Recall (Hook flash in USA?) back to dial tone on a FALC extn

[newrsoul]

Hi all,

I have what looks like 2 500 analogue extn's built the same (on the same FALC card too), in fact I think one was a copy of the other, on one I can issue a recall while in a call to get back to dial tone and make a second call, and on the other it seems to 'ignore' the tones and leaves me on the same original call.

I'm wondering if the FALC ports can be programmed for different types of recall, and one is on time break and the other on earth? Also can ports be programmed for loop calling and others earth calling?

The build Below extn 3040 does not work, and below this extn 3041 which does, I've been through them and can't see a difference!

DES 500
TN 016 0 01 00
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 3040 0 MARP
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 4
SGRP 0
RNPG 99
LNRS 16
XLST
SCI 0
SCPW
SFLT NO
CAC_MFC 0
CLS TLD DTN FBD XFA WTA THFD FND HTD ONS
LPR XRA AGRD CWD SWD PUA MWA RMMD SMWD LPD XHD SLKD CCSD LNA TVD
CFTD SFD MRD C6A CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUA DPUA CFXA ARHA OVDD AGTD CLTD LDTD ASCD
MBXD UDI RCC HBTD IRGD IAMD DDGA NAMA MIND
NRWD NRCD NROD SPKD CRD PRSD MCRD
EXR0 SHL SMSD ABDD CFHD DNDY DNO3
CWND USRD BNRD OCBD RTDD RBDD RBHD FAXD CNUD CNAD PGND FTTU
FDSD NOVD CDMR
RCO 0
PLEV 02
CSDN
AACS NO
MLWU_LANG 0
FTR CFW 16
FTR SSU 0010
FTR PHD
FTR RDL 16
DATE 10 FEB 2011

and 3041 which does

DES 500
TN 016 0 01 01
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 3041 0 MARP
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 4
SGRP 0
RNPG 99
LNRS 16
XLST
SCI 0
SCPW
SFLT NO
CAC_MFC 0
CLS TLD DTN FBD XFA WTA THFD FND HTD ONS
LPR XRA AGRD CWD SWD PUA MWA RMMD SMWD LPD XHD SLKD CCSD LNA TVD
CFTD SFD MRD C6A CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUA DPUA CFXA ARHA OVDD AGTD CLTD LDTD ASCD
MBXD UDI RCC HBTD IRGD IAMD DDGA NAMA MIND
NRWD NRCD NROD SPKD CRD PRSD MCRD
EXR0 SHL SMSD ABDD CFHD DNDY DNO3
CWND USRD BNRD OCBD RTDD RBDD RBHD FAXD CNUD CNAD PGND FTTU
FDSD NOVD CDMR
RCO 0
PLEV 02
CSDN
AACS NO
MLWU_LANG 0
FTR CFW 16
FTR SSU 0010
FTR PHD
FTR RDL 16
DATE 10 FEB 2011


Any idea's?

Thanks
Peter

 

[GHTROUT]

Can you adjust the flash timing on the phone/handset hardware? Is that what is different? Swap the phones with each other and see if the problem moves.

Find more at GHTROUT.com

 

[newrsoul]

Hi, Yes I've tried that and to no avail, it's as if the ports are programmed differently!?!

 

[newrsoul]

From the lack of responses I presume I'm asking something silly and that the 'recall method' is not defined on the card but fixed as 'time break', so I'm wondering about reseating the FALC card to see if it clears it's head? Are these cards hot swapable, do they redownload the config from the system when reinserted?

Thanks!