PRI channel lockout

[Telco01]

Recently installed 2 PRI circuits coming from a DMS100 to an Opt81C. 2 PRI's 2 DCH's. Trunks are going into lockout occasionaly. I try and disable and reenable channel and it stays locked out. It will free up if the DMS tech "posts" the channel. Can someone tell me if I should change my programing?

Thanx


TYPE RDB

CUST 00

ROUT 7

DES CTC

TKTP DID

M911_ANI NO

M911_TONE NO

NPID_TBL_NUM 0

SAT NO

RCLS EXT

VTRK NO

DTRK YES

BRIP NO

DGTP PRI

ISDN YES

MODE PRA

IFC NI2

CBCR NO

NCOS 0

SBN NO

PNI 00001

NCNA YES

NCRD YES

CHTY BCH

CPFXS YES

CPUB OFF

DAPC NO

BCOT 0

INTC NO

DSEL 3VCE

PTYP PRI

AUTO NO

DNIS NO

DCDR NO

ICOG IAO

RANX NO

SRCH LIN

TRMB YES

STEP

ACOD 1007

TCPP NO

PII NO

TARG 07 08 09

CLEN 1

BILN NO

OABS

INST

IDC NO

DCNO 0 *

NDNO 0

DEXT NO

ICIS YES

TIMR ICF 512

OGF 512

EOD 13952

NRD 10112

DDL 70

ODT 4096

RGV 640

FLH 510

GRD 896

SFB 3

NBS 2048

PAGE 002

NBL 4096

IENB 5

VSS 0

VGD 6

DRNG NO

CDR YES

INC YES

LAST YES

QREC NO

OAL YES

AIA NO

OAN YES

OPD NO

CDRX NO

NATL YES

VRAT NO

MUS YES

MRT 4

RACD NO

EQAR NO

FRL 0 0

FRL 1 0

FRL 2 0

FRL 3 0

FRL 4 0

FRL 5 0

FRL 6 0

FRL 7 0

OHQ NO

OHQT 00

TDET NO

TTBL 0

ATAN NO

PLEV 2

MCTS NO

ALRM NO

ART 0

SGRP 0

AACR NO
---------------------------------------------
ADAN DCH 7

CTYP MSDL

GRP 0

DNUM 10

PORT 2

DES 3rd-CTC-T-1

USR PRI

DCHL 2

OTBF 32

PARM RS422 DTE

DRAT 64KC

CLOK EXT

IFC NI2

ISDN_MCNT 300

CLID OPT0

CO_TYPE ATT

SIDE USR

CNEG 1

RLS ID 1

RCAP COLP

MBGA NO

OVLR NO

OVLS NO

T310 120

T200 3

T203 10

N200 3

N201 260

K 7

BSRV NO

 

[kprintz]

I'd change your IFC value (RDB and ADAN) to D100 if you are interfacing to a DMS 100.

 

[telecomnorth]

Make sure your T-1/DS-1 is running clean.

You have CO_type set to ATT in the D-Channel. Verify that the CO is a 5ESS otherwise set to STD for Nortel CO's. Also the RLS ID = 1 does not look right. With Nortel CO's this is usually set for 36 which may be wrong but likely better than 1. Not sure about 5ESS/ATT CO's.

 

[Telco01]

Will we loose NI-2 functionality by mmaking the IFC=D100 in the RDB?

 

[Reusser]

telecomnorth (TechnicalUser) 7 Feb 06 21:26
Make sure your T-1/DS-1 is running clean.

You have CO_type set to ATT in the D-Channel. Verify that the CO is a 5ESS otherwise set to STD for Nortel CO's. Also the RLS ID = 1 does not look right. With Nortel CO's this is usually set for 36 which may be wrong but likely better than 1. Not sure about 5ESS/ATT CO's


Did you do the above? you said you are cnnected to DMS100 but your Dchannel indicate NI2 with AT&T switch.

Also verify DMS100 is setup for NI2 and Turn off Serv if it is on.

LD 96
stat serv

dis serv 7

 

[Telco01]

Not sure if the DMS100 is set up for NI2 or not..will check tomorrow...not sure if I can set IFC for D100 and NI-2. Will be back.

 

[armytechie]

I seen this same issue recently...Check this thread.

http://www.tek-tips.com/viewthread.cfm?qid=1185260&page=1

 

[Telco01]

Changed Dchl to CO_Type=STD and RlsID=36 per Reusser. I changed this on Friday, so far so good, will update in a couple days.

 

[Telco01]

2/13/06 didn't really help. Today 2/21/06 found out that when interfacing with a DMS100 there is a command on the D-channel set up that lets the DMS and the Opt81C talk to each other. When my channel showed LCKO the DMS showed idle and vicea versa. I turned on BSRV in the D-channel programing and the DMS and PBX are talking back and forth. Hopefully this is the fix. Maybe someday Nortel will be able to make is simple to program an Opt PBX to a DMS.

 

[aball]

in your adan progframing try setting rls id to 36 for dms100

 

[PBXYoda]

You may want to verify with your CO that they're not on DAX switch. They always tell you that they're on a DMS-100 configured off of a DAX. When this happens they either need to configure you on a real DMS-100, or the only other fix is to turn on services on the D-channel. However you will still get slips. Hope this helps.

 

[Telco01]

0n 2/27/06 I turned on ENL SERV in LD96 and this along with BSRV on the d channel programming has enabeled me to turn channels back up if the are anything but idle.