ThePhoneMn
Vendor
Hi all,
I have a PRI on an IPOffice 9.0 that will activate, but calls drop. I have tried two different IPO's (customer and my lab system). Earthlink states they had a tech out there last week with a TBird and they were able to make calls. I scheduled a vendor meet for next week, but I want to see what you guys have to say about it. I see a PRI message I dont like, and I am concerned this is my issue.
Please let me know your thoughts. The condensed version is on this post, I will paste the entire trace next
Call Setup showing ISDN Protocol Q.931, dialing 7815551212, sending outbound CID 6175551212
11:52:27 158052mS ISDNL3Evt: v=1 stacknum=1 State, new=Initiated, old=NullState id=1006
11:52:27 158053mS ISDNL3Tx: v=1 peb=1
ISDN Layer3 Pcol=08(Q931) Reflen=2 ref=0001(Remote)
Message Type = Setup
InformationElement = BearerCapability
0000 04 03 90 90 a2 .....
InformationElement = CHI
0000 18 03 a9 83 97 .....
InformationElement = CallingPartyNumber
0000 6c 0c 21 80 36 31 37 34 32 33 34 33 30 30 l.!.6175551212
InformationElement = CalledPartyNumber
0000 70 0c a0 31 37 38 31 35 38 35 34 31 32 36 p..17815551212
11:52:27 158053mS ISDNL2Tx: v=1 peb=1
0000 00 01 00 00 08 02 00 01 05 04 03 90 90 a2 18 03 ................
0010 a9 83 97 6c 0c 21 80 36 31 37 34 32 33 34 33 30 ...l.!.6175551212
0020 30 70 0c a0 31 37 38 31 35 38 35 34 31 32 36 0p..17815551212
11:52:27 158055mS ISDNL1Tx: v=1 peb=1
0000 00 01 00 00 08 02 00 01 05 04 03 90 90 a2 18 03 ................
0010 a9 83 97 6c 0c 21 80 36 31 37 34 32 33 34 33 30 ...l.!.6175551212
0020 30 70 0c a0 31 37 38 31 35 38 35 34 31 32 36 0p..17815551212
Call handling, with a receive message “Call Proceeding” from Earthlink’s Adtran
11:52:27 158082mS ISDNL1Rx: v=1 peb=1
0000 02 01 00 02 08 02 80 01 02 18 03 a9 83 97 ..............
11:52:27 158083mS ISDNL2Rx: v=1 peb=1
0000 02 01 00 02 08 02 80 01 02 18 03 a9 83 97 ..............
11:52:27 158083mS ISDNL3Rx: v=1 peb=1
ISDN Layer3 Pcol=08(Q931) Reflen=2 ref=0001(Local)
Message Type = CallProceeding
InformationElement = CHI
The next message should be “Alerting” which shows the other end ringing. Instead we send a Release
11:52:27 158101mS ISDNL3Tx: v=1 peb=1
ISDN Layer3 Pcol=08(Q931) Reflen=2 ref=0001(Remote)
Message Type = Release
Been there, done that
I have a PRI on an IPOffice 9.0 that will activate, but calls drop. I have tried two different IPO's (customer and my lab system). Earthlink states they had a tech out there last week with a TBird and they were able to make calls. I scheduled a vendor meet for next week, but I want to see what you guys have to say about it. I see a PRI message I dont like, and I am concerned this is my issue.
Please let me know your thoughts. The condensed version is on this post, I will paste the entire trace next
Call Setup showing ISDN Protocol Q.931, dialing 7815551212, sending outbound CID 6175551212
11:52:27 158052mS ISDNL3Evt: v=1 stacknum=1 State, new=Initiated, old=NullState id=1006
11:52:27 158053mS ISDNL3Tx: v=1 peb=1
ISDN Layer3 Pcol=08(Q931) Reflen=2 ref=0001(Remote)
Message Type = Setup
InformationElement = BearerCapability
0000 04 03 90 90 a2 .....
InformationElement = CHI
0000 18 03 a9 83 97 .....
InformationElement = CallingPartyNumber
0000 6c 0c 21 80 36 31 37 34 32 33 34 33 30 30 l.!.6175551212
InformationElement = CalledPartyNumber
0000 70 0c a0 31 37 38 31 35 38 35 34 31 32 36 p..17815551212
11:52:27 158053mS ISDNL2Tx: v=1 peb=1
0000 00 01 00 00 08 02 00 01 05 04 03 90 90 a2 18 03 ................
0010 a9 83 97 6c 0c 21 80 36 31 37 34 32 33 34 33 30 ...l.!.6175551212
0020 30 70 0c a0 31 37 38 31 35 38 35 34 31 32 36 0p..17815551212
11:52:27 158055mS ISDNL1Tx: v=1 peb=1
0000 00 01 00 00 08 02 00 01 05 04 03 90 90 a2 18 03 ................
0010 a9 83 97 6c 0c 21 80 36 31 37 34 32 33 34 33 30 ...l.!.6175551212
0020 30 70 0c a0 31 37 38 31 35 38 35 34 31 32 36 0p..17815551212
Call handling, with a receive message “Call Proceeding” from Earthlink’s Adtran
11:52:27 158082mS ISDNL1Rx: v=1 peb=1
0000 02 01 00 02 08 02 80 01 02 18 03 a9 83 97 ..............
11:52:27 158083mS ISDNL2Rx: v=1 peb=1
0000 02 01 00 02 08 02 80 01 02 18 03 a9 83 97 ..............
11:52:27 158083mS ISDNL3Rx: v=1 peb=1
ISDN Layer3 Pcol=08(Q931) Reflen=2 ref=0001(Local)
Message Type = CallProceeding
InformationElement = CHI
The next message should be “Alerting” which shows the other end ringing. Instead we send a Release
11:52:27 158101mS ISDNL3Tx: v=1 peb=1
ISDN Layer3 Pcol=08(Q931) Reflen=2 ref=0001(Remote)
Message Type = Release
Been there, done that