problem link E1 hip4000 to CO thought Huawei system 1

[Karmozdi]

hello dear Sbcsu
I have problem about E1 trunk Hip4000 with CO Communication thought Huawei system
Hip 4000 is ETSI-S2COD slave and SMD and CRC4 are N
in Communication on Huawei system is Master and CRC4 N
I change variants Protvar and DEV and change LWPAR but I didn't have any signaling.
Please help me how can I configuration trunk rout?
best regards
..................
ADD-TDCSU:NEW,1-05-014-1,0,0,0,0,70,32,1,"ISDN ",10,ETSI,1,,NONE,,,,GDTR,N,CO,NONE,N,0,,00,0,,,2995,10,MANY,10,2,1,1,EMPTY,0,5,N,,,,,,16,8,1,10,,EC&G711&G729AOPT,,22,CIR,N,TRADITIO,0,60,60,S2COD,1&&30,N,1,3,0,0,0,0,0;

CHANGE-LWPARIUS2,3,COPPER,S2,ON,N,16,0,D5,10,10,N,Y,DF,N,0,255,N,N,INDEP,;
RESTART-BSSUEN,1,5,14,;
DEACT-DSSUI,PEN,1-5-14-1;
ACTIVATE-DSSU:AUL,BCHAN,1-5-14-1;
MULTLINE 30 . . . . . . . . . . . . . .UNACH
000 NO CONN
001 NETWORK SUBUNIT . TMD CO ISDN UNACH/CP
(ALT_ROUT: N) (S2COD )
LINE: 2879 STNO: SI:
001 . . . . . . . . TMD CO ISDN UNACH/CP
002 NETWORK SUBUNIT . TMD CO ISDN UNACH/CP
(ALT_ROUT: N) (S2COD )

 

[Karmozdi]

No the trunk not vorking
DIS-SDSU:ALL,,PEN,PER3,1,5,14,1;
H500: AMO SDSU STARTED

LTG1 (PERIPHERY)
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
------------------- LTG 1 --------------------- READY
-AP370013-----SG 1 LTU 5 --------------------- READY
** .LTG 1.LTU 5.014 DIU-N2 Q2196-X READY
CCT LINE STNO SI BUS TYPE
001 2879 PP NW READY
MULTLINE 30 . . . . . . . . . . . . . .READY
000 NO CONN
001 NETWORK SUBUNIT . TMD CO ISDN GENNR/CP
(ALT_ROUT: N) (S2COD )
LINE: 2879 STNO: SI:
001 . . . . . . . . TMD CO ISDN GENNR
002 NETWORK SUBUNIT . TMD CO ISDN GENNR/CP
(ALT_ROUT: N) (S2COD )

 

[masviss]

So the next step is
DEA-DSSUI,PEN,1-5-14-1;

 

[Karmozdi]

Oh dear masviss thank you very match in advance
I con not understand what different between my tdcsu and your tdcsu trunk .whate do you do?
now channels are ok
lets me check rout

DIS-SDSU:ALL,,PEN,PER3,1,5,14,1;
H500: AMO SDSU STARTED

LTG1 (PERIPHERY)
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
------------------- LTG 1 --------------------- READY
-AP370013-----SG 1 LTU 5 --------------------- READY
** .LTG 1.LTU 5.014 DIU-N2 Q2196-X READY
CCT LINE STNO SI BUS TYPE
001 2879 PP NW READY
MULTLINE 30 . . . . . . . . . . . . . .READY
000 NO CONN
001 NETWORK SUBUNIT . TMD CONN ISDN READY
(ALT_ROUT: N) (S2CONN )
LINE: 2879 STNO: SI:
001 . . . . . . . . TMD CONN ISDN READY
002 NETWORK SUBUNIT . TMD CONN ISDN READY

 

[masviss]

Moriendi told you about this, it was necessary to change
the devtype instead of s2cod, there should be s2conn in
addition to what we have already done.

 

[Karmozdi]

Because PRI connection is with communication,
I think if devtype be S2CONN, we can't communicate. I'll check it.
. I put a tie accepted
---------------------
ADD-TDCSU:NEW,1-05-014-1,100,100,0,0,100,1,1,"CO PRI ",0,"ECMAV2",8,,NONE,,,,GDTR,N,TIE,NONE,N,0,,00,0,,,,31,MANY,1-1-110,0,1,1,EMPTY,10,5,N,,,,,,16,8,0,10,,EC&G711&G729A,,100,CIR,Y,TRADITIO,0,60,60,S2CONN,1&&30,N,1,3,0,0,0,0,0,;

 

[Karmozdi]

unfortunately I could not send digits
--------------------
ADD-RICHT:LRTENEW,100,ALL,"TO PRI ",100,1-1-100,,,FIX,DIGITS,"PRI LINKS IN ",PP300,,,,,NO,NO,"PRI ROUTE",1-1-0,NEUTRAL,NO,NO,NO,NO,NO,NO,NO,NO;
----------
ADD-LODR:2,,,,ECHO,2;
ADD-LODR:2,,,,END;
----------
ADD-LDAT:100,ALL,1,,100,2,1,,1,EMPTY,NONE,,4,,,,,,,,,,,,;
-----------------------
ADD-WABE:833,,,TIE,N,,,,,,,,;
----------
ADD-LDPLN:LCRPATT,0,"833"-"X",0,100,,,1,,,,N;
-----------------------
CHANGE-COSSU:LCOSV,50,1&&64,,,,,;

I want to send 115 No to CO

 

[masviss]

If you want to dial 3 digits of the subscriber's number,
then the number of X in the LDPLN should be 3.

DEL-LDPLN:LCRPATT,0,833-X;

ADD-LDPLN:LCRPATT,0,833-XXX,0,100,,,1,,,,N;