phonedudeSr
IS-IT--Management
We are trying to install a tie line between a Nortel CS1K and a CUCM 9.X. We are having issue with getting the d-ch up. The B-channels are ok. Does anyone have the configurations or an idea of where this problem my be?
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
PRI QSig between Nortel and Cisco
- Thread starter phonedudeSr
- Start date
- Status
Splic3d
Vendor
- Dec 28, 2012
- 499
I haven't used Qsig, but for me it has always been the setting for SIDE that catches me - either usr or net. One side needs to be set as usr and the other net. Clok needs to be either EXT or INT as well.
If its not working, get a bigger hammer!
Avaya/Nortel/NEC/Asterisk/Access Control/CCTV/DSX/Acti/UCx
If its not working, get a bigger hammer!
Avaya/Nortel/NEC/Asterisk/Access Control/CCTV/DSX/Acti/UCx
ADAN DCH 13
CTYP MSDL
GRP 1
DNUM 0
PORT 2
DES CISCO
USR PRI
DCHL 44
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR YES
DIDD 0
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
DES CISCO
TN 044 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 6
RTMB 13 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID 8013
AACR NO
DATE 15 MAR 2011
NACT ****
OVL000
>ld 21
PT1000
REQ: prt
TYPE: rdb
CUST 0
ROUT 13
TYPE RDB
CUST 00
ROUT 13
DES CISCO
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00000
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
MBXR NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 8013
TCPP NO
PII NO
AUXP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
PAGE 002
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO
CTYP MSDL
GRP 1
DNUM 0
PORT 2
DES CISCO
USR PRI
DCHL 44
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR YES
DIDD 0
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
DES CISCO
TN 044 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 6
RTMB 13 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID 8013
AACR NO
DATE 15 MAR 2011
NACT ****
OVL000
>ld 21
PT1000
REQ: prt
TYPE: rdb
CUST 0
ROUT 13
TYPE RDB
CUST 00
ROUT 13
DES CISCO
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00000
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
MBXR NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 8013
TCPP NO
PII NO
AUXP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
PAGE 002
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO
NoypiToits
Vendor
Are you installing 2MB (E1) or T1 PRI card? And also check CRC protocol for both Cisco & CS1K.
Villareal
Villareal
Look at OVL 73
Print timer table :
REQ prt
TYPE pri2
FEAT lpti
LOOP xx your QSIG Loop
]MFF CRC or aff tray both
ACRC NO
ALRM REG
RAIE NO
G1OS YES
SLP 5 24 H 30 1 H
BPV 128 122
CRC 201 97
FAP 28 1
RATS 10
GP2 20 100 S 12 S 12 S 4 S
MNG1 15 M
NCG1 15 M
OSG1 15 M
MNG2 15 S
NCG2 15 S
OSG2 15 S
PERS 50
CLRS 50
OOSC 5
Print timer table :
REQ prt
TYPE pri2
FEAT lpti
LOOP xx your QSIG Loop
]MFF CRC or aff tray both
ACRC NO
ALRM REG
RAIE NO
G1OS YES
SLP 5 24 H 30 1 H
BPV 128 122
CRC 201 97
FAP 28 1
RATS 10
GP2 20 100 S 12 S 12 S 4 S
MNG1 15 M
NCG1 15 M
OSG1 15 M
MNG2 15 S
NCG2 15 S
OSG2 15 S
PERS 50
CLRS 50
OOSC 5
- Status
Similar threads
- Locked
- Question
- Question