Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Problem with call forwarding HIPATH 4000 V6 2

Status
Not open for further replies.

youfo007

Technical User
Nov 4, 2012
50
MA
hello,

We have HiPath 4000 V6
I have problem with call forwarding

Situation 1:

I receive call from external user (ex. another trunk isdn s2conn) and transfer to another our local user. I receive no answer or busy tone.

Situation 2

I receive call from external user (ex. another trunk isdn s2conn) and I'd like transfer to our other external user through a link. I receive no answer or busy tone.

When I receive no answer or busy tone, the situation remains like this.

I tried to check several parameter (feasu, ziel, COS1, cos2, lcosv1, zand) and the problem still persists.

this is the command I use:


ADD-ACTDA:STN,7854,FWD,STATIONV,CFU,GEN,VCE,6312548;





thanks for any advice

best regards
 
Hi,
Can you first check the following:

Can you dial 6312548 from extension 7854


Then make a call to a speaking clock or similar, put it on hold and try and transfer it out to an external user, does it work?
 
yes I tried it all but I found some notes:

the extension 7854 can dial 6312548, 7xxx can dial 631xxxx, I note here that the number does not appear on 631xxxx which is a CUCM, it gives me * xxx * something like that.

for the transfer, it works very well and no problem in any way.

for forwarding I tried a local forward and it worked.

it remains for me the external forwarding.


 
Years ago an Oil worker from another continent visited a local company.
I got a call from the company manager one morning to call in.
The oil worker had diverted his phone to an African number, went to his hotel room and made a local call back to his temporary desk phone and then he was connected to the African number.

Anyhow you need to allow external diversions/forwarding in COSSU COS as follows:



ADD-COSSU:,12,,,,,,,,"STD COS WITH INTNL FWDING ONLY ";
CHANGE-COSSU:COS,12,TA&TNOTCR&CDRS&CDRC&CDRIND&CDRINT&COSXCD&MB,,,,,,,;
CHANGE-COSSU:COS,12,DATA&VCE&TTT&ANSYN&CW&UUS3&CTLS&ACTMAN,,,,,,,;
CHANGE-COSSU:COS,12,,TA&TNOTCR&BASIC&TTT&SUBMSN&MSN&MULTRA&KIESIG,,,,,,;
CHANGE-COSSU:COS,12,,UUS1IM&UUS3&ACTMAN,,,,,,;
CHANGE-COSSU:COS,12,,,TA&TNOTCR&DSM&BASIC&TTT&SUBMSN&MSN&MULTRA,,,,,;
CHANGE-COSSU:COS,12,,,KIESIG&UUS1IM&UUS3&ACTMAN,,,,,;

ADD-COSSU:,13,,,,,,,,"STD COS WITH EXTNL FWDING ALLOWED";
CHANGE-COSSU:COS,13,TA&TNOTCR&CDRS&CDRC&CDRIND&CDRINT&COSXCD&MB,,,,,,,;
CHANGE-COSSU:COS,13,DATA&CFNR&VCE&FWDNWK&TTT&CFB&FWDFAS&FWDDIR,,,,,,,;
CHANGE-COSSU:COS,13,CFSWF&CW&UUS3&ACTMAN,,,,,,,;
CHANGE-COSSU:COS,13,,TA&TNOTCR&BASIC&TTT&SUBMSN&MSN&MULTRA&KIESIG,,,,,,;
CHANGE-COSSU:COS,13,,,TA&TNOTCR&DSM&BASIC&TTT&SUBMSN&MSN&MULTRA,,,,,;
CHANGE-COSSU:COS,13,,,KIESIG&UUS1IM&UUS3&ACTMAN,,,,,;
 
just a question

is what I have to assign this COS for the Trunk or the trunk and the subscriber

yet is what directory you can give me the config COT.


Thanks
 
I also add that we have a single Trunk with this HIPATH.
 
Hi
No the COS's above are for phones.
Then change the phone to the COS setup like
CHA-SBCSU:STNO=XXXX,COS1=13,COS2=1;

The COS for a trunk would have to have 'TTT' in it for to transfer
 
after having performed all that, the problem still persists.

you can check with me, because I doubt a config system or the COP have left.

thank you



+---------------------------------------------+-------+-------+-------+-------+
| | | | | |
| UNIT | CON- | USED | FREE |BLOCKED|
| | TRACT | | | |
+---------------------------------------------+-------+-------+-------+-------+
| COMSCENDO | 235 | 233 | 2 | |
| CORDLESS E | 0 | 0 | 0 | |
| PNE | 0 | 0 | 0 | |
| SIGNALING SURVIVABILITY | 0 | 0 | 0 | |
| CC-AP FOR AP EMERGENCY | 0 | 0 | 0 | |
+---------------------------------------------+-------+-------+-------+-------+
H07: TRIAL MODE IS AVAILABLE 1 (MORE) TIME.

AMO-CODEW-111 CODEWORD FOR ADMINISTRATION LOCK IN SWU
DISPLAY COMPLETED;



DIS-DIMSU:ALL,;
H500: AMO DIMSU STARTED
+------------------------------------------------------------+
| MAX- SYS- |
| USED USED ACTUAL | STD MAX |
| CCIDXS : 894 894 2000 | 2000 4094 |
| CCIDXD : 2111 2111 3000 | 3000 4094 |
| GPIDX : 1345 1345 2000 | 2000 4000 |
| LINES : 1742 1742 32000 | 32000 32000 |
| PORTS : 1684 1720 16000 | 16000 16000 |
+------------------------------------------------------------+
| STATIONS: |
| STN : 205 205 12000 | 12000 20000 |
| |
| TERMINALS: |
| BUS : 22 22 12632 | 12632 16000 |
| OPTCC : 20 20 12000 | 12000 14000 |
| OPTEXP : 0 0 6000 | 6000 32000 |
| ATND : 1 1 32 | 32 256 |
| ES : 0 0 300 | 300 7000 |
| ESSTN : 0 0 1800 | 1800 14000 |
| S2PP : 0 0 2 | 2 30 |
| AUXDIGI : 0 0 0 | 0 8000 |
| |
| TRUNK AND TIE-LINE CIRCUITS: |
| PRI : 2 2 40 | 40 400 |
| TRK : 5 5 2400 | 2400 7920 |
| CRCP : 3 3 600 | 600 4000 |
| |
| DIAL PLAN: |
| DPLNCD : 99 99 2800 | 2800 32000 |
| DPLNGR : 0 0 350 | 350 32000 |
| |
| DEVICE SEARCH: |
| RTE : 5 260 1450 | 1450 64000 |
| MG : 5 5 850 | 850 64000 |
| SG : 4 4 818 | 818 2000 |
| ATNDGR : 0 0 10 | 10 16 |
| HT : 0 0 600 | 600 999 |
| HTCQB : 0 0 3000 | 3000 5000 |
| |
| CALL PROCESSING: |
| CPB : 0 6 6000 | 6000 10000 |
| SILI : 0 10 13500 | 13500 16000 |
| COSTI : 0 0 5688 | 5688 5688 |
| |
| DERIVED PARAMETERS: |
| LODEN : 347 407 55054 | 55054 57340 |
| SU : 21 21 12042 | 12042 14272 |
| NWBCHL : 33 63 1200 | 1200 12000 |
| LODS0 : 0 0 1920 | 1920 8000 |
| LODTMD : 0 2 1800 | 1800 8000 |
| CPDBUF : 0 33 6000 | 6000 10000 |
| DTILTG : 206 206 16000 | 16000 32000 |
| DTITMD : 0 5 2700 | 2700 12000 |
| NWNUNSUB: 254 254 256 | 256 32000 |
| |
| SUBSCRIBER FEATURES: |
| NAME : 24 24 12000 | 12000 20000 |
| EXTNAME : 0 1 2400 | 2400 32000 |
| ORG : 1 1 6000 | 6000 10000 |
| COS : 8 160 600 | 600 1000 |
| SPDI : 0 0 8400 | 8400 20000 |
| SPDCL : 0 0 16 | 16 16 |
| SPDCD : 0 0 3000 | 3000 16000 |
| CBK : 0 1 2400 | 2400 10000 |
| REMIND : 0 1 12000 | 12000 20000 |
| PUGR : 0 0 500 | 500 2000 |
| ID : 0 0 12000 | 12000 40000 |
| PINBUF : 0 0 1200 | 1200 20000 |
| CFWDEST : 1 5 12000 | 12000 64000 |
| CFWHIST : 0 2 12000 | 12000 32000 |
| HGMEMB : 0 0 1200 | 1200 20000 |
| CUGPROF : 0 0 20 | 20 200 |
| LIN : 0 0 3200 | 3200 32000 |
| ALTROUT : 0 0 2000 | 2000 20000 |
| LCRCOS : 6 7 50 | 50 1000 |
| HOTDEST : 0 0 500 | 500 20000 |
| |
| DIGITE FEATURES: |
| DSS : 0 0 18000 | 18000 28000 |
| DSSNA : 47 47 24000 | 24000 32000 |
| KEYSYS : 0 0 3600 | 3600 14000 |
| CALLOG : 0 0 2400 | 2400 12000 |
| COMGR : 0 0 400 | 400 1000 |
| SLKTEXT : 0 0 2000 | 2000 32000 |
| CALLOGS : 0 0 240 | 240 12000 |
| |
| ATTENDANT CONSOLE FEATURES: |
| ATNDCQ : 0 0 63 | 63 512 |
| NSTN : 1 2 30 | 30 256 |
| |
| TRUNK FEATURES: |
| MFCVAR : 0 0 3 | 3 10 |
| DSPMOD : 0 0 400 | 400 32000 |
| DPDSPMOD: 0 0 400 | 400 32000 |
| LODR : 5 100 1200 | 1200 4096 |
| LROUT : 4 4 1024 | 1024 64000 |
| LRTPROF : 0 0 200 | 200 10000 |
| LCRDSR : 0 0 1000 | 1000 10000 |
| SYNAN : 0 0 500 | 500 3200 |
| FORMTAB : 0 0 1000 | 1000 10000 |
| VOICO : 0 0 60 | 60 900 |
| |
| NETWORK FEATURES: |
| BLK100 : 44 44 400 | 400 8000 |
| RSTCON : 0 0 50 | 50 10000 |
| TEAMCONN: 0 0 180 | 180 1400 |
| DSS1SCRD: 0 0 0 | 0 10000 |
| DSS1SCRP: 0 0 0 | 0 10000 |
| REMPUGR : 0 0 1500 | 1500 10000 |
| PARTNODE: 0 0 600 | 600 4000 |
| LDPLN1 : 2 2 1200 | 1200 64000 |
| LDPLN2 : 0 0 0 | 0 64000 |
| LDPLN3 : 0 0 0 | 0 64000 |
| LDPLN4 : 0 0 0 | 0 64000 |
| LDPLN5 : 0 0 0 | 0 64000 |
| LDPLN6 : 0 0 0 | 0 64000 |
| LDPLN7 : 0 0 0 | 0 64000 |
| LDPLN8 : 0 0 0 | 0 64000 |
| LDPLNC1 : 0 0 120 | 120 6400 |
| LDPLNC2 : 0 0 0 | 0 6400 |
| LDPLNC3 : 0 0 0 | 0 6400 |
| LDPLNC4 : 0 0 0 | 0 6400 |
| LDPLNC5 : 0 0 0 | 0 6400 |
| LDPLNC6 : 0 0 0 | 0 6400 |
| LDPLNC7 : 0 0 0 | 0 6400 |
| LDPLNC8 : 0 0 0 | 0 6400 |
| |
| DATA FEATURES: |
| APPL : 0 0 98 | 98 98 |
| ECCS : 0 0 5 | 5 50 |
| DCIPAR : 0 0 1 | 1 255 |
| WSPROT : 20 20 12000 | 12000 14000 |
| INFO : 8 8 3000 | 3000 10000 |
| |
| ACD FEATURES: |
| ACDAGT : 0 0 256 | 256 8000 |
| ACDGRP : 0 0 128 | 128 255 |
| ACDLOGON: 0 0 256 | 256 1250 |
| ACDPRIM : 0 0 128 | 128 2000 |
| ACDCQ : 0 0 1500 | 1500 7500 |
| ACDRCG : 0 0 512 | 512 1020 |
| ACDRT : 0 0 300 | 300 4000 |
| ACDRTX : 0 0 900 | 900 16000 |
| ACDSHIFT: 0 0 300 | 300 20000 |
| ACDMONID: 0 0 256 | 256 5000 |
| ACDCALEN: 0 0 3200 | 3200 32000 |
| GDTR : 0 0 2000 | 2000 16000 |
| DNI : 0 0 2000 | 2000 16000 |
| DPDNI : 0 0 2000 | 2000 32000 |
| GENBUF : 0 0 256 | 256 5000 |
| |
| CAPACITY STAGE CONFIGURATION: |
| PERMDL : 215 215 1980 | 1980 1980 |
| CRICC : 0 0 1600 | 1600 8000 |
| WAML1 : 0 0 1 | 1 32 |
| WAML2 : 0 0 15 | 15 240 |
| STMA : 0 0 15 | 15 240 |
| STMACIR : 0 0 480 | 480 7680 |
| SLC24 : 0 0 8 | 8 150 |
| AP : 0 0 83 | 83 83 |
| GWREG : 0 0 1024 | 1024 9999 |
| SCTPATH : 0 0 2500 | 2500 64000 |
| CCAP : 0 0 0 | 0 83 |
| APEGRP : 0 0 0 | 0 83 |
| CGW : 1 1 143 | 143 150 |
| |
+------------------------------------------------------------+

AMO-DIMSU-111 DIMENSIONING OF FEATURES, SWITCHING UNIT
DISPLAY COMPLETED;






DIS-ZAND:ALLDATA;
H500: AMO ZAND STARTED
GENERAL SYSTEM DATA:
====================
TRANSFER = EXTEND , ALERTN = YES ,
AUTHUP = TA ,
RNGBKTN = YES , TRANSINH = NO ,
NIGHT = TA ,
ITRFWD = YES , HOLDTN = MUSIC , ANATESIG = TONE ,
DSSLT = 70, CODTN = YES , CONFSUB = NO ,
DATEDIS = DDMM, CNTRYCD = 0 , RCLLT = NO ,
MELODY = 1, TRCD = , CPBLOWL = 80 ,
CPBUPPL = 100, CUTHRU1A = YES , PREDIA = YES ,
SIUANN = 2, CO = NO , COEXN = 0 ,
CBKNO = 5 , SEVDIG = NO , PNNO = 200,
DISPMODE = MODE1, PNODECD = **85 , ROUTOPTP = NO ,
ROUTOPTD = NO , CALLOFF = YES , PARARING = NO ,
DSSDEST = YES , ONEPARTY = YES , MSGDELAY = NO ,
EXCOCO = YES , TRDGTPR = NO , COANN = YES ,
HOTDIAL = NO , TRANSTOG = NO , NOCFW = NO ,
HOLDHUNT = NO , POSTDDLY = YES , EXBUSYOV = NO ,
OVRMST = NO , OVRHUNT = NO , CONITPRO = YES ,
RECHUNT = NO , CALLACMP = NO ;

AMO-ZAND -111 SYSTEM DATA
DISPLAY COMPLETED;






DIS-TDCSU:1-1-115-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-01-115-0 TGRP = 100 |
|---------------------------------------------------------------------------|
| PROTVAR = ETSI INS = Y SRCHMODE = CIR |
| COTNO = 10 COPNO = 100 DPLN = 0 |
| ITR = 0 COS = 13 LCOSV = 1 |
| LCOSD = 1 CCT = 2 MBIT MERA DESTNO = 30 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 120 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 10 FWDX = 1 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729AOPT SRCGRP = |
| TCCID = SECLEVEL = TRADITIO |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 9 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| DMCALLWD = VNNO = |
| SVCDOM = |
| BCHAN = 1 && 15 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 15

AMO-TDCSU-111 DIGITAL TRUNKS
DISPLAY COMPLETED;







DIS-SCSU:7854;
H500: AMO SCSU STARTED

------------------------------- USER DATA -----------------------------------
STNO =5500 COS1 =13 DPLN =0 SPDI =0
PEN = 1- 1- 25- 0 COS2 =3 ITR =0 SPDC1 =
DVCFIG =ANATE LCOSV1 =1 COSX =0 SPDC2 =
INS =YES LCOSV2 =1 RCBKB =NO
PMIDX =0 ALARMNO =0 LCOSD1 =1 HMUSIC =0 RCBKNA =NO
SSTNO =NO COTRACE =NO LCOSD2 =1 SPEC =
COFIDX =0 DIAL =DTMF PULSTYPE= PULSLEV=
CCTIDX = ACKST = TEXTSEL=(GERMAN )
DHPAR = NEONMWI=
CONN =DIR FLASH =YES DTMFBLK =NO WITKEY :NO
------------------- ACTIVATION IDENTIFIERS FOR FEATURES ---------------------
DND :NO CWT :NO
HTOS :NO HTOF :NO HTOD :NO VCP :NO
--------------------- FEATURES AND GROUP MEMBERSHIPS ------------------------
PUGR : HUNTING GROUP : NO
NIGHT OPTION : NO
------------------------- STATION ATTRIBUTES (AMO SDAT) ---------------------
NONE
-----------------------------------------------------------------------------

AMO-SCSU -111 STATION CONFIGURATION OF SWITCHING UNIT
DISPLAY COMPLETED;






DIS-COT:10;
H500: AMO COT STARTED

COT: 10 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
TRUNK CALL TRANSFER XFER
TRUNK SIGNALING ANSWER ANS
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN
NETWORKWIDE CALL FORWARDING PERMITTED FWDN
NETWORKWIDE FORWARDING NO-ANSWER FNAN
CALL FORWARDING VIA PUBLIC NETWORK REROUTING FWDR
PREVENT CALL FORWARDING OF FORWARDED CALLS TO CO AICF
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY) TSCS
CALL FORWARDING PROGRAMING FOR OTHER SUBSCRIBERS CFOS
CALL FORWARDING VALIDATION PROCEDURES POSSIBLE CFVA
ACTIVATE, DEACTIVATE, INTERROGATE CALL FORWARDING FOR TRUNKS CFTR
DISPLAY DAILED NUMBER OF SUBSCRIBER B AT SUBSCRIBER A DISN
NETWORK CALL TRANSFER, EXPLICIT CALL TRANSFER NCT
NO TONE NTON

AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING
DISPLAY COMPLETED;




DIS-COSSU:COS,13;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 13 |>STD COS WITH EXTNL FWDING ALLOWED |
| | TA | TA | TA |
| | TNOTCR | TNOTCR | TNOTCR |
| | CDRS | BASIC | DSM |
| | CDRC | TTT | BASIC |
| | CDRIND | SUBMSN | TTT |
| | CDRINT | MSN | SUBMSN |
| | COSXCD | MULTRA | MSN |
| | MB | KIESIG | MULTRA |
| | DATA | | KIESIG |
| | CFNR | | UUS1IM |
| | VCE | | UUS3 |
| | FWDNWK | | ACTMAN |
| | TTT | | |
| | CFB | | |
| | FWDFAS | | |
| | FWDDIR | | |
| | CFSWF | | |
| | CW | | |
| | UUS3 | | |
| | ACTMAN | | |
+------+-----------------+---------------+-----------------+

AMO-COSSU-111 CLASSES OF SERVICE
DISPLAY COMPLETED;






REG-COP:;
H500: AMO COP STARTED
ADD-COP:8,DTMF&SFRM&RLSA&BR64&TDED&NO1A&DITW&TIM1&NSDL&IDP2&DTM1,,
;
CHANGE-COP:8,COPADD,,,,INDEP,
"TMANI-DTMF";
ADD-COP:100,,TA,TA;
ADD-COP:101,EOD&SFRM&CCR&L3AR,TA,TA;
ADD-COP:160,EOD&SFRM&CCR&L3AR,,;

AMO-COP -111 CLASS OF PARAMETER FOR DEVICE HANDLER
REGENERATE COMPLETED;






 
Can you please
DIS-ZAND:DIST;

This allows or limits the maximum diversions possible for a call to 'hop along'
 
I am just re-reading you original posting.
You say that you have only one trunk ?

Incoming call -> Answered -> Consultation -> dial external number -> Transfer = Transfer fails ??

Are you looking to transfer calls AND/OR divert calls ?

(Transferring also needs correct node numbering)

 
Please change as follows and retest:

CHA-TDCSU:pEN=1-1-115-0,FWDX=5;
 
You should also enable TRANSTOG=YES in ZAND ALLDATA
CHA-ZAND:TYPE=ALLDATA,TRANSTOG=YES;

This allows you to transfer a call as follows:

Incoming call -> Answered > Consultation > dial extension/external number> Hangup will transfer automatically.

If TRANSTOG=NO then hangup will just hangup.


 
To give the MAXIMUM allowed forwardings/diversions for different equipments:
(This is not set to full allowed on default)
(Not on early versions of HiPath)

CHANGE-ZAND:DIST,1,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,1,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,1,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,1,CD,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,2,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,2,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,2,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,2,CD,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,3,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,3,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,3,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,3,CD,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,4,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,4,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,4,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,4,CD,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,5,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,5,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,5,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,5,CD,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,6,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,6,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,6,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,6,CD,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,7,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,7,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,7,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,7,CD,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,8,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,8,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,8,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,8,CD,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,9,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,9,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,9,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,9,CD,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,10,CFU,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,10,CFB,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,10,CFNR,10,CFU&CFB&CFNR&CD;
CHANGE-ZAND:DIST,10,CD,10,CFU&CFB&CFNR&CD;

 
First of all, thank you for support.

I tried everything you asked me to do, but the problem remains.

I changed the FWDX.

as I typed every line of "CHANGE-ZAND: DIST."


I explain the case


Incoming call -> Answered -> Consultation -> dial external number -> Transfer = Transfer OK ?? and not Transfer fails

Incoming call -> "STNO FORWARDED" -> dial external number -> dial fail. that's my problem simply
 
I still better explained

Incoming call -> Answered -> Consultation -> dial external number -> Transfer = Transfer OK ?? and not Transfer fails

Incoming internal call -> "STNO FORWARDED to external number" -> dial external number -> dial OK.

Incoming external call -> "STNO FORWARDED to external number" -> dial external number -> dial fails, no dial tone, just the empty. that's my problem simply
 
Hi
Well I hope you copied and paste the ZAND DIST and not type in each one !?

Anyhow it looks like your node numbering so could be wrong.
If the NODE Numbering is incorrect when you go to transfer a call to an external number it will try and transfer to itself and will then fail.

You have to specify the NODE in LDAT with the same NODE in RICHT

I think if we get the transfer working then the forwarding should also work.


Here is an example of a working system with node numbers:

Add a NODE in KNDEF
with CHANGE-KNDEF:666,,,,,,,,,,,,,,,,,0,,;

In RICHT LRTE make the DNNO=666
In the corresponding LDAT's make the 'DNNO OF ROUTE=666' (this may be the problem)
In the TDCSU make the NNO=666 and the DESTNO=254 or something other than 666

What NODE numbers do you have already setup on all of these ?
 
ADD-RICHT:LRTENEW,260,ALL,"IPCISCO ",
100,0,,,
,,"",,,,30,,NO,
NO,"NO",0,
NEUTRAL,NO,NO,NO,NO,NO,NO,NO,NO ;



DIS-RICHT:LRTE,260,;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 260 NAME = IPCISCO (NEUTRAL) LSVC = ALL |
| DNNO = 0 PDNNO = 0 DESTNO = 30 |
| ROUTOPT = NO REROUT = YES PLB = YES FWDBL = NO |
| DTMFCNV = WITHOUT DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = BUGS = LIN ROUTATT = NO MAINGRP = 5 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 5 |
| INFO = NO |
| NOPRCFWD = NO |
| NITO = NO |
| CLNAMEDL = NO |
| FWDSWTCH = NO |
| LINFEMER = NO |
| NOINTRTE = NO |
+-----------------------------------------------------------------+
| TGRP = 100 LDAT 2 MBIT MERA (NEUTRAL) SUBGROUP = 1 |
+-----------------------------------------------------------------+

AMO-RICHT-111 TRUNK ROUTING
DISPLAY COMPLETED;




ADD-LDAT:260,ALL,1,,100,8,1
,
,1,EMPTY,
NONE,
,4,,,,
,,,
,,,,,;


DIS-LDAT:ALL,260;
H500: AMO LDAT STARTED
+------------------------------------------------------------------------------+
| LROUTE = 260 LDPLN NAME = IPCISCO SERVICE = ALL |
| TYPE = LCR DNNO OF ROUTE = 0 |
| SERVICE INFO = NO |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
| | | | | | SCHEDULE | CARRIER | | | |
|LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH | ZONE| LATTR | LDSRT|COTIDX |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
| 1| 1| 100| 8| 1 | ******** | 1 EMPTY| NONE | | 0 |
+------------------------------------------------------------------------------+

AMO-LDAT -111 LCR-DIRECTIONS
DISPLAY COMPLETED;



so DNNO = 0

 
REG-KNDEF;

ADD-KNDEF:NNO=666,TYPE=OWN,ISDNCC=XXX,ISDNAC=XX,ISDNLC=XXX,ISDNSK=3,ISDNUL=EXT,PNPUL=EXT;
CHANGE-KNDEF:NNO=666,DFLT=Y;


CHANGE-RICHT:MODE=LRTE,LRTE=666,DNNO=666,DTMFPULS=PP80;

CHANGE-LDAT:LROUTE=1,LRTEL=1,DNNO=666;
 
Sorry it should be:

CHANGE-RICHT:MODE=LRTE,LRTE=260,DNNO=666,DTMFPULS=PP80;
 
hello

it still not working

I found two site which had the same problem




on one, I found it:


You will have to get the node numbering correct, in the TDCSU, ZAND and RICHT and LDAT.
If the node numbering is not correct it will be looking up its own *~%$ and wont allow you to transfer trunk to trunk.


Post a Regen of the system or just
TDCSU
RICHT
LDAT
KNMAT
KNFOR
KNDEF
ZAND alldata


I would like to understand the amo KNMAT, KNFOR, KNDEF,

before starting the regeneration, let me give you the result of the last config:

<ADD-KNDEF:NNO=666,TYPE=OWN,ISDNCC=XXX,ISDNAC=XX,ISDNLC=XXX,ISDNSK=3,ISDNUL=EX
T,PNPUL=EXT;
M33: VALUE TYPE DOES NOT CORRESPOND TO TYPE IN VALUE TABLE
ISDNCC = ?
ISDNCC : ISDN COUNTRY CODE
CHARACTERISTIC : OPTIONAL
POSSIBLE VALUES : MAX. OF 4 POSITIONS
ISDNCC = 1;
M33: VALUE TYPE DOES NOT CORRESPOND TO TYPE IN VALUE TABLE
ISDNAC = ?
ISDNAC : ISDN AREA CODE
CHARACTERISTIC : OPTIONAL
POSSIBLE VALUES : MAX. OF 10 POSITIONS
ISDNAC = 1;
M33: VALUE TYPE DOES NOT CORRESPOND TO TYPE IN VALUE TABLE
ISDNLC = ?
ISDNLC : ISDN LOCAL DESTINATION CODE
CHARACTERISTIC : OPTIONAL
POSSIBLE VALUES : MAX. OF 10 POSITIONS
ISDNLC = 1;
ADD-KNDEF:NNO=666,TYPE=OWN,ISDNCC=1,ISDNAC=1,ISDNLC=1,ISDNSK=3,ISDNUL=EXT,
PNPUL=EXT;
H500: AMO KNDEF STARTED
H06: PARAMETERS DPLN AND ADPLN HAVE NO EFFECT
AS THE VIRTUAL DIALING PLAN FEATURE IS NOT ACTIVE.
F10: ISDNSK 3 MUST BE NOT LONGER THAN THE LENGTH OF ISDNLC (1)
ISDNSK = ?
ISDNSK : ISDN SKIP DIGITS
CHARACTERISTIC : OPTIONAL
POSSIBLE VALUES : 0-10
ISDNSK = 1;
H06: PARAMETERS DPLN AND ADPLN HAVE NO EFFECT
AS THE VIRTUAL DIALING PLAN FEATURE IS NOT ACTIVE.
H01: NNO 666 ADDED

AMO-KNDEF-111 VIRTUAL NODES
ADD COMPLETED;







<reg-kndef
M40: APPLICABLE GROUP CONDITION: MAXIMUM OF 1 OUT OF 2 PARAMETERS
NNO = ;
REG-KNDEF:;
H500: AMO KNDEF STARTED
ADD-KNDEF: 100 ,OWN , , , , ,EXT ,
, , , ,EXT , , , , ,
;
CHANGE-KNDEF: 100 ,,,,,,,,,,,,,,Y;
ADD-KNDEF: 666 ,OWN ,1 ,1 ,1 ,1 ,EXT ,
, , , ,EXT , , , , ,
;

AMO-KNDEF-111 VIRTUAL NODES
REGENERATE COMPLETED;
<CHANGE-KNDEF:NNO=666,DFLT=Y;
CHANGE-KNDEF:NNO=666,DFLT=Y;
H500: AMO KNDEF STARTED
H06: PARAMETERS DPLN AND ADPLN HAVE NO EFFECT
AS THE VIRTUAL DIALING PLAN FEATURE IS NOT ACTIVE.
H02: NNO 666 CHANGED

AMO-KNDEF-111 VIRTUAL NODES
CHANGE COMPLETED;
<CHANGE-RICHT:MODE=LRTE,LRTE=260,DNNO=666,DTMFPULS=PP80;
CHANGE-RICHT:MODE=LRTE,LRTE=260,DNNO=666,DTMFPULS=PP80;
H500: AMO RICHT STARTED
F69: IF DTMFCONV = WITHOUT, DTMFPULS MUST NOT BE SPECIFIED

AMO-RICHT-111 TRUNK ROUTING
CHANGE NOT COMPLETED;


I tried to modify several parameters, so everything has been changed



DIS-TDCSU:1-01-115-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-01-115-0 TGRP = 100 |
|---------------------------------------------------------------------------|
| PROTVAR = ETSI INS = Y SRCHMODE = CIR |
| COTNO = 10 COPNO = 101 DPLN = 0 |
| ITR = 0 COS = 13 LCOSV = 1 |
| LCOSD = 1 CCT = 2 MBIT MERA DESTNO = 30 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 210 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 10 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729AOPT SRCGRP = |
| TCCID = SECLEVEL = TRADITIO |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 9 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| DMCALLWD = VNNO = |
| SVCDOM = |
| BCHAN = 1 && 15 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 15

AMO-TDCSU-111 DIGITAL TRUNKS
DISPLAY COMPLETED;
<dis-richt
MODE = lrte
LRTE = 260;
DIS-RICHT:LRTE,260;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 260 NAME = IPCISCO (NEUTRAL) LSVC = ALL |
| DNNO = 200 PDNNO = 0 DESTNO = 30 |
| ROUTOPT = NO REROUT = YES PLB = YES FWDBL = NO |
| DTMFCNV = WITHOUT DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = BUGS = LIN ROUTATT = NO MAINGRP = 5 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 5 |
| INFO = NO |
| NOPRCFWD = NO |
| NITO = NO |
| CLNAMEDL = NO |
| FWDSWTCH = NO |
| LINFEMER = NO |
| NOINTRTE = NO |
+-----------------------------------------------------------------+
| TGRP = 100 LDAT 2 MBIT MERA (NEUTRAL) SUBGROUP = 1 |
+-----------------------------------------------------------------+

AMO-RICHT-111 TRUNK ROUTING
DISPLAY COMPLETED;
<dis-ldat
TYPE = ?
TYPE : DISPLAY TYPE
CHARACTERISTIC : OPTIONAL
POSS. VALUES : LCR ONLY LROUTES FOR LCR
NWLCR ONLY LROUTES WITH CLOSED NUMBERING BY LCR
ALL ALL
TYPE = all
LROUTE = 260;
DIS-LDAT:ALL,260;
H500: AMO LDAT STARTED
+------------------------------------------------------------------------------+
| LROUTE = 260 LDPLN NAME = IPCISCO SERVICE = ALL |
| TYPE = LCR DNNO OF ROUTE = 200 |
| SERVICE INFO = NO |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
| | | | | | SCHEDULE | CARRIER | | | |
|LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH | ZONE| LATTR | LDSRT|COTIDX |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
| 1| 1| 100| 8| 1 | ******** | 1 EMPTY| NONE | | 0 |
+------------------------------------------------------------------------------+

AMO-LDAT -111 LCR-DIRECTIONS
DISPLAY COMPLETED;
<dis-knmat
NPI = ;
DIS-KNMAT:;
H500: AMO KNMAT STARTED
H01: NO ENTRY WITH THE REQUIRED ATTRIBUTES AVAILABLE

AMO-KNMAT-111 NODE DATA FOR NETWORKING
DISPLAY COMPLETED;
<dis-knfor
DNNO = ;
DIS-KNFOR:;
H500: AMO KNFOR STARTED
H02: DNNO NOT FOUND IN NPI ISDN.
H02: DNNO NOT FOUND IN NPI PRIVATE.

AMO-KNFOR-111 ADMINISTER OF NODE FORMAT TABLES
DISPLAY COMPLETED;
<dis-kndef
M40: APPLICABLE GROUP CONDITION: MAXIMUM OF 1 OUT OF 2 PARAMETERS
NNO = ;
DIS-KNDEF:;
H500: AMO KNDEF STARTED
VIRTUAL NODE TABLE
+-----------+-------+--------------+--------------+-----------+-----+-----+----+
| VIRTUAL | TYPE | ISDN (E.164) | PRIVATE(PNP) | UNKNOWN |POPU-| CAC |DFLT|
| NODE | | CC | L2 | | LA- | PRE-| |
| NUMBER | | AC | L1 | |TION | FIX | |
| | | LC SK | L0 SK | NODECD SK | | | |
| | | UL | UL | | | | |
+===========+=======+==============+==============+===========+=====+=====+====+
| 100 |OWN | | | | 201| | |
| | | | | | | | |
| | | | | | | | |
| | | EXT | EXT | | | | |
+ +=======+==============+==============+===========+=====+=====+====+
| | DPLN | ADPLN | |
+ +=======+==============+==============+===========+=====+=====+====+
+ | | |
+-----------+-------+--------------+--------------+-----------+-----+-----+----+
| 666 |OWN | 1 | | | 0| | Y |
| | | 1 | | | | | |
| | | 1 1 | | | | | |
| | | EXT | EXT | | | | |
+ +=======+==============+==============+===========+=====+=====+====+
| | DPLN | ADPLN | |
+ +=======+==============+==============+===========+=====+=====+====+
+ | | |
+-----------+-------+--------------+--------------+-----------+-----+-----+----+
| 444 |OWN | 212 | | | 0| | |
| | | 23 | | | | | |
| | | | | | | | |
| | | EXT | EXT | | | | |
+ +=======+==============+==============+===========+=====+=====+====+
| | DPLN | ADPLN | |
+ +=======+==============+==============+===========+=====+=====+====+
+ | | |
+-----------+-------+--------------+--------------+-----------+-----+-----+----+
| 1 |OWN | 212 | | | 0| | |
| | | 23 | | | | | |
| | | | | | | | |
| | | EXT | EXT | | | | |
+ +=======+==============+==============+===========+=====+=====+====+
| | DPLN | ADPLN | |
+ +=======+==============+==============+===========+=====+=====+====+
+ | | |
+-----------+-------+--------------+--------------+-----------+-----+-----+----+

AMO-KNDEF-111 VIRTUAL NODES
DISPLAY COMPLETED;
<dis-zand:alldata;
DIS-ZAND:ALLDATA;
H500: AMO ZAND STARTED
GENERAL SYSTEM DATA:
====================
TRANSFER = EXTEND , ALERTN = YES ,
AUTHUP = TA ,
RNGBKTN = YES , TRANSINH = NO ,
NIGHT = TA ,
ITRFWD = YES , HOLDTN = MUSIC , ANATESIG = TONE ,
DSSLT = 15, CODTN = YES , CONFSUB = NO ,
DATEDIS = DDMM, CNTRYCD = 0 , RCLLT = NO ,
MELODY = 1, TRCD = , CPBLOWL = 80 ,
CPBUPPL = 100, CUTHRU1A = NO , PREDIA = NO ,
SIUANN = 3, CO = YES , COEXN = 0 ,
CBKNO = 5 , SEVDIG = NO , PNNO = 101,
DISPMODE = MODE1, PNODECD = 102 , ROUTOPTP = NO ,
ROUTOPTD = NO , CALLOFF = YES , PARARING = YES ,
DSSDEST = YES , ONEPARTY = YES , MSGDELAY = NO ,
EXCOCO = YES , TRDGTPR = YES , COANN = YES ,
HOTDIAL = YES , TRANSTOG = YES , NOCFW = NO ,
HOLDHUNT = NO , POSTDDLY = NO , EXBUSYOV = NO ,
OVRMST = NO , OVRHUNT = NO , CONITPRO = YES ,
RECHUNT = NO , CALLACMP = NO ;

AMO-ZAND -111 SYSTEM DATA
DISPLAY COMPLETED;
<
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top