PRI on Legend 4.0 (not MAGIX)

[rmelan47]

I'm trying to install a new PRI on a Legend 4.0. I have a 100D working with 24 Tie Lines.


I change from T1 to PRI and programed as normal. ATT is using a DMS-100 set as a 5ESS with ATT custom. ATT sees D-channel is in lockout. Will Legend 4.0 do PRI or do I need 4.1 or higher?



Thanks

PRI INFORMATION



System: By line

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
1 7 CallbyCall By Dial Plan

Channel ID: 1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23

Line PhoneNumber NumberToSend
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847

Network Selection Table

Entry Number: 0 1 2 3
Pattern to Match: 101**** 10***

Special Service Table

Entry Number: 0 1 2 3 4 5 6 7
Pattern to Match: 011 010 01 00 0 1
Operator: none OP OP OP/P OP none none none
Type of Number: I I I N N N N N
Digits to Delete: 0 0 0 0 0 0 0 0

Call-By-Call Service Table

Entry Number: 0 1 2 3 4
Pattern 0: 0
Pattern 1: 1
Pattern 2: 2
Pattern 3: 3
PRI INFORMATION


Pattern 4: 4
Pattern 5: 5
Pattern 6: 6
Pattern 7: 7
Pattern 8: 8
Pattern 9: 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ: No Service
DeleteDigits: 0 1 2 3 4

Entry Number: 5 6 7 8 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ:
DeleteDigits: 5 6 7 8 0

Dial Plan Routing Table

Entry Number: 0 1 2 3
NtwkServ: Any service
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 4 5 6 7
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 8 9 10 11
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 12 13 14 15
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

 

[tdaugirdas]

If AT&T is using a DMS 100 switch - then you have to set your switch-type in PRI programming to DMS 100, not 5ESS. They are incompatible - so go back into PRI programming and change your switch-type to DMS 100. Also verify that they are using NI-1 protocol vs. NI-2. NI-2 will not work.

Tom Daugirdas,
President
STCG, Inc.
stcg.com

 

[rmelan47]

Tom


Legend 4.0 does not have a choice for switch type DMS-100. Looks like an upgrade


Thanks









dms-

 

[tdaugirdas]

If you upgrade - I would go all the way to Magix R4,V7 - rather than the last Legend version.

Tom Daugirdas,
President
STCG, Inc.
stcg.com