PRI 226 alarms

[jkaval]

PRI0226
Protocol Error: No RESTart ACK message received. Output data: DCH: x
DATA: y . Where: x = D-channel number and y = UTN.
Contact your technical support group if the problem persists.
Severity: Critical

What would be causing this? When I reset the DCH it seems to clear up for a couple days. The errors are on a TIE to a Cisco Call Manager. I'll put the programming below.

TYPE TIE TRUNK
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 5
RTMB 30 24
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 13 JAN 2009

ADAN DCH 6 DCH
CTYP MSDL
GRP 1
DNUM 14
PORT 3
DES CISCOIP
USR PRI
DCHL 90
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100
SIDE USR
CNEG 1
RLS ID 26
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7


TYPE RDB ROUTE
CUST 00
ROUT 30
DES CISCOIP
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 00000
NCNA YES
NCRD YES
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
MBXR NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD XXXXX
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3


PAGE 002

NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST YES
QREC YES
OAL YES
AIA NO
OAN YES
OPD NO
CDRX NO
NATL YES
VRAT NO
MUS YES
MRT 15
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

 

[DocVic]

Is your IFC really D100? Is it configured that way on the other end?

DocVic
Dedicated to Nortel Products till the end.
Need help?

http://www.TSS-CO.com

 

[jkaval]

Yes. That is the way the vendor for the Call Manager wanted it.

 

[PERRYPJ]

Only way I have ever set them up is QSIG,

ADAN DCH 100
CTYP MSDL
GRP 0
DNUM 13
PORT 0
DES Cisco
USR PRI
DCHL 0
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR YES
DIDD 0
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7


OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[pronei]

Use QSIG, DMS-100 Emulation tells the Nortel PBX that it is connecting to a DMS 100, send signaling accordingly.

http://www.linkedin.com/in/neil74/

 

[Reusser]

Cisco has a PDF for DMS100 on call manager side and SL100 on meridian PBX side.

If you can not do Qsig I have used this option successfully

 

[jkaval]

I can look into the QSIG, but the weird thing is we have two programmed the same, but only one has the issue. Could we get those errors from a possible bad cable?