Remote dial access to maintenance port sx-200 icp

[Laylobrown]

Having success with establishing a connection between modems but the characters that are showing up in hyperterminal looks like this...


€ø€ø€ø€ø€ø€ø€ø

I'm using the same hyerterminal window i use with direct connection.

I'm using an US Robitics Sportster faxmodem with x2

all dip-switches but 3 and 5 are down.

 

[pandabear1]

are you accessing at 9600 8 bits no parity and VT100 emulation?

 

[Laylobrown]

When i obtain a connection i hit enter 4 times and this pops up

€ø€ø€ø€ø€ø€ø€ø€ø€ø€ø€ø€ø€ø€øøøx<€€xÀ€øøA¿‹¼
1a¹D  `æßùýs2oPŠ
.`ÈÈæ÷·ôë4ò3õAP
üŸÜþ?½ºn£½ç8Œ@„þø?íRH|MÃ
¢Ê½úïÝNýy»“Ì|Ž0“ûwü½oÙ·v´
‚  ¥Úx¾ ø©Ó¯»Âfè þË?=
:’¹ ~çê ãº5?[#Iû~~ í岿ð _@€"°{üŒ—?—gø QIˆé í÷:Åš?€òhDÂ

 

[pandabear1]

what is the speed, parity and stop bits of hyperterminal set at?

 

[kwbMitel]

Force the USR to connect at 9600

AT Commands

AT&N6 - Upperlimit 9600
AT&U6 - Lowerlimit 9600
AT&W - Write to NVRAM
ATI4 - Display NVRAM

DIP Switch 7 controls whether the modem loads from default or NVRAM


*******************************************************
If we don't take care of the customer, Maybe they'll stop bugging us.

 

[pandabear1]

if you have access to Mitel on Line there is a bulletin on complete modem setup for the ICP

 

[pandabear1]

this is from a Mitel bulletin, there may be other ways also, this supersedes one Mitel put out in 2004.

The following cabling and AT command set are to be used when connecting an AT command compatible modem to the SX200 ICP. Our examples use USR 33.6 and V.92 modems. If you have a different modem that supports the AT command set, consult your modem manufacturer to determine the correct equivalent settings for that modem.

Step 1: Verify your USR 33.6 or V.92 modem register bits are setup as follows. To determine the modem's current settings, connect the modem to a laptop at 9600 8N1 with a straight through cable. Before powering on the modem, set dip switches 1,3 and 8 down, the rest of them up.
Type ati4 <enter>

ati4
USRobotics Sportster 33600 Fax Settings...

B0 E1 F1 M1 Q0 V1 X1 Y0
BAUD=9600 PARITY=N WORDLEN=8
DIAL=TONE ON HOOK

&A1 &B0 &C1 &D0 &G0 &H0 &I0 &K1 &M4 &N6
&P0 &R1 &S0 &T5 &U0 &Y1

S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002
S07=060 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000
S15=000 S16=000 S18=000 S19=000 S21=010 S22=017 S23=019
S25=005 S27=000 S28=008 S29=020 S30=000 S31=128 S32=002
S33=000 S34=000 S36=014 S38=000 S39=000 S41=000


USR 56K V.92 FAX modem settings: Red shows changes from default

B0 E1 F1 M1 Q0 V1 X1 Y0
BAUD=9600 PARITY=N WORDLEN=8
DIAL=TONE ON HOOK CID=0

&A1 &B0 &C1 &D0 &G0 &H0 &I0 &K1
&M4 &N6 &P0 &R1 &S0 &T5 &U0 &Y1

S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002
S07=060 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000
S15=000 S16=000 S18=010 S19=000 S21=010 S22=017 S23=019
S25=005 S27=000 S28=008 S29=020 S30=000 S31=128 S32=002
S33=000 S34=000 S35=000 S36=014 S38=000 S39=000 S40=001
S41=000 S42=000

Step 2: To alter the register, type the command prefix at, followed by the register letter and desired value. For example, if the modem had register f set to 0, register x set to 4 and register &N set to 0, those registers need to change.
You can change each register individually:
atf1 <enter>

 

[Laylobrown]

hyperterminal is

9600
8
none
1
and
vt100

 

[pandabear1]

check modem settings. Hyperterminal was ok as I missed the part where you said you can connect directly and it works ok.

 

[Laylobrown]

05-23-2007 17:42:58.218 - File: C:\WINDOWS\system32\tapisrv.dll, Version 5.1.2600
05-23-2007 17:42:58.218 - File: C:\WINDOWS\system32\unimdm.tsp, Version 5.1.2600
05-23-2007 17:42:58.218 - File: C:\WINDOWS\system32\unimdmat.dll, Version 5.1.2600
05-23-2007 17:42:58.218 - File: C:\WINDOWS\system32\uniplat.dll, Version 5.1.2600
05-23-2007 17:42:58.218 - File: C:\WINDOWS\system32\drivers\modem.sys, Version 5.1.2600
05-23-2007 17:42:58.218 - File: C:\WINDOWS\system32\modemui.dll, Version 5.1.2600
05-23-2007 17:42:58.218 - File: C:\WINDOWS\system32\mdminst.dll, Version 5.1.2600
05-23-2007 17:42:58.218 - Modem type: Standard 56000 bps Modem
05-23-2007 17:42:58.218 - Modem inf path: mdmgen.inf
05-23-2007 17:42:58.218 - Modem inf section: Gen556F
05-23-2007 17:42:58.218 - Matching hardware ID: moto1_gen
05-23-2007 17:42:58.406 - 9600,8,N,1, ctsfl=1, rtsctl=2
05-23-2007 17:42:58.421 - Initializing modem.
05-23-2007 17:42:58.437 - Send: AT<cr>
05-23-2007 17:42:58.562 - Recv: <cr><lf>OK<cr><lf>
05-23-2007 17:42:58.562 - Interpreted response: OK
05-23-2007 17:42:58.578 - Send: AT&FE0V1&C1&D2S95=47S0=0<cr>
05-23-2007 17:42:58.734 - Recv: <cr><lf>ERROR<cr><lf>
05-23-2007 17:42:58.750 - Interpreted response: Error
05-23-2007 17:42:58.750 - Session Statistics:
05-23-2007 17:42:58.750 - Reads : 15 bytes
05-23-2007 17:42:58.750 - Writes: 28 bytes
ATQ0V1E0 - OK
AT+GMM - COMMAND NOT SUPPORTED
AT+FCLASS=? - 0,1,2.0
AT#CLS=? - COMMAND NOT SUPPORTED
AT+GCI? - COMMAND NOT SUPPORTED
AT+GCI=? - COMMAND NOT SUPPORTED
ATI1 - E735
ATI2 - OK
ATI3 - U.S. Robotics Sportster 56000 Fax V4.1
ATI4 - U.S. Robotics Sportster 56000 Fax Settings...
B0 E0 F1 M1 Q0 V1 X4 Y0
BAUD=9600 PARITY=N WORDLEN=8
DIAL=TONE ON HOOK
&A1 &B0 &C1 &D2 &G0 &H0 &I0 &K1
&M4 &N0 &P0 &R1 &S0 &T5 &U0 &Y1
S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002
S07=060 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000
S15=000 S16=000 S18=000 S19=000 S21=010 S22=017 S23=019
S25=005 S27=000 S28=008 S29=020 S30=000 S31=128 S32=002
S33=000 S34=000 S35=000 S36=014 S38=000 S39=000 S41=000
S42=000

LAST DIALED #:
ATI5 - U.S. Robotics Sportster 56000 Fax NVRAM Settings...
Template Y0
DIAL=TONE B0 F1 M1 X4
BAUD=57600 PARITY=N WORDLEN=8
&A1 &B0 &G0 &H1 &I0 &K1 &M4 &N0
&P0 &R2 &S0 &T5 &U0 &Y1
S00=001 S02=043 S03=013 S04=010 S05=008 S06=002 S07=060
S08=002 S09=006 S10=014 S11=070 S12=050 S13=000 S15=000
S19=000 S21=010 S22=017 S23=019 S25=005 S27=000 S28=008
S29=020 S30=000 S31=128 S32=002 S33=000 S34=000 S35=000
S36=014 S38=000 S39=000 S41=000 S42=000

Strike a key when ready . . .
Template Y1
DIAL=TONE B0 F1 M1 X4
BAUD=38400 PARITY=N WORDLEN=8
&A3 &B1 &G0 &H2 &I2 &K1 &M4 &N0
&P0 &R1 &S0 &T5 &U0 &Y1
S00=001 S02=043 S03=013 S04=010 S05=008 S06=002 S07=060
S08=002 S09=006 S10=014 S11=070 S12=050 S13=000 S15=000
S19=000 S21=010 S22=017 S23=019 S25=005 S27=000 S28=008
S29=020 S30=000 S31=128 S32=002 S33=000 S34=000 S35=000
S36=014 S38=000 S39=000 S41=000 S42=000

STORED PHONE #0: 1847,9825092
#1: 9825092
#2:
#3:
ATI6 - U.S. Robotics Sportster 56000 Fax Link Diagnostics...
Chars sent 0 Chars Received 0
Chars lost 0
Octets sent 0 Octets Received 0
Blocks sent 0 Blocks Received 0
Blocks resent 0
Retrains Requested 0 Retrains Granted 0
Line Reversals 0 Blers 0
Link Timeouts 0 Link Naks 0
Data Compression NONE
Equalization Long
Fallback Disabled
Last Call 00:00:00
No Connection
ATI7 - Configuration Profile...
Product type US/Canada External
Options V32bis,V.34+,x2
Fax Options Class 1/Class 2.0
Line Options Caller ID, Distinctive Ring
Clock Freq 92.0Mhz
Eprom 256k
Ram 32k
FLASH date 3/8/97
FLASH rev 4.1.55
DSP date 3/8/97
DSP rev 10.3.55

 

[Laylobrown]

Okay I did an ATI4 (enter)

U.S. Robotics Sportster 56000 Fax Settings...

B0 E0 F1 M1 Q0 V1 X4 Y0
BAUD=2400 PARITY=N WORDLEN=8
DIAL=TONE ON HOOK

&A1 &B0 &C1 &D2 &G0 &H0 &I0 &K1
&M4 &N0 &P0 &R1 &S0 &T5 &U0 &Y1

S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002
S07=060 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000
S15=000 S16=000 S18=000 S19=000 S21=010 S22=017 S23=019
S25=005 S27=000 S28=008 S29=020 S30=000 S31=128 S32=002
S33=000 S34=000 S35=000 S36=014 S38=000 S39=000 S41=000
S42=000

LAST DIALED #:

OK

 

[paterson]

You need to change the modem settings. I copied your last reply and added where you need to look. The entries that are red are what you currently have and the green values are what you need to change to. I duplicated each line in bold from what Mitel says it should be. If you read above, you will see how to prepare the modem with dip switches and a serial connection to make the changes below. Good Luck!

Okay I did an ATI4 (enter)

U.S. Robotics Sportster 56000 Fax Settings...

B0 E0 F1 M1 Q0 V1 X4 Y0
B0 E1 F1 M1 Q0 V1 X1 Y0

BAUD=2400 PARITY=N WORDLEN=8
BAUD=9600 PARITY=N WORDLEN=8

DIAL=TONE ON HOOK
DIAL=TONE ON HOOK CID=0

&A1 &B0 &C1 &D2 &G0 &H0 &I0 &K1
&A1 &B0 &C1 &D0 &G0 &H0 &I0 &K1

&M4 &N0 &P0 &R1 &S0 &T5 &U0 &Y1
&M4 &N6 &P0 &R1 &S0 &T5 &U0 &Y1


S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002
S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002

S07=060 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000
S07=060 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000

S15=000 S16=000 S18=000 S19=000 S21=010 S22=017 S23=019
S15=000 S16=000 S18=010 S19=000 S21=010 S22=017 S23=019

S25=005 S27=000 S28=008 S29=020 S30=000 S31=128 S32=002
S25=005 S27=000 S28=008 S29=020 S30=000 S31=128 S32=002

S33=000 S34=000 S35=000 S36=014 S38=000 S39=000 S41=000
S33=000 S34=000 S35=000 S36=014 S38=000 S39=000 S40=001 Your print out does not have a S41. It should not matter.

S42=000
S41=000 S42=000

LAST DIALED #:

OK

**************************************
Insert Witty Signature Here.