PRI point to point and Option 11c

[hawks]

Ok I need some help, I have a point to point PRI from an Option 11C (host) to a Shurtel (remote). It is up and running I can call from the 11 to the Shurtel using my CDP and back to the Option from the Shurtel and everything works fine. My problem is they have a T1 to the outside world coming into the Opt 11 with some DID numbers that I need to go directly to the remote side. I’ve tried using the IDC and convert to my CDP numbers but when I call in the call goes to AA and never tries to go to the Shurtel. I know I’m receiving the correct info from Telco because I can point the numbers anywhere I want in the Opt 11 using the IDC table. But as soon as I tri to get them to go across the PRI that’s when mail answers.

 

[Crowd36]

Have you checked the TARGs/TGARs for the routes involved?

 

[pbxn]

Can you just use CDP's for those DID's, scratch the IDC table, and point those CDP's to your remote route?

 

[johnpoole]

that's a good point, the targs can't match on the inbound route and the tie.. the ncos of the inbound route had to be high enough to make a call to the dsc. if you dial the dsc from a set and it works, then the idc will be all you need once you have those two points looked at.. that is one reason i put tie routes in targ x1. by default trunk to trunk is blocked

john poole
bellsouth business
columbia,sc

 

[hawks]

pbxn I tried that
crowd & john I have the TGAR set to 0 (or none) but when I ort the RDB it will not show the NCOS. Now if I go and make changes the NCOS prombt is there but when I prt it don't show it. Any other way to see it or should I just change them both to 0?

 

[pbxn]

Here is my incoming route

TYPE RDB
CUST 00
ROUT 0
DES BELLSOUTH
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 3
SBN NO
PNI 00001
NCNA
NCRD YES
CHTY BCH
CPFXS YES
CPUB ON
DAPC NO
BCOT 0
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 395XX
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 1
NDNO 1 *
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 384
OGF 384
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3


PAGE 002

NBS 2048
NBL 4096

IENB 5
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA NO
OAN YES
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS YES
MRT 15
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

Here's my route for a remote site

TYPE RDB
CUST 00
ROUT 31
DES HIGHLANDS
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 395XX
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0


PAGE 002

VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA NO
OAN YES
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

 

[hawks]

Inbound to main
TYPE RDB
CUST 00
DMOD
ROUT 0
DES FLEXGROW
TKTP DID
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL 3VCE
PTYP DCO
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD xxxx
CPP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
TIMR ICF 512
OGF 512
EOD 8960
DSI 34944
NRD 10112
DDL 70
ODT 2816
RGV 640
FLH 510
GRD 896
SFB 3
TFD 0
SST 5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA NO
OAN NO
OPD NO
NATL YES
MUS YES
MRT 10
MR NO
EQAR NO
TTBL 0
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

Outbound to remote
ROUT 5
DES VOIP
TKTP DID
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
DAPC NO
BCOT 0
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD xxxx
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR NO
EQAR NO
TTBL 0
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

 

[pbxn]

The only real differance between your programming and mine, is your TARGS match, mine do not. Not sure if that is the fix or not but maybe worth a try

 

[johnpoole]

the trunk has the ncos and targ 0 matches targ 0.. perm block. do a chg of the rdb and x0

john poole
bellsouth business
columbia,sc

 

[hawks]

john I'm lost my RDB has nothing for TARG

 

[johnpoole]

that's good, nothing is not a block. couple of things to check.. RCLS EXT.. quote from your FLEXGROW tie.. that makes it an external route. a different set of rules apply to external routes.. remove the idc entry from your bs route. just the entry you need to test.. 1st forward your set to that dn and call it external then from external.. let us know how that test came out..


john poole
bellsouth business
columbia,sc

 

[hawks]

john I'm on the same page as you, I just fwd a phone on the Nortel to the remote and call into the DID # of that phone and it went to the remote.

 

[hawks]

Update: Ok I can build the DID # as an ACD and NCFW it to the remote and that works. For whatever reason I just can nopt use the IDC table, maybe it's not possible?

 

[pbxn]

Does an IDC pointed to an acd work

 

[hawks]

Yes it does

 

[carldest]

I used phantom TN's and default call forward. Here is a brief description. If you need more info let me know.

If you prt the cfn in ld22 you should see something like the following under CEQU:

SUPL 000 004 008 012
016 032 036 040
044 048 064 068
072 P096
TDS 000
CONF 029 030 031 062
094 095

DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH
TRK 01 24 ESF NO B8S FDL - 01
02 24 ESF NO B8S FDL - 01

Notice the "P" in front of 096 that means this superloop is a phantom loop. That makes cards 61, 62, 63 (and I think 64) available. Here is a sample TN that is used.

DES 2158
TN 061 0 00 00 PHANTOM
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 2158 0 MARP
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 0
XLST
SCI 0
CLS CTD DTN FBD XFD WTA THFD FND HTD ONS
LPR XRD AGRD CWD SWD MWD RMMD SMWD LPD XHD SLKD CCSD LND TVD
CFTD SFD MRD C6D CNID CLBD AUTU
ICDD CDMD LLCN EHTD MCTD
GPUD DPUD CFXA ARHD OVDD AGTD CLTD LDTD ASCD
MBXD CPFA CPTA DDGA NAMA MIND
MCRD
EXR0 SHL ABDD CFHD
USRD BNRD OCBD RTDD RBDD RBHD FAXD CNUD CNAD PGND FTTC CDMR
PLEV 02
CSDN
AACS NO
MLWU_LANG 0
FTR DCFW 16 82158

Other TN's would be 61 1, 61 2, etc., to 61 15. Then go to 62 0, 62 1, etc.

The DN is what makes the internal (to the Nortel) work. The FTR DCFW is a "default call forward". In the case of what I did on this switch, 8 is set as "AC2" in BARS that routes calls over the point to point. Then 2158 is outpulsed to my other switch and it works!!

 

[hawks]

Thanks, I got it working with the DSC and IDC table. Take a look at my other post "PRI point to point and Option 11c (part 2)" Thanks agin