Programming trunks?

[89549]

Hello, I need some help. The Nortel switch I received was programmed for a pri. This is a new install at a bank and we were told the pri would not be in for another week. I have purchased two universal trunk cards and tried to program them to the switch. I have tried to build a RDB & TDB but I can’t call out or no ringing comes in, I have dial tone at the card. I searched the form on how to build a RDB(LD 16) and a TDB(LD 14). Am I missing something? Could someone give me an example of a loop start trunk ( I have 9 analog lines) ringing to a group of phones that also have access to these lines. This would save my butt. Thankyou to anyone who replies

 

[technickelone]

can you print out what you built and paste it.

 

[89549]

I don't have a printer hooked up to the switch. Any ideas?
Thanks

 

[dnc16]

LOL!!! Good luck running a PBX!

 

[phonedoc]

you didnt mention if these were DID. You are sure they are loop start?

 

[techman3030]

Do you have a modem for outside access? If so dial into it with hyperterminal or procomm and post what you have programmed. If it was already programmed to go out this pri route then that is where it is trying to go.

 

[johnpoole]

if you put a butt set on the demark, doyou get dial tone? if so they are loop start


DES 411
TN 008 0 11 00
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK ANLG
NCOS 4
RTMB 66 1
NITE
SIGL LOP... if they are ground start GRD)
SUPN NO
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD
P10 NTC


john poole
bellsouth business
columbia,sc

 

[johnpoole]

here is the route


DES 411
TN 008 0 11 00
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
TRK ANLG
NCOS 4
RTMB 66 1
NITE
SIGL LOP
SUPN NO
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD
P10 NTC
TKID
DATE 17 DEC 2004 ****
OVL000
>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 66

TYPE RDB
CUST 00
ROUT 66
DES 411
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 7705
CPP NO
TARG 01
CLEN 1
BILN NO
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 3
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512

IENB 5
TFD 0
LEXT 100
VGD 6
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DRNG NO
CDR NO
MUS NO
MR NO
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0


PAGE 002

FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR


if these are pots lines, answer auto yes and on the trunks put a dn at atdn, that will be the answer point

john poole
bellsouth business
columbia,sc

 

[89549]

Thanks everyone for your help. Thanks John for the example, it was very helpful.

Tony

 

[dladuron]

can anyone tell me what LD code is used to start programming the Line.

I have recently changed from ground loop to loop start and need to reconfig the two pots lines coming into my Option ll

Thanks