PRI SETUP 1

[ritelcarlos]

Hello,

Could you please help. I have a system that i am installing a PRI circuit and I cant get the outgoing part of the PRI working it works great for the inbound DIDS . the system has the following cards the system is a MAGIX 4.0 V 7.0 METAL CABINET AND THE EXPANSION CAB ALSO METAL. The following cards are installed slot 1 412 slot 2thru 5 016 etr cards
expansion cab 1st slot 016 t/r 2nd and third slot 800 iclid 4th slot merlin meassing 5th slot 412 slot 6 100DSI PART NUMBER 617N15 . i have two questions for now can the T1 card be installed in slot 11 and if so what is the first line number 825 correct? what happens is when an outgoing call is placed the user gets a second or two of silence and the a system reorder tone like a busy sound.

THANK YOU

 

[merlinman]

That would be correct, however the 617N15 sometimes has trouble with 016-TRR's to it's left.

You may need some help we can't give on this forum.

http://home.comcast.net/~merlinman

 

[ritelcarlos]

Well ok the first part of this question was to make sure i could install the T1 card in the last slot and yes i did know about the issues with the 016 tr card. so what i did is i backed the system up then i installed the T1 card in the second slot of the main cab did a board remunber and reprogramed the T1 settings all over again using the step by step set up i got here . I got the same results two second delay and a fast busy reorder .

thank you for your time please help

 

[TouchToneTommy]

Give an extension Pool Dial Out Code access to the pool of PRI channels. Dial your call with the pool code. This bypasses ARS and routing tables. See what happens. Post your ARS and PRI printouts here.

 

[ritelcarlos]

Well when i programed the pri circuits it put a line btn on the operators phone so i pressed the btn for line 825 and dial out but maybe this still does not pass restrictions because i got the same results. So i defaulted the entire system programed just what i needed 3 digit ext , hybrid, and of course PRI programing and got the same results on a almost defaulted proc.

this is all leading towards a bad proc ?

 

[TouchToneTommy]

You CAN'T dial directly on a PRI channel via a line button. You have to dial the call, and let the D channel communicate with the central office. That's why you need to dial 9 and let ARS do the work, or dial the pool code. Pressing # at the end signals the end of dialing and bypasses the "second or two of silence" at the end.

Now, didn't we address this here:

http://www.tek-tips.com/viewthread.cfm?qid=1614063&page=1

Help us help you. Print and post your PRI and ARS setups.

 

[SYQUEST]

ritelcarlos,

My sentiments as well! We asked you to post the requested info in that other thread, and you never did! We can't help you, if you don't cooperate with simple requests...

....JIM....

 

[ritelcarlos]

ok i will thank you

 

[kwing112000]

Have you doubled checked with the provider. I have seen this exact thing when they send Ni2. You could get calls in but never out.

Kevin Wing
ACSS Small and Medium Enterprise (SME) Communications
ACS- Implement IP Office
ACA- Implement IP Office
Carousel Industries

 

[ritelcarlos]

Ok thank you i opened a trouble ticket with the carrier for them to come out and use their test equip to make a call i get this feeling they will not be able to
i will let everyone here know on monday

thank you for your help

 

[ritelcarlos]

Kevin ,

The tech did not show up when i ordered the circuit i asked for CUSTOM so is it correct should it be NI 1 CUSTOM NOT NI2 ??

THANKS

 

[ritelcarlos]

A AUTOMATIC ROUTE SELECTION


A ARS IS: ACTIVE ACCESS CODE: 9


A TABLE 25: Default Toll Output Table

A Pool Absorb Other Digits FRL Call type Start Pattern
A 1)70-- 00 -------------------- 3 BOTH --:-- A
A 2)---- -- -------------------- - ----- --:-- A
A 3)---- -- -------------------- - ----- --:-- A
A 4)---- -- -------------------- - ----- --:-- A
A 5)---- -- -------------------- - ----- --:-- A
A 6)---- -- -------------------- - ----- --:-- A

A Pool Absorb Other Digits FRL Call type Start Pattern
A 1)70-- 00 -------------------- 3 BOTH --:-- B
A 2)---- -- -------------------- - ----- --:-- B
A 3)---- -- -------------------- - ----- --:-- B
A 4)---- -- -------------------- - ----- --:-- B
A 5)---- -- -------------------- - ----- --:-- B
A 6)---- -- -------------------- - ----- --:-- B
A AUTOMATIC ROUTE SELECTION



A TABLE 26: Default Local Output Table

A Pool Absorb Other Digits FRL Call type Start Pattern
A 1)70-- 00 -------------------- 2 BOTH --:-- A
A 2)---- -- -------------------- - ----- --:-- A
A 3)---- -- -------------------- - ----- --:-- A
A 4)---- -- -------------------- - ----- --:-- A
A 5)---- -- -------------------- - ----- --:-- A
A 6)---- -- -------------------- - ----- --:-- A

A Pool Absorb Other Digits FRL Call type Start Pattern
A 1)70-- 00 -------------------- 2 BOTH --:-- B
A 2)---- -- -------------------- - ----- --:-- B
A 3)---- -- -------------------- - ----- --:-- B
A 4)---- -- -------------------- - ----- --:-- B
A 5)---- -- -------------------- - ----- --:-- B
A 6)---- -- -------------------- - ----- --:-- B
A AUTOMATIC ROUTE SELECTION



A TABLE 27: Dial 0 Output Table

A Pool Absorb Other Digits FRL Call type Start Pattern
A 1)70-- 00 -------------------- 3 BOTH --:-- A
A AUTOMATIC ROUTE SELECTION



A TABLE 28: N11 Output Table
A 01)411 02)611 03)811

A Pool Absorb Other Digits FRL Call type Start Pattern
A 1)70-- 00 -------------------- 3 BOTH --:-- A
A AUTOMATIC ROUTE SELECTION



A TABLE 29: E911 Table (911)

A E911 Option: Partition

A Allow-11: Disable

A Other Digits for E911 calls redirected to Main Pool: --------------------

A E911 Adjunct Trunks:

A E911 Adjunct Alarm Extension:

A Partition 1:
A Extensions: 100 300 101 301 102 302 103 303
A 104 304 105 305 106 306 107 307 108 308
A 109 309 110 310 111 311 112 113 114 115
A 116 117 118 119 120 121 122 123 124 125
A 126 127 128 129 130 131 132 133 134 135
A 136 137 138 139 140 141 142 143 144 145
A 146 147 148 149 150 151 152 153 154 155
A 156 157 158 159
A Trunks:
A Other Digits: --------------------

A Partition 2:
A Extensions:
A Trunks:
A Other Digits: --------------------

A Partition 3:
A Extensions:
A Trunks:
A Other Digits: --------------------

A Partition 4:
A Extensions:
A Trunks:
A Other Digits: --------------------

A Partition 5:
A Extensions:
A Trunks:
A Other Digits: --------------------

A Partition 6:
A Extensions:
A Trunks:
A Other Digits: --------------------

A Partition 7:
A Extensions:
A Trunks:
A Other Digits: --------------------

A Partition 8:
A Extensions:
A Trunks:
A Other Digits: --------------------

A Partition 9:
A Extensions:
A Trunks:
A Other Digits: --------------------

A Partition 10:
A Extensions:
A Trunks:
A Other Digits: --------------------

P3F1FIM Tone N  $!ARS: ! ! ! N  $!Make a! selec!tion ! N  $!All ! ! ! N  $!Indivi!dual ! ! N  $! ! ! ! N  $! ! ! ! N  $!Back ! ! ! S V

 

[ritelcarlos]

A PRI INFORMATION



A Slot 3 Switch: 5ESS

A System: By line

A BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
A 1 3 CallbyCall By Dial Plan

A Channel ID: 23 22 21 20 19 18 17 16 15 14
A 13 12 11 10 9 8 7 6 5 4
A 3 2 1

A Line PhoneNumber NumberToSend
A 813
A 814
A 815
A 816
A 817
A 818
A 819
A 820
A 821
A 822
A 823
A 824
A 825
A 826
A 827
A 828
A 829
A 830
A 831
A 832
A 833
A 834
A 835

A Network Selection Table

A Entry Number: 0 1 2 3
A Pattern to Match: 101**** 10***

A Special Service Table

A Entry Number: 0 1 2 3 4 5 6 7
A Pattern to Match: 011 010 01 00 0 1
A Operator: none OP OP OP/P OP none none none
A Type of Number: I I I N N N N N
A Digits to Delete: 0 0 0 0 0 0 0 0

A Call-By-Call Service Table

A Entry Number: 0 1 2 3 4
A Pattern 0: 0
A Pattern 1: 1
A PRI INFORMATION


A Pattern 2: 2
A Pattern 3: 3
A Pattern 4: 4
A Pattern 5: 5
A Pattern 6: 6
A Pattern 7: 7
A Pattern 8: 8
A Pattern 9: 0
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ: No Service
A DeleteDigits: 0 0 0 0 0

A Entry Number: 5 6 7 8 9
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ:
A DeleteDigits: 0 0 0 0 0

A Dial Plan Routing Table

A Entry Number: 0 1 2 3
A NtwkServ: Any service
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:

A Entry Number: 4 5 6 7
A NtwkServ:
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:

A Entry Number: 8 9 10 11
A NtwkServ:
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:

A Entry Number: 12 13 14 15
A NtwkServ:
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:
P3F1FIM Tone N  $!Print !(Engli!sh )!: >N  $!Make a! selec!tion ! N  $!All ! !Trunk !Info N  $!SysSet!-up !T1 Inf!o N  $!Dial P!lan !PRI In!fo N  $!Labels! !RmoteA!ccess N  $!Back ! !Oper I!nfo S 

 

[ritelcarlos]

TOUCHTONETOMMY OR ANYONE PLEASE CHECK MY PROGRAMING

THANK YOU

 

[TravelingTom]

See Legend/Magix Initial PRI Setup
faq689-3784. I have used this guide(thanks to tek-tips) for years and have not had problems unless I miss something. You do not have a number to send programmed which could be the problem.

 

[ritelcarlos]

What of the programing would that be in

thank you

 

[TouchToneTommy]

Doing a Stare and Compare between your print outs and one of my sites that that works, the only things I see different:

Pattern 9 should be set to 9 instead of 0

My working site is set to "By extension" instead of "By Line"

I assume that you have Lines 813 through 835 in Pool 70?

Are you set to ESF, B8ZS?

From the cheat sheet: "IF YOUR CENTRAL OFFICE IS A 4ESS OR A 5ESS THE PRI SERVICE SHOULD BE AT&T CUSTOM PROTOCOL"

I'm still thinking it's on the provider's side.

 

[ritelcarlos]

THANK YOU what par of the program would i change for the 2 programs that are different

 

[TouchToneTommy]

Steps 8 and 9 in the FAQ

http://www.tek-tips.com/faqs.cfm?fid=3784

 

[ritelcarlos]

Hello,
Well i finally have everything working and you were all correct it was the provider .

I do need help on one more thing the customer is now dialing out using the PRI circuit however the carrier does not allow 800 calls to go thru i do have 8 copper lines in the system that are in group 890 and the PRI is in group 70 could someone please tell me how i can program the 800 calls to go out using pool 890.

thank you