Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

PRI to PRI Calls Fail - Intercept to Operator 1

Status
Not open for further replies.

hskrdean

IS-IT--Management
Dec 4, 2008
80
US
I am working on connecting a faxing server to our CS1000 via a PRI T1 using NI2 d-channel. The T1 is up and connected and I can forward/send calls to the fax server through my incoming T1s, both local and LD (local DID and 800 #).

However, I cannot get any calls from the fax server to get out of the Nortel. Local/LD calls are intercepted and sent to the system operator. If the fax server dials a four digit extension, the call connects to the extension.

I have checked TARG/TGAR, NCOS/FRL and CLS. If a call goes one way through the system PRI to PRI, why won't it let it go through the other way?

_________________ FAX server DCH and RDB _____________________
REQ prt
TYPE adan dch 36

ADAN DCH 36
CTYP MSDL
MG_CARD 048 0 02
PORT 1
DES NOBLE_DIALER
USR PRI
DCHL 111
OTBF 127
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID 1
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO

REQ end
>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 18

TYPE RDB
CUST 00
ROUT 18
DES UNIFIER
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 7
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 8918
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 5 *
NDNO 5
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3


PAGE 002

NBS 2048
NBL 4096

IENB 5
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

______________________Outgoing RDB for LD calls _________________________________

REQ: prt
TYPE: rdb
CUST 0-
ROUT 16

TYPE RDB
CUST 00
ROUT 16
DES FRMGRP2
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D250
SBN NO
PNI 00001
NCNA YES
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS YES
NDGT 10
WDGT L
DDLY NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 8916
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DNAM NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 384
OGF 384
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640


PAGE 002

GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR YES
INC NO
LAST NO
QREC NO
OAL YES
AIA NO
OAN YES
OPD YES
CDRX NO
NATL YES
VRAT NO
MUS YES
MRT 30
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR YES
ASID 17
SFNB
USFB
CALB 7 8

REQ:
 
prt a tnb of the fax pri.. change the ncos so it's allowed ld.

john poole
bellsouth business
columbia,sc
 
John, here is the TNB and NCTL list. Notice the NCOS is 7, highest FRL in the system.


DES NOBLE
TN 111 01 VIRTUAL
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 7
RTMB 18 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 30 MAR 2010


NACT end
>ld 87
ESN000

MEM AVAIL: (U/P): 97732508 USED U P: 6033935 503378 TOT: 104269821
DISK SPACE NEEDED: 856 KBYTES
REQ prt
CUST 0
FEAT nctl
NRNG 0 7

SOHQ NO
SCBQ NO

NCOS 0

EQA NO
FRL 0
RWTA NO
NSC NO
OHQ NO
CBQ NO
SPRI 0
MPRI 0
PROM 0

NCOS 1

EQA NO
FRL 1
RWTA NO
NSC NO
OHQ NO
CBQ NO
SPRI 0
MPRI 0
PROM 0

NCOS 2

EQA NO
FRL 2
RWTA NO
NSC NO
OHQ NO
CBQ NO
SPRI 0
MPRI 0
PROM 0

NCOS 3

EQA NO
FRL 3
RWTA NO
NSC NO
OHQ NO
CBQ NO
SPRI 0
MPRI 0
PROM 0

NCOS 4

EQA NO
FRL 4
RWTA NO
NSC NO
OHQ NO
CBQ NO
SPRI 0
MPRI 0
PROM 0

NCOS 5

EQA NO
FRL 5
RWTA NO
NSC NO
OHQ NO
CBQ NO
SPRI 0
MPRI 0
PROM 0

NCOS 6

EQA NO
FRL 6
RWTA NO
NSC NO
OHQ NO
CBQ NO
SPRI 0
MPRI 0
PROM 0

NCOS 7

EQA NO
FRL 7
RWTA NO
NSC NO
OHQ NO
CBQ NO
SPRI 0
MPRI 0
PROM 0

TOHQ NONE

 
Villareal- LD 49 is for the IDC table. NCOS 0 has an FRL of 0 as shown above in the LD 87 NCTL print out.
 
if your using ac1 or ac2 you bypass ld 49.. if your not using ld 90, good luck

john poole
bellsouth business
columbia,sc
 
Ok, so let me try to talk this through. The Fax server gets dial tone on the trunk to the PBX, then sends 9 +1 and the number. So I am using BARS to route the call to the LD trunks. But after the digits are sent, the call is intercepted and goes to the receptionist. I can see that by running a d-channel monitor trace.

I tried sending the call out a COT route, a PRI using TIE trunks and then changing it to use DID trunks. In all cases, the fax server call was intercepted.

I've got to be doing SOMETHING wrong, but I can't see it. ARGH!!!!
 
Sounds like you're tandeming the call out, is this correct?

FaxServ - PRI - PBX - PRI - PSTN

If so, you need to insert a 9 into your outpulsed string from the fax server, that way you have access BARS on the PBX
 
Here's a copy of the d-channel trace from the fax server dch...

.
DCH 36 UIPE_IMSG CC_SETUP_IND REF 00000480 CH 111 8 TOD 11:33:26 CK 8B81EC56
CALLED #:918002280141 NUM PLAN: E164 TON: NATL

DCH 36 UIPE_OMSG CC_REJECT_REQ REF 00008480 CH 111 8 TOD 11:33:26 CK 8B81EC57
CAUSE: #1 - UNASSIGNED NUMBER

DCH 36 UIPE_IMSG CC_SETUP_IND REF 00000500 CH 111 8 TOD 11:33:26 CK 8B81F000
CALLED #:918775644440 NUM PLAN: E164 TON: NATL

DCH 36 UIPE_OMSG CC_REJECT_REQ REF 00008500 CH 111 8 TOD 11:33:26 CK 8B81F001
CAUSE: #1 - UNASSIGNED NUMBER
 
Tandem NI2 calls just don't work in Nortel. NI2 only allows for COT or DID type trunks. In order for the nortel to process your request, you'll have to build TIE trunks and NI2 doesn't support TIE.

Solution: Use QSIG TIEs or change to DTI E&M WNK TIE trunks.

Nortel doesn't function well as an NI2 traffic cop.

 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top