problem dialing out

[Mack674]

problem dialing certain numbers over a pri.worked with carrier they said i need to remove the access control parameter from my d channel.does anyone know how to do this?

 

[GHTROUT]

Certain numbers" is what, to me, points to the problem.

What is common about those certain numbers?

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[Mack674]

the pri vendor is paetech they came in with a t bird and dialed this # 212-940-xxxx and the call went thru.i dial that same number i get an intercept recording from telco.the engineer monitored my call and stated that i must remove the access control parameter from d channel,because they are tandeming out to a mci\worldcom switch and mci\worldcom rejects it because it has the access control parameter

 

[GHTROUT]

So, one exchange has a problem? 212-940

-Set your own TN to TGAR 0 and CLS UNR
-Figure out the Trunk Route Access code for this PRI (ACOD prompt in the Route data)
-Dial the ACOD, hear dial tone, then 1212940-nnnn

If it goes through, it's your BARS programming. Report back your findings.

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[Mack674]

i already tried that and ive never heard of access control parameter

 

[GHTROUT]

You tried that, but you didn't say the result you got??

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[GHTROUT]

Nor did you confirm it was just that one Area code+exchange.

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[Mack674]

i got the same intercept when dialing trunk access code.it also happens on 212-451-nnnn.

 

[GHTROUT]

I guess posting the RDB and the DCH might generate some better answers. Also, setting the channels to 3VCE has been known to resolve a variety of problems. The default is VOD.

Quick way to spot your setting is LD60 .STAT

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[Mack674]

my channels are vce
REQ: prt
TYPE: rdb
CUST 0
ROUT 3

TYPE RDB
CUST 00
ROUT 3
DES PRI
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00001
NCNA NO
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
DSEL VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 7303
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510


PAGE 002

GRD 896
SFB 3
NBS 2048
NBL 4096
DRNG NO
CDR NO
MUS YES
MRT 7
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

REQ: ****
OVL000
>ld 22
PT2000

REQ prt
TYPE adan dch 34

ADAN DCH 34
CTYP TMDI
MG_CARD 004 0 01
PORT 1
DES DID
USR PRI
DCHL 34
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID 25
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
INC_T306 2
OUT_T306 30
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO
annels are vce

 

[Mack674]

I also changed my route to 3vce same thing.intercept from telco

 

[jamie2]

What digits do you see you are sending when monitoring the d-channel?