Programming 11c for Dial Out 1

[nortelephoneguy]

I've been a Nortel Tech for over 8 years (certified and all) but I've only worked on the larger systems. I am now trying to program an 11c to dial out. It is a backup system to the 81c and I 'borrowed' a PRI from the 81c to accommodate the 11c. The problems are:
1 - I can't seem to break the PRI channels out of 'MBSY' mode. I'm using 'SL1' @ IFC.
2 - I cannot seem to get 'outside tone' when dialing my access code ('9'). Where would I check for proper programming of code?

* Just for the record - the PRI was programmed as a DID on the 81c and I am using it as a TIE on the 11c.
Thanks for any help.

 

[johnpoole]

i would make it match on both ends, a iao did works, and when you define ac1 you either allow or deny dial tone,.. as far the msby, a point to point pri should come up clean, make sure you dis the msdl and/or the tmdi after any d channel change, when you enl dch x fdl, those change take effect, heres a pri i have going back to a opt 11, if you need the 11 end let me know

DES  PARKRIDGE
TN   049 01
TYPE TIE
CDEN SD
CUST 0
TRK  PRI
PDCA 1
PCML MU
NCOS 6
RTMB 49 1
B-CHANNEL SIGNALING
TGAR 1
AST  NO
IAPG 0
CLS  UNR DTN WTA LPR APN THFD HKD
     P10 VNL
TKID
DATE 27 DEC 2004


NACT
REQ: prt
TYPE: ****
OVL000
>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 49

TYPE RDB
CUST 00
ROUT 49
DES  PARKRIDGE
TKTP TIE
NPID_TBL_NUM   0
ESN  NO
CNVT NO
SAT  NO
IDEF NET
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
    MODE PRA
    IFC  SL1
    PNI  00001
    NCNA YES
    NCRD YES
    TRO  NO
    CHTY BCH
    CTYP CDP
    INAC NO
    ISAR NO
    DAPC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 8205
TCPP NO
TARG 05 06
CLEN 1
BILN NO
OABS
INST
IDC  NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF  512
     OGF  512
     EOD  13952
     NRD  10112
     DDL  70
     ODT  4096
     RGV  640
     GRD  896
     SFB  3
     NBS  2048
     NBL  4096

     IENB  5


PAGE 002

     TFD  0
     VSS  0
     VGD  6
DRNG NO
CDR  YES
INC  YES
LAST YES
QREC NO
OAL  YES
AIA  NO
OAN  YES
OPD  NO
CDRX NO
NATL YES
VRAT NO
MUS  YES
MRT  10
RACD NO
EQAR NO
FRL  0 0
FRL  1 0
FRL  2 0
FRL  3 0
FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0
OHQ  NO
OHQT 00
CBQ  NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART  0
SGRP 0
AACR NO

REQ: end
>ld 22
PT2000

REQ  prt
TYPE ****
OVL000
>ld 96
DCH000
.stat dch
DCH 003 : OPER EST   ACTV  AUTO         DES : ARDENCO
DCH 004 : OPER EST   ACTV  AUTO         DES : SENATE125
DCH 029 : OPER EST   ACTV  AUTO         DES : SENATE29
DCH 044 : OPER EST   ACTV  AUTO         DES : SENATE44
DCH 049 : OPER EST   ACTV  AUTO         DES : PARKRIDGE
DCH 100 : OPER EST   ACTV  AUTO         DES : Cisco
DCH 101 : OPER EST   ACTV  AUTO         DES : CiscoBaptist
DCH 156 : OPER EST   ACTV  AUTO         DES : BS_LD
DCH 157 : OPER EST   ACTV  AUTO         DES : BS_LD
.****
OVL000
>ld 22
PT2000

REQ  prt
TYPE adan dch 49

ADAN     DCH 49
  CTYP MSDL
  GRP  1
  DNUM 10
  PORT 2
  DES  PARKRIDGE
  USR  PRI
  DCHL 49
  OTBF 32
  PARM RS422  DTE
  DRAT 64KC
  CLOK EXT
  NASA NO
  IFC  SL1
  SIDE NET
  SEMT 1
  CNEG 1
  RLS  ID  3
  RCAP ND2
  MBGA NO
  OVLR NO
  OVLS NO
  T200 3
  T203 10
  N200 3
  N201 260
  K

john poole
bellsouth business
columbia,sc

 

[nortelephoneguy]

Thanks Johnpoole. Realize - also - that the 11c is a standalone system and will not be connected to the 81c. I am interested in seeing the 11c programming as well.
Thanks again for such a quick response!

 

[johnpoole]

here's the far end stand alone opt 11, older rls,

REQ: prt
TYPE: tnb
TN   2 1
DATE
PAGE
DES

DES  TIE_HOSP
TN   002 01
TYPE TIE
CDEN SD
CUST 0
TRK  PRI
PDCA 1
PCML MU
NCOS 0
RTMB 2 1
B-CHANNEL SIGNALING
TGAR 1
AST  NO
IAPG 0
CLS  CTD DTN CND WTA HPR APN THFD HKD
     P10 VNL
TKID
DATE 22 OCT 2003


NACT
REQ: end
>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 2

TYPE RDB
CUST 00
DMOD
ROUT 2
DES  TIE_HOSP
TKTP TIE
NPID_TBL_NUM   0
ESN  NO
CNVT NO
SAT  NO
RCLS INT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
    MODE PRA
    IFC  SL1
    PNI  00001
    NCNA YES
    NCRD YES
    TRO  NO
    CHTY BCH
    CTYP UKWN
    INAC NO
    ISAR NO
    DAPC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 8210
TCPP NO
TARG 05 06
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
     OGF 512
     EOD 13952
     NRD 10112
     DDL 70
     ODT 4096
     RGV 640
     GRD 896
     SFB 3
     NBS 2048
     NBL 4096
     TFD 0
DRNG NO
CDR  NO
MUS  NO
FRL  0 0
FRL  1 0
FRL  2 0


PAGE 002

FRL  3 0
FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0
OHQ  NO
OHQT 00
CBQ  NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART  0
SGRP 0
AACR NO

REQ: end
>ld 22
PT2000

REQ  prt
TYPE adan dch 4

ADAN     DCH 4
  CTYP TMDI
  CARD 02
  PORT 1
  DES  TIETOHOSP
  USR  PRI
  DCHL 2
  OTBF 127
  PARM RS232  DTE
  DRAT 64KC
  CLOK EXT
  NASA NO
  IFC  SL1
  SIDE USR
  CNEG 1
  RLS  ID  25
  RCAP ND2
  MBGA NO
  OVLR NO
  OVLS NO
  T200 3
  T203 10
  N200 3
  N201 260
  K

quick point, if you always match your card/loop with your route and dch, trouble shooting will get a little quicker. very few things bother me quicker then software that don't make sense

john poole
bellsouth business
columbia,sc

 

[tekice]

you need a different pri card from the one that is in the option 81c not iterchangeable.

 

[nortelephoneguy]

Ok - I'm doing something wrong - lol. Now my D-channel is coming up with a 'wrong mode' message. My 'side' in ld 17 is set to 'user'. There must be something wrong with either my tmdi or dch config. I was under the assumption that a new install on an 11c stand alone system would be breeze. Boy! Was I wrong. All I want is outside dial tone............Telecom 101 - right? Lol. I'm still listening.

 

[nortelephoneguy]

I just noticed that your 'pni''s were set to 0001 on both ends - is there any signifigance to this?

 

[q4ayaz]

Please check the card comptibility between the 81C nad 11C or check the part no.

 

[johnpoole]

the private number id, must match on each end, never tried one that wasn't but they do match.. if your still haveing trouble with this, post the trouble discription, lcnt lcnt tables etc. for any pri trouble, always do a loop back to your switch. after you enll the loop in 60, withen 2 (?) minutes the d will est, then will rls wronge mode. that is due to the side prompt, one end needs to be set to usr the other net. each one should react almost the same way. also make sure that after ANY change on the d, dis msdl x in load 96 and enl msdl x fdl to write that change to the card. those changes do not take on the fly. the card has a cpu and ram, it needs to be updated to see the change..

john poole
bellsouth business
columbia,sc