QSIG meridian => CISCO / Signalisation Voice Mail TOPCALL 2

[Nipponia]

hallo all.

I am new here in this forum.

I hope that anyone can help me by the following problem.

General Information:
meridian Option 11 Rls. 25.40
CISCO Call Manager 3.3
Gateway CISCO 3640
all DN's on the Call Manager are programmed as DSC on the meridian with an RLI ENTR0 to QSIG ROUT 9 (works perfect)

I have programmed a ROUT in ld 16 for a QSIG-Rout to a CISCO Gatway 3640
On the CISCO i programmed the lines to the voice mail system TOPCALL.
The QSIG Route work properly between meridian and CISCO.

The only thing which doesn't work is, that the Voice Mail TOPCALL can't recognice the signalisation of the meridian phone (internal number with 4 digits) which has activated call forward to the main number of the voice mail

Can it be, that the ROUT on the meridian is not correct (see ld 16 / rdb / rout 9)
RCLS EXT => is there a success to change to RCLS NO ?

It is possible to call the main voice mail number from a meridian phone ... just there is something wrong with the signalisation of the internal number (4 digit)

Thanks to give me an idea to solve this problem.

ROUT 9
======
>ld 21
REQ: prt
TYPE: rdb
CUST 0
ROUT 9

TYPE RDB
CUST 00
DMOD
ROUT 9
DES QSIG_CISCO
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
IDEF NET
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC ESGF
SBN NO
PNI 00001
NCNA NO
NCRD NO
CTYP UKWN
INAC YES
ISAR NO
CPFXS YES
DAPC YES
TBL 0
INTC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB NO
STEP
ACOD 110509
TCPP NO
TARG 01 02
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 4096
NRD 9088
DDL 70
ODT 4096
RGV 128
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG YES
NDRI 01
CDR YES
INC YES
LAST NO
QREC NO
OAL NO
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
RACD NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 1617110 9
SGRP 0
AACR NO

 

[iptuser]

Is the issue that when the call goes to the Top Call voice mail it is not recognised? what do you get? We had an issue where the Topcall would not recognise the CLI of the forwarding extension. They have to forward to the main VM number and also add the extension number in forward command

wayne

 

[Nipponia]

Hallo wayne67
thanks for reply

yes, when the call goes to the Top Call (from meridian, QSIG ROUT 9, gateway, CISCO Call Manager to Top Call)

What do I get?
Top Call ask for the Password and doesn't start with my announcement. In Top Call my user is correct. It works if I forward the call from the CISCO Phone to the VM Number of Top Call.

 

[nortic]

check following

Is the steering code a DSC ,if so is DSP set for DN
the default is LOC witch sends the LOC CODE entered in
CDB under NET , as a prefix in the display or CLID

LD 87
REQ PRT
CUST 0
FEAT CDP
DSC XXXX VOICE MAIL DN
DSP (LOC) CHANGE TO DN




YOU CAN TURN ON DCHANNEL MESSAGE IN LD 96 TO SEE IF THIS IS
HAPPENING IT WILL PROBABLY SHOW LOC CODE AND DN
AS A UNKNOWN DN

DCH 15 OMSG SETUP REF 00000014 CH 51 20 TOD 16:21:28
PROGRESS: CALL IS NOT END TO END ISDN
CALLING #:3650 NUM PLAN: PRIVATE
CALLED #:6401300

INSTEAD OF 1300 VOICE MAIL SEES 6401




BY THE WAY HERE IS AN ALTERNATE WAY TO SET UP NORTEL TO GATEWAY WITHOUT QSIG

DCH AND RDB FOR CISCO ROUTER

ADAN DCH 9
CTYP MSDL
DNUM 15 (MSDL CARD DEVICE NUMBER SET USING THUMB SWITCH ON CARD
PORT 3
DES cisco
USR PRI
DCHL 23
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC SL1
SIDE NET
SEMT 1
CNEG 1
RLS ID 16
RCAP ND2
T200 3
T203 10
N200 3
N201 260
K 7


TYPE RDB ROUTE DATA , IF NORTEL IS USING PNI'S IN NETWORK OF CDB USE 1
CUST 00
ROUT 7 YOUR CHOICE
DES VOIP
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
DTRK YES
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
NCNA NO YOUR CHOICE
NCRD YES
CHTY BCH
CTYP CDP OR UKWN
INAC NO
ISAR NO
DAPC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 8007
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR YES
INC YES
LAST NO
QREC YES
OAL YES
AIA NO


PAGE 002

OAN NO
OPD NO
NATL YES
MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ YES
OHQT 00
CBQ YES
NDIG 02
AUTH NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

SET CISC0 GATEWAY INTERFACE AS FOLLOWS


interface Serial3/0:23
no ip address
ip mroute-cache
no logging event link-status
isdn switch-type primary-dms100
isdn incoming-voice voice
isdn flip-chan-flag
no cdp enable


HOPE THIS HELPS, NORTIC

 

[nortic]

did you get this problem resolved?


nortic

 

[Nipponia]

hi nortic

sorry for late reply.

yes, we use steering code DSC, but we already set the DSP to DN before.
May it help to change RCLS in the QSIG Route from EXT to INT?