Program paging trunk for CS1000 for Valcom VIP 811 1

[TIMBWI]

When I dial my ACOD I get the valcom dialtone then a fast busy. When I put a butt set on it and go off hook it works. What are the propoer settings for the route and trunk member

 

[EddieDuece]

Heres my page route. Hope it helps.

TYPE RDB
CUST 00
ROUT 5
DES PAGING
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG OGT
RANX NO
SRCH LIN
STEP
ACOD 74
CPP NO
TARG 01 02 04 06
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512

IENB 5
TFD 0
LEXT 100
VGD 6


PAGE 007

SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR NO
MUS NO
MR NO
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

 

[TIMBWI]

How about the trunk

 

[EddieDuece]

Trunk info....

DES PAGING
TN 012 0 01 05
TYPE COT
CDEN 8D
CUST 0
XTRK EXUT
FWTM NO
TIMP 600
BIMP 3COM
AUTO_BIMP NO
TRK ANLG
NCOS 0
RTMB 5 1
NITE
SIGL LOP
SUPN NO
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD
P10 NTC
TKID
DATE 9 DEC 2004

 

[TIMBWI]

Thanks for the input I will give it a try

 

[johnpoole]

another thing to check "01 02 04 06" i assume that the station does not match.. and go to ld 49 and ini nfas table 0 as an alow table.. when you acod then need a digit,

FRL  0 0
FRL  1 0
FRL  2 0
FRL  3 0
FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0

we almost never use ld 49 for that anymore, but it does come into play after acod access


john poole
bellsouth business
columbia,sc

 

[jamie2]

Thats the first thing I would check. Make sure your tgar of the phone isn't matching the Targ of the route.

After you get it going, it wouldn't hurt to set your TFD value.

 

[johnpoole]

that's a good point, do a change on the route data block as enter yes at the crtl promopt then enter tfd 120, that will give you a hard rls after 2 minutes.. loop start needs that so it will not lopck in the busy state. i would test it without the targs.. when i install one new i enter x1 at that prompt then add targs after the fact

john poole
bellsouth business
columbia,sc