike a port carrier that is used for station circuit packs, you must power down one of the processors in a duplicated system before you can replace any circuit packs in that carrier. Always be sure to match the vintages on any circuit packs in A and B processors to insure their will be no conflicts in the software. Also before replacing any circuit packs to a higher vintage, make sure that our current version of software in the switch will support that pack. You can use the command “newterm” to display the current version of software. Below are the procedures for powering down a SPE.
1. Save translations
This step takes all translations on the 3 memory boards in both processors A&B and saves these translations to the hard drives in both processors.
Make sure that both processors show “Success” after this command completes.
2. Back up disk both full
This step saves all translations that have been saved to the hard drives and stores this information to the optical disk drives. Again this is done on A&B processors. The same is true for this command as with the save translations. Look to make sure that both SPE’s show “Success” after the command is complete.
3. Status SPE
This command will show the active and standby SPE locations. Make sure the SPE you need to shut down is in standby mode. If it is not, use the “Reset system I” command to change the SPE from active to standby. Use the status SPE command again to make sure the now active SPE is up and fully functional with no alarms present. Repeat this command until it is before proceeding.
4. Status Port Network
This command will allow you to see which tone clock is active and which is in the standby mode. You need to be sure that the active tone clock is in the active SPE that you are not taking down. If the tone clock is in the wrong SPE use the “Set tone clock” 01A or 01B to set it in the right SPE. The use the status port network command again to make sure it changed to the right SPE.
5. Power down procedures.
. Lock the SPE that you want “active” by using the toggle switches on the duplication interface pack. There are 3 positions on this. A, B, and auto select. One at a time, move the select switches on A and B SPE’s to the desired SPE setting on the duplication interface packs. This will lock the active SPE. You are now ready to power down the standby SPE. Remove the power cord to the left power supply first. Then remove the cord to the right power supply. Wait until there are no lights present on the power supplies. The offline processor is now down. At this time you can replace any pack in this carrier.
6. Power up procedures
After making sure that you have seated the circuit packs you have replaced correctly, you can now plug in the power cords to the power supplies. First plug in the power cord to the right power supply and then plug in the left power supply. Move the select switches on the duplication interface packs back to “Auto select”.
7.Alarm resolutions
The standby SPE should now be trying to come up. This may take 5 to 10 minutes. You can track this process using the status SPE command. This will show you the status of the hard drives, optical disk, processors and selector switches positions. It will also show you the status of the handshake, shadowing, and if the standby SPE is refreshed. After the standby SPE comes completely up is should show that
1. Handshake is up
2. Shadowing is on
3. Standby refreshed is yes
4. SPE selected is AUTO
5. State of health is functional
6. R-media and Disk are in-service
If the standby SPE does not come back up it may be necessary to do a “Busy out SPE standby” command. Then do a “release SPE standby” to make it functional again.
* To replace another circuit pack in the active SPE repeat all of the above steps.
Mikey
- Thread starter
- #4
keep in mind people that once you force the spe into the stanby carrier you do not have to power down, just remove the processor and then you can pull and replace any common control card on the standby. once replaced just slide the processor back in and after it reboots refresh the standby, do a status system 1 or all and check to make sure the stanby is idle, then reset system interchange and make sure the standby comes up.
- Thread starter
- #6
- Status
Similar threads
- Locked
- Question
- Locked
- Question