Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Problem with E-1 with DTI2 Card, without DCH

Status
Not open for further replies.

malloryknox

Technical User
Mar 3, 2004
13
GB
Hello All,

I need some help about a new installation in our customer in south America.....so far away :(

That´s the point.
We just installed a new E-1 circiut with a DTI2 card, but it doesn´t work. It´s status is NNC (No New Calls)
I have no experience wiht DTI2 card, I usually install PRI2 card with D-CHANNEL etc.
The system has not MDSL Card....

DTI2 LOOP 21 - ENBL
REF CLK: DSBL
SERVICE RESTORE: YES
ALARM STATUS: NNC
CH 01 - IDLE DID VOD CH 02 - IDLE DID VOD
CH 03 - IDLE DID VOD CH 04 - IDLE DID VOD
CH 05 - IDLE DID VOD CH 06 - IDLE DID VOD
CH 07 - IDLE DID VOD CH 08 - IDLE DID VOD
CH 09 - IDLE DID VOD CH 10 - IDLE DID VOD
CH 11 - IDLE DID VOD CH 12 - IDLE DID VOD
CH 13 - IDLE DID VOD CH 14 - IDLE DID VOD
CH 15 - IDLE DID VOD CH 16 - IDLE DID VOD
CH 17 - IDLE DID VOD CH 18 - IDLE DID VOD
CH 19 - IDLE DID VOD CH 20 - IDLE DID VOD
CH 21 - IDLE DID VOD CH 22 - IDLE DID VOD
CH 23 - IDLE DID VOD CH 24 - IDLE DID VOD
CH 25 - IDLE DID VOD CH 26 - IDLE DID VOD
CH 27 - IDLE DID VOD CH 28 - IDLE DID VOD
CH 29 - IDLE DID VOD CH 30 - IDLE DID VOD
.

LOOP 21


REQ PRT
TYPE CEQU

CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ
REMQ
SUPL V000 N072 V096 N100
V248 N252
SUPC
SUPF
DDCS MG_CARD
DTCS
XCT
CONF
MGTDS IPMG IPMG_TYPE
124 000 0 MGC
MGCONF IPMG PORTS IPMG_TYPE
125 000 0 30 MGC
MFSD * 124
APVL
DTI2 MG_CARD
021 000 0 02
MISP MG_CARD
SYNM 0
EXT0 3PE
EXT1 3PE
MCFN 011 MB


CLOCK REFENCE

REQ prt
TYPE dti2
FEAT syti
MAND 15
NCSD 15
OSGD 15
OOSC 5
PERS 100
DBNC 10

MGCLK 0 0 2
PREF 0 0 2
SREF
CCGD 15
CCAR 15
EFCS NO

LOOP

REQ PRT
TYPE DTI2
FEAT LPTI
LOOP 21

CDTI2 NO
P DIGT (S) PXXX
P METR (R) UNUSED
PPMD NO
SASU 1920
MFAO NO
SZNI YES
LCLB NO
UCFS 1101
BPV 250 3 S 2 S 1 S 0
FAP 250 3 S 2 S 1 S 0
SLP 250 3 S 2 S 1 S 0
GP2 250 3 S 2 S 1 S 0


ROUT

TYPE RDB
CUST 00
ROUT 69
DES CONSULT
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
DGTP DTI2
ISDN NO
DSEL VOD
PTYP DCO
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 44
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
MFC NO
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 3840
RGV 640
FLH 510
GTO 896
GTI 896
SFB 3
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
OPCB NO
DDO NO
DRNG NO
CDR YES


PAGE 002

INC YES
LAST NO
QREC NO
OAL YES
AIA YES
OAN YES
OPA YES
OPD YES
NDP EXC 0
CDRX NO
CCO NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS YES
MRT 40
MR NO
PANS YES
MANO NO
EQAR NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
PRDL NO
DNSZ 0
RCAL NO
MCTS NO
ALRM NO
BTT 30
ACKW NO
ART 0
OPDL 0
PECL NO
DCTI 0
TIDY 44 69
NADT 0
SGRP 0
FRIN NO
RRBS NO
RLSM 0
CCB NO
CCBA NO
ARDN NO
AACR NO

TRUNK

TN 021 01 VIRTUAL
TYPE DID
CUST 0
TRK DTI2
SICA 2
PDCA 1
PCML A
NCOS 0
RTMB 69 1
NITE
AST NO
IAPG 0
CLS UNR MFC CNA ECD WTA LPR APN THFD SPCD
P10
MFL 0
MFPD NO
TKID
DTCR NO
AACR NO
DATE 22 SEP 2010


That´s the telecom provider information:

clock Mode MASTER
Monitor Link state DISABLE
Line Coding HDB3
Line Framing NO-CRC4
Channel Range 1-30
Encoding Scheme G.711 a-Law
Line Signaling Protocol Q.421 2BITS SIGNALING
Register Signaling Protocol MFC/R2



 
You've got an R2 circuit. They are not easy. You will need to define and assign MFC registers and define the R2 tables.
 
NTP NN43001-284 Multi-Frequency Fundamentals. That's your guide.
 
It doesn´t work :(
Any ideas
I´ve configured the tables like this


TYPE R2MF
ICOG ICT
MAXT 1
TBNO 1
EECD 1
SMFC NO
SCNT NO
CNDR NO
LVNO 1

RECV 1 DGT1
2 DGT2
3 DGT3
4 DGT4
5 DGT5
6 DGT6
7 DGT7
8 DGT8
9 DGT9
10 DGT0
11 HTDM
12 ECNI
15 EODL

XMIT NEXT 1
TERM 6
COMP 3
CONG 4
CCNI 5
SCNI 9
FAIL 15

TYPE R2MF
ICOG ICT
MAXT 1
TBNO 1
EECD 1
LVNO 2

RECV 1 NOPR
2 PRIO
3 NOPR
5 OPER
6 NOPR
7 REST
8 NOPR
9 PRIO
10 OPER
11 NOPR
12 NOPR
13 NOPR

XMIT IDLE 6
BUSY 3
CONG 4
VACC 5
OUTT 8
FAIL 9



And the route

TYPE RDB
CUST 00
ROUT 69
DES CONSULT
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
DGTP DTI2
ISDN NO
DSEL VOD
PTYP DCO
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 44
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
MFC R2MF
INDMF NO
MFCI 1
R2MD NO
SGL NO
BSSU NO
MFCO 1
OPP NORM
SWP NORM
ICIS YES
ICNP UKWN
ICNT UKWN
ICPS YES
OGIS YES
PTUT 0
TIMR MFC 12032
MFO 0
MFID 0
ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 3840
RGV 640
FLH 510
GTO 896


GTI 896
SFB 3
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
OPCB NO
DDO NO
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA YES
OAN YES
OPA YES
OPD YES
NDP EXC 0
CDRX NO
CCO NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS YES
MRT 40
MR NO
PANS YES
MANO NO
EQAR NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
TDET NO
TTBL 0
PNNC NO
ATAN NO
OHTD NO
PLEV 2
OPR NO
RCAL NO
MCTS NO
ALRM NO
BTT 30
ACKW NO
NCNI 0
CNIE NO
CNIT NO
CTAT NO
ART 0
OPDL 0
PECL NO
DCTI 0
TIDY 44 69
NADT 0
SGRP 0
FRIN NO
RRBS NO
RLSM 0
CCB NO
CCBA NO
ARDN NO
AACR NO
 
Do you have a MFC register defined?

REQ: prt
TYPE: mfc
TN
CDEN
DATE
PAGE

TN 004 0 07 00 VIRTUAL
TYPE MFC
CDEN 8D
DATE 19 FEB 2011

This is a outgoing MFC table that we used in Mexico.

>*ld 94
MFCT000
MEM AVAIL: (U/P): 94853591 USED U P: 8539365 259393 TOT: 103652349
DISK SPACE NEEDED: 307 KBYTES
REQ prt
TYPE r2mf
ICOG ogt
TBNO

TYPE R2MF
ICOG OGT
MAXT 2
TBNO 2
SET 1
ATT 1
TIE 6
NTT 6
EECD 2
SMFC NO
SCNT NO
CNDR NO
LVNO 1

RECV 1 NEXT
2 TNM1
3 COMP
4 CONG
5 SCAT
6 TERM
7 TNM2
8 TNM3
9 SCNI
10 TFST
11 TNXT
15 FAIL

XMIT DGT1 1
DGT2 2
DGT3 3
DGT4 4
DGT5 5
DGT6 6
DGT7 7
DGT8 8
DGT9 9
DGT0 10
ECNI 12
EODL 15
HTDM 11

TYPE R2MF
ICOG OGT
MAXT 2
TBNO 2
SET 1
ATT 1
TIE 6
NTT 6
EECD 2
LVNO 2

RECV 1 IDLE
2 BUSY
3 BUSY
4 CONG
5 VACC
8 OUTT
9 FAIL

XMIT NOPR 2
OPER 2
REST 7

any chance to get the customer to switch to ISDN? We have systems all through South America. Venezuela is the only country where we cannot get ISDN, and it is our last R2 trunk.
 
Thanks HWKING, I think it´s very complicated to ask any change to telecom provider.
This is my MFC configuration:

TN 000 0 15 00 VIRTUAL
TYPE MFC
CDEN 8D
DATE 30 OCT 2012

TN 000 0 15 01 VIRTUAL
TYPE MFC
CDEN 8D
DATE 21 MAR 2011

TN 000 0 15 02 VIRTUAL
TYPE MFC
CDEN 8D
DATE 21 MAR 2011

TN 000 0 15 03 VIRTUAL
TYPE MFC
CDEN 8D
DATE 21 MAR 2011


.stat 0 0 15
00 = UNIT 00 = IDLE MFC
01 = UNIT 01 = IDLE MFC
02 = UNIT 02 = IDLE MFC
03 = UNIT 03 = IDLE MFC

An aditional information, we have a Yellow Alarm in the card, it´s NEA Alarm. It could be a conectivity issue, like conectors etc ?????
 
Good news! but the operation is almost right. The telecom provider was wrong. They made some changes in the infraestructure.

The situation is, we can send outgoing calls 100%, but we have 40% of bad incoming calls.

Please, Could you give me an example of MFC incomunig table?

Thanks a lot.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top