Feature implementation
1. "LD 15 "
Set the Station Control Password length.
2. "LD 57 "
Define Remote Call Forward Flexible Feature Codes.
3. "LD 10"
Set the Station Control Password for analog (500/2500-type) telephones
and allow Call Forward.
4. "LD 11"
Set the Station Control Password for Meridian 1 proprietary telephones
and allow Call Forward.
LD 15
Prompt Response Description
REQ: CHG Change.
TYPE: FFC FFC gate opener.
CUST Customer number
0-99 Range for Large System and CS 1000E system.
0-31 Range for Small System and Media Gateway 1000B.
...
- SCPL 0-8 Station control password length (0-8).
Entering 0 disables the Remote Call Forward and the Electronic
Lock features.
A data dump and SYSLOAD are required to implement a
change in password length. Shorter passwords are filled with
leading zeros. Passwords that are too long have the leading
digits truncated.
- FFCS YES Change end of dialing digits in FFC.
- - STRL 1-3 Number of digits to indicate FFC end of a feature activation.
- - STRG (#), xxx 1 to 3 digits to indicate FFC end of a feature entry.
.
Feature implementation 537
LD 57
Prompt Response Description
REQ CHG Change.
TYPE FFC Flexible Feature Codes.
FFCT (NO) YES FFC Confirmation Tone (optional).
CODE RCFA Remote Call Forward Activate.
RCFA xx RCFA code
CODE RCFD Remote Call Forward Deactivate.
RCFD xx RCFD code.
CODE RCFV Remote Call Forward Verify.
RCFV xx RCFV code.
LD 10
Prompt Response Description
REQ: CHG Change.
TYPE: 500 Telephone type.
TN Terminal number
l s c u Format for Large System and CS 1000E system,
where l = loop, s = shelf, c = card, u = unit.
c u Format for Small System and Media Gateway 1000B where c =
card and u = unit.
SCPW xxx...x Station control password (0-8 digits as defined by prompt SCPL
in LD 15).
X Entering X deletes the password.
FTR CFW 4-(16)-23 Allow Call Forward and set forwarding DN length.
LD 11
Prompt Response Description
REQ: CHG Change.
TYPE: a...a Telephone type. Type ? for a list of possible responses.
TN Terminal number
l s c u Format for Large System and CS 1000E system,
where l = loop, s = shelf, c = card, u = unit.
c u Format for Small System and Media Gateway 1000B where c =
card and u = unit.
.
538 Remote Call Forward
Prompt Response Description
SCPW xxx...x
X
Station control password (0-8 digits as defined by prompt SCPL
in LD 15).
Entering X deletes the password.
KEY xx CFW 4-(16)-23 Assign Call Forward key (xx) and set forwarding DN length.
Feature operation
From any telephone within the system, simply lift the handset and use the
following procedures. From any telephone outside the system, first dial the
Direct Inward System Access (DISA) number for your system, wait for dial
tone, and dial any required passwords and Authorization Codes.
Step Action
1 Dial the Remote Call Forward Activate FFC.
2 Dial the Station Control Password for the telephone to be forwarded.
3 Dial the Prime DN of the telephone to be forwarded.
4 Dial the number to which calls will be forwarded.
5 Dial the end-of-entry digit(s) (defined in LD 15), if these digits plus
the number of digits in the forwarding DN are less than 24 digits. (If
you do not dial the end-of-entry digits, the forwarding DN is saved
but cannot be verified remotely.)
—End—
You will hear a confirmation tone after entering the main extension number,
telling you that the password and extension match. You will hear a second
special tone after dialing the end-of-entry digits, telling you that the
procedure was successful. If you hear a fast busy signal, hang up and
try again.
When entering the forwarding DN, you cannot enter more than 23 digits,
including the end-of-entry digits. If you attempt to enter a 24th digit, you
will hear an overflow tone.
If the forwarding DN plus the end-of-entry digits are not less than 24 digits,
hang up after dialing the forwarding DN. The DN is saved but cannot be
verified remotely.
To cancel Remote Call Forward:
• Dial the Remote Call Forward Deactivate FFC.
• Dial the Station Control Password for the telephone.
• Dial the Prime DN of the telephone.
To verify Remote Call Forward:
• Dial the Remote Call Forward Verify FFC.
• Dial the Station Control Password for the telephone.
• Dial the Prime DN of the telephone.
• Dial the number to which calls should be forwarded.
• Dial the end-of-entry digit(s).
If the number to which the telephone is forwarding calls does not match your
entry in step 4, you will hear a fast busy signal. If the numbers do match,
you will hear a confirmation tone after entering the forwarding number,
provided the confirmation tone is enabled in LD 57.
[©]
GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators
