PRI to Bell Issue

[onei0067]

Has any one ever encountered this? We have 5 T1's to Bell Canada our LP's 10,11,33,76,77. Bell requires 1 DCH which we put on LP 10 (DCH 0)and the BDCH on LP 77 (DCH 23). The DCH establishes so we know our connection is good, however any channels seized on LP 11 or 76 ring at the far end but do not ring at our end and give dead air. We have The PRI Interface ID for DCH 0 (LP 10) setup to handle LP 11,33,76. The only difference in the programming is that on the LP's that work (10,33,77) there is an extra prompt in the PRINT that says STRI/STRO OWK OWK. We are being assured that everything is OK by our provider.

Signed onei0067, perplexed!

 

[bigindian65]

PRT in ld 11 post/look at TN 10 1 and 11 1, different? out members in ld 14 or non-working trunks, make them match trunk TN 10 1.

Mato' Was'aka

 

[onei0067]

Thanks for the reply...The only difference of course is the route and member, and the STRI/STRO. However when we build the channels in LD 14 there is no prompt for STRI/STRO. Here is the print...

DES MEGASYSTEM1
TN 010 01
TYPE ISA
CUST 0
TRK PRI
PDCA 1
PCML MU
RTMB 50 1
B-CHANNEL SIGNALING
TGAR 1
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR HKD
P10 VNL
TKID
DATE 4 FEB 2010

DES MEGASYSTEM5
TN 011 01
TYPE ISA
CUST 0
TRK PRI
PDCA 1
PCML MU
RTMB 50 95
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR HKD
P10 VNL
TKID
DATE 4 FEB 2010

These are new PRI cards that were working before the cutover.

 

[johnpoole]

PT0000
REQ: prt
TYPE: tnb
TN   77 1
DATE
PAGE
DES

DES  503567.3
TN   077 01
TYPE ISA
CUST 0
TRK  PRI
PDCA 1
PCML MU
RTMB 34 25
B-CHANNEL SIGNALING
TGAR 1
AST  NO
IAPG 0
CLS  UNR DTN CND ECD WTA HPR THFD SPCD
     P10 VNL
TKID
AACR NO
DATE 13 JAN 2009


NACT
REQ: prt
TYPE: tnb
TN   16 1
DATE
PAGE
DES

DES  DICTA
TN   016 01
TYPE TIE
CDEN SD
CUST 0
TRK  DTI
PDCA 1
PCML MU
NCOS 1
RTMB 16 1
TGAR 0
SIGL EAM
STRI/STRO WNK WNK
SUPN NO
AST  NO
IAPG 0
CLS  CTD DTN CND ECD WTA LPR APN THFD HKD SPCD
     P10 VNL
TKID
FCAR NO
AACR NO
DATE 25 JAN 2010

loop 77 is a working pri, note B-CHANNEL SIGNALING
loop 16 is a working t1, note STRI/STRO WNK WNK.. problem could be in a couple of places..1st place would be cequ.

  DLOP  NUM DCH FRM TMDI LCMT YALM TRSH
   TRK  016 24  ESF NO   B8S  FDL  00
   PRI  077 24  ESF NO   B8S  FDL  00

loop 16 was added as a trk, 77 as a pri.. the other palce would be your d..

  PRI  INTERFACE ID
  076  2
  077  3
  140  4

for that loop the d is on loop 125, it is the d for 125,76,77,140.. you have to disl the loop, out the trunks.. change what ever is missing and put the trunks back in.. ld 14 out 24 and new 24 makes that a 10 minute job..


john poole
bellsouth business
columbia,sc

 

[onei0067]

Thank you...We actually only have one route(50) The ADAN for DCH 0 is...

ADAN PRIM DCH 0
BDCH 23
CTYP MSDL
GRP 0
DNUM 15
PORT 0
DES MEGAPRIME
USR PRI
DCHL 10
OTBF 127
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100
SIDE USR
CNEG 1
RLS ID 37
RCAP ND2
PRI INTERFACE ID
011 2
033 3
076 4
T200 3
T203 10
N200 3
N201 260
K 7
and the CEQU is...

DLOP NUM DCH FRM LCMT YALM TRSH
PRI 010 24 ESF B8S FDL 00
011 24 ESF B8S FDL 00
025 24 ESF B8S FDL 00
032 24 ESF B8S FDL 00
033 24 ESF B8S FDL 00
076 24 ESF B8S FDL 00
077 24 ESF B8S FDL 00

LP 25 and 32 are testing LP's...

Just wondering if provider (Bell) has their layer 3 programming correct?