PTP circuit - CS1000e <---> Sonus SBC 1000

[TelecomGuyUT]

Hey Guys,

I have a PRI circuit up between Rls a 5.5 CS1000e and a Sonus SBC 1000. We will be using it for a connection to and from MS Lync pretty soon. I have configuring the route and the D-channel as TIE and DID using QSIG. I'm using MSGI/MSGO in LD 96 to watch the D-channel messages and the call from the SBC to the PBX is being manipulated for some reason. The call routes to the main number of the office (menu system in CallPilot) I just can't figure out why. (I haven't tried calling the other direction yet, because Lync isn't ready) See below for my current config and a call example. Any help would be greatly appreciated!

ROUT 2

TYPE RDB
CUST 00
ROUT 2
DES SONUS
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISIG
SBN NO
PNI 00001
NCNA NO
NCRD NO
CHTY BCH
ISAR NO
CPFXS YES
DAPC NO
INTC NO
MBXR NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 6202
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO
NDNO
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
IENB 5
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST YES
QREC YES
OAL YES
AIA YES
OAN YES
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO


DES SONUS
TN 033 01 VIRTUAL
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 2 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 25 OCT 2013


ADAN DCH 33
CTYP TMDI
MG_CARD 000 0 04
PORT 1
DES SONUS
USR PRI
DCHL 33
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC ISIG
ISDN_MCNT 300
CLID OPT1
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP NCT COLP
MBGA NO
OVLR YES
DIDD 0
OVLS YES
OVLT 0
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

DCH 33 UIPE_IMSG CC_SETUP_IND REF 00001700 CH 33 15 TOD 12:04:12 CK FB03FF9E
CALLED #:[highlight #FCE94F]801319XXXX[/highlight] NUM PLAN: UNKNOWN TON: UNKNOWN

DCH 33 UIPE_OMSG CC_PROCEED_REQ REF 00009700 CH 33 15 TOD 12:04:12 CK FB03FF9E

DCH 33 UIPE_OMSG CC_ALERT_REQ REF 00009700 CH 33 15 TOD 12:04:14 CK FB04092A

DCH 33 UIPE_OMSG CC_SETUP_RESP REF 00009700 CH 33 15 TOD 12:04:14 CK FB040E2C
CONNECT #:[highlight #FCE94F]801437XXXX[/highlight] NUM PLAN: E164 TON: NATL

DCH 33 UIPE_IMSG CC_SETUPCOMP_IND REF 00001700 CH 33 15 TOD 12:04:14 CK FB040EA2

DCH 33 UIPE_IMSG CC_DISC_IND REF 00001700 CH 33 15 TOD 12:04:26 CK FB04749F
CAUSE: #31 - NORMAL UNSPECIFIED

DCH 33 UIPE_OMSG CC_RELEASE_REQ REF 00009700 CH 33 15 TOD 12:04:26 CK FB04749F

DCH 33 UIPE_IMSG CC_RELEASE_CONF REF 00001700 CH 33 15 TOD 12:04:26 CK FB0474F5

 

[Splic3d]

Is 801319XXXX defined on the CS100 somewhere. Just to varify.

http://www.i3techgroup.com

If its not working, get a bigger hammer!

Avaya/Nortel/NEC/Asterisk/Access Control/CCTV/DSX/Acti/UCx

 

[TelecomGuyUT]

Hi Splic3d,

Its really not specifically. Its a local call, so its just at the NXX level.

FEAT net
TRAN ac1
TYPE npa

NPA 1801

NPA 1801
RLI 4
DMI 42
LDID 437XX

LDID 437XX

LDID 437XX

SDRR LDID CODES = 3
ITEI NONE


MEM AVAIL: (U/P): 98328190 USED U P: 5652998 288633 TOT: 104269821
DISK SPACE NEEDED: 472 KBYTES
REQ

prt
CUST 0
FEAT net
TRAN ac1
TYPE nxx

NXX 319

NXX 319
RLI 0
SDRR NONE
ITEI NONE

 

[Splic3d]

The nxx and npa will be associated with the out calling, but to receive a call, the digits need to land somewhere. Or am I miss reading what you are saying ?

http://www.i3techgroup.com

If its not working, get a bigger hammer!

Avaya/Nortel/NEC/Asterisk/Access Control/CCTV/DSX/Acti/UCx

 

[TelecomGuyUT]

You are correct. I sending it to an IDC table, but I got the same thing.

 

[Splic3d]

Just another guess. Print your LDN_DATA. The switch will look for the number of incoming digits as associated with with one of the LDN entries.

http://www.i3techgroup.com

If its not working, get a bigger hammer!

Avaya/Nortel/NEC/Asterisk/Access Control/CCTV/DSX/Acti/UCx

 

[TelecomGuyUT]

I got it.

It was mad about the QSIG for some reason. I tore down the config and rebuilt as NI2 and I can get calls to complete.

Here is what I ended up with:

TYPE RDB
CUST 00
ROUT 2
DES SONUS
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00001
NCNA NO
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 6202
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 1 *
NDNO 1
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
IENB 5
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST YES
QREC YES
OAL YES
AIA YES
OAN YES
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO


ADAN DCH 33
CTYP TMDI
MG_CARD 000 0 04
PORT 1
DES SONUS
USR PRI
DCHL 33
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID 25
RCAP COLP NDS
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO


DES SONUS
TN 033 01 VIRTUAL
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 2 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 25 OCT 2013