prefix 0032 md110 to local conversations 3

[zibi11]

I have trouble from prefix 0032 + number for local conversations
it was 0 + number for local conversations
How to solve this ?????

how to restore 0 +local number

NUMBER ANALYSIS DATA

TYPE OF SERIES NUMBER SERIES

EXTENSION NUMBER SERIES 501 - 598
600 - 798

EXTERNAL DESTINATION CODE 1990 - 1999
4

LEAST COST ROUTING ACCESS
CODE NUMBER SERIES 0

OPERATOR INDIV. NUMBER SERIES 599

OPERATOR COMMON NUMBER SERIES 9

OPERATOR COM. DID. NUM. SERIES 500

DIRECT INWARD SERVICE ACCESS 799

TYPE OF SERVICE CODE SERVICE CODE

ANSWER GROUP CALL PICK UP 8

EXTERNAL NUMBER LENGTH DATA

EXTERNAL NUMBER NUMBER LENGTH

000 11

001 7 - 12
002 7 - 12
003 7 - 12
004 7 - 12
005 7 - 12
006 7 - 12
007 7 - 12
008 7 - 12
009 7 - 12
01 7 - 8
02 7 - 8
03 7 - 8
04 7 - 8
05 7 - 8
06 7 - 8
07 7 - 8
08 7 - 8
09 4 - 8

PROCEED TO SEND SIGNAL DATA

EXTERNAL NUMBER POS. TYPE

00 02 - C
40 02 - C

CALL DISCRIMINATION DATA

EXTERNAL/INTERNAL NUMBER CAT

000 3

001 3 2

002 3 2

003 3 2

004 3 2

005 3 2

006 3 2

007 3 2

008 3 2

009 3 2

01 3 2 1

02 3 2 1

03 3 2 1

04 3 2 1

05 3 2 1

06 3 2 1

07 3 2 1

08 3 2 1

09 3 2 1 0

5 3 2 1 0

6 3 2 1 0

7 3 2 1 0

8 3 2 1 0

9 3 2 1 0
END

 

[fouesnant]

Hi

Your access code 0 goes to LCR.
You need to printout the LCR data's
LCDDP:TAB=ENT;
LCDDP:TAB=FDT;
LCDDP:TAB=DNT1;
LCDDP:TAB=DNT2;
LCLDP:LIM=ALL;
and RODDPEST=ALL;

to analyze what's going on you dialling 0032

 

[zibi11]

<LCDDP:TAB=ENT;
LEAST COST DESTINATION DATA

EXTERNAL NUMBER TABLE

ENTRY TRC PRE CONF

0 1 0 N
END

<LCDDP:TAB=NLT;
NOT ACCEPTED
ENTRY NOT FOUND

<LCDDP:TAB=DNT1;
LEAST COST DESTINATION DATA

EXCEPTIONS TABLE

ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA

0050 2 0 3 111111111111111 0
0060 2 0 3 111111111111111 0
0069 2 0 3 111111111111111 0
0088 2 0 3 111111111111111 0
0090 2 0 3 111111111111111 0
END

<LCDDP:TAB=DNT2;
LEAST COST DESTINATION DATA

NUMBER TABLE

ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA

0 1 0 2 111111111111111 0
END

<LCDDP:TAB=FDT;
LEAST COST DESTINATION DATA

FICTITIOUS DESTINATION TABLE

FRCT PRE

2 1990
3 1993
4 1991
END

<LCDDP:TAB=PNR;
NOT ACCEPTED
ENTRY NOT FOUND

<LCDDP:TAB=RCT;
NOT ACCEPTED
FRCT-VALUE
NOT ASSIGNED
<SPEXPIR=ALL;
NOT ACCEPTED
DIR
NOT ASSIGNED
<

 

[zibi11]

LCDDP:TAB=ENT;
LEAST COST DESTINATION DATA

EXTERNAL NUMBER TABLE

ENTRY TRC PRE CONF

0 1 0 N
END

<LCDDP:TAB=FDT;
LEAST COST DESTINATION DATA

FICTITIOUS DESTINATION TABLE

FRCT PRE

2 1990
3 1993
4 1991
END

<LCDDP:TAB=DNT1;
LEAST COST DESTINATION DATA

EXCEPTIONS TABLE

ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA

0050 2 0 3 111111111111111 0
0060 2 0 3 111111111111111 0
0069 2 0 3 111111111111111 0
0088 2 0 3 111111111111111 0
0090 2 0 3 111111111111111 0
END

<LCDDP:TAB=DNT2;
LEAST COST DESTINATION DATA

NUMBER TABLE

ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA

0 1 0 2 111111111111111 0
END

<LCLDP:LIM=ALL;
NOT ACCEPTED
AC/DEST
NOT ASSIGNED
<LCDDP:LIM=ALL;
NOT ACCEPTED
MISSING PARAMETER
TAB
<RODDPEST=ALL;
EXTERNAL DESTINATION ROUTE DATA

DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE

0 52 0025000000000250 0 2 0
51 1 0025000000000250 0 2 0
1990 52 0005000000000250 0 5 0
51 1 0005000000000250 4 5 0 1990
1991 51 0005000000000250 0 5 0
1993 40 1005000000000250 0 5 0
52 1 0005000000000250 4 5 0 19900
51 2 0005000000000250 4 5 0 19900
1994 44 0005000000000250 0 5 0
2 30 0005000000000250 0 1 0
3 20 0005000000000250 0 1 0
4 5 0005000000000250 0 2 0
90 52 0025000000000250 0 3 0
91 2 0005000000000250 0 3 0
96 92 0005000000000250 0 3 0
97 93 0005000000000250 0 3 0
98 90 1005000010000250 0 3 0
99 91 1005000010000250 0 3 0

END

 

[cfrei]

Hi Zibi11,
can you define, what you exactly want?

I don't understand ENT.
First you delete leading 0 and after that you add 0 again?

 

[fouesnant]

Hello

As far as I understand from your data

1/To dial out every one should dial at least 00. Dialling only 0 will go nowhere as :
first 0 is removed in ENT
If the dialled number does not find any match in DNT1 go to DNT2
in DNT2 if dialled number is not 0, then it should endup in LCLDP table but nothing is defined there, so I guess that you get "Vacant Number"

2/dialling 00050, 00060, 00069, 00088, 00090 will end up with DEST 1993 ans send toward that route 50, 60, 69 and 90 as first part of the dialling number:
first zero is removed in ENT
2 following zero will be removed in DNT1

3/Now your dialling 0032 is not defined anywhere
SO after ENT table (remove one zero) and DNT1 table (no match there continue with DNT2) and finally DNT2 table (remove one zero), the number 32 is sent over the route 52 via DEST 1990.

Is it really what you want ?
I am not able to say where it should go.

 

[zibi11]

Hello

Actually local conversations ring { 0 + local number} for cat 1
My telephone operator change local ring
from 5 December change local conversations ring { 0 + 032 +local number} for cat 1

I made
NACDR:NUM=003;
NACDS:NUM=0032,CDCAT=1&&3;
NACDS:NUM=0033&0034,CDCAT=2&3;

Problem in this prefix ( 032 )
0 +032 + local number
I would like
0 +local number

 

[zibi11]

when I ring 0 + local number (cat 1)-- my md110 saw as 0 +032 + number

 

[zibi11]

I want when I ring local number outside {0 + local number} (cat 1)-- my md110 saw as {0 +032 + number}

0 2106533 local number outside before change
I made

NACDR:NUM=003;
NACDS:NUM=0032,CDCAT=1&&3;
NACDS:NUM=0033&0034,CDCAT=2&3;

0 032 2106533 local number outside after change for my telephone operator 5 December 2005


I want ring 5 December 2005 so as before 0 2106533 for cat1
what will I change

 

[zibi11]

correct!!!!!!!!!



How to add to local numbers start at 2,3,4,5,6,7,and 8 prefix 032 to local number for 1,2,3 cat

 

[lalrl]

lcddi:tab=ent,entry=02,trc=1,pre=0032;
.
.
lcddi:tab=ent,entry=08,trc=1,pre=0032;

Means, that a user will dial: 0 2106533
MD will dial instead: 0 032 2106533

 

[cfrei]

Hi
other possible solution:

Clear DNT2
LCDDI:tab=dnt2,entry=0,trc=1,pre=032;

All numbers, which goes thru this table till now, should be prefixed 032.

But what happen, when subscriber dial number correctly?
You have to add line in DNT1

LCDDI:tab=dnt1,entry=0032,trc=1,frct=2;

If you use ENT table, you can't disable dialing your own exchange number thru the operator.

This solution was not tested.

For fouesnant
Maybe I'm wrong, but if you look on programming ENT, (message 11:39) there is entry=0, trc=1,pre=0. In my opinion, there is cleared leading 0 and immediately add again.

 

[zibi1]

When I write
lcddi:tab=ent,entry=03,trc=1,pre=0032;

Md110 write
NOT ACCEPTED
REDUNDANT ENTRY

???

 

[cfrei]

lcddp:tab=ent;

 

[zibi1]

LCDDP:TAB=ENT;
LEAST COST DESTINATION DATA

EXTERNAL NUMBER TABLE

ENTRY TRC PRE CONF

0 1 0 N
END

<LCDDP:TAB=NLT;
NOT ACCEPTED
ENTRY NOT FOUND

<LCDDP:TAB=DNT1;
LEAST COST DESTINATION DATA

EXCEPTIONS TABLE

ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA

0050 2 0 3 111111111111111 0
0060 2 0 3 111111111111111 0
0069 2 0 3 111111111111111 0
0088 2 0 3 111111111111111 0
0090 2 0 3 111111111111111 0
END

 

[cfrei]

You can't use ENT, because there is entry 0. In this case is not possible use ENTRY 0xxx. Take my advice and forgot ENT. Do everthing in DNT1 and DNT2. ENT is bad programmed, because it block entry 0 and has no reason. If you delete it, nothing happend.
ENT table is good, when you want delete prefix for your exchange. It means, when extension want dial another extension a dial complete public number, in ENT is public number deleted and only extesion number is dialled.
Now all number, except 0050,0060,0069,0088 and 0090 goes thru DNT2. If you want prefix this other numbers with 032, you have to put this prefix into DNT2.
But as I wrote, you have to make possible dialling both type of dialling. Subcriber can dial 0+local number (translated to 0+032+local number) and 0+032+local number from his telephone.

 

[cfrei]

Last solution - tested

LCDDE:TAB=DNT2;
LCDDI:TAB=DNT2,ENTRY=0,TRC=1,PRE=032,FRCT=2;

LCDDI:TAB=DNT1,ENTRY=0032,TRC=1,FRCT=2;

LCDDE:TAB=ENT;

 

[zibi1]

Hello

Thank you for all ,you are the best!!!!!!!!!

 

[zibi1]

After change

LCDDP:TAB=ENT;
LEAST COST DESTINATION DATA

EXTERNAL NUMBER TABLE

ENTRY TRC PRE CONF

00 1 0 N
01 1 0 N
02 1 0032 N
03 1 0032 N
04 1 0032 N
05 1 0032 N
06 1 0032 N
07 1 0032 N
08 1 0032 N
09 1 0 N
END

<LCDDP:TAB=FDT;
LEAST COST DESTINATION DATA

FICTITIOUS DESTINATION TABLE

FRCT PRE

2 1990
3 1993
4 1991
END

<LCDDP:TAB=DNT1;
LEAST COST DESTINATION DATA

EXCEPTIONS TABLE

ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA

0050 2 0 3 111111111111111 0
0060 2 0 3 111111111111111 0
0069 2 0 3 111111111111111 0
0088 2 0 3 111111111111111 0
0090 2 0 3 111111111111111 0
END

<LCDDP:TAB=DNT2;
LEAST COST DESTINATION DATA

NUMBER TABLE

ENTRY TRC PRE ACCT FRCT TOLL CBCS BTON TNS OSA

0 1 0 2 111111111111111 0
END

<LCLDP:LIM=ALL;
NOT ACCEPTED
AC/DEST
NOT ASSIGNED
<RODDPEST=ALL;
EXTERNAL DESTINATION ROUTE DATA

DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE

0 52 0025000000000250 0 2 0
51 1 0025000000000250 0 2 0
1990 52 0005000000000250 0 5 0
51 1 0005000000000250 4 5 0 1990
1991 51 0005000000000250 0 5 0
1993 40 1005000000000250 0 5 0
52 1 0005000000000250 4 5 0 19900
51 2 0005000000000250 4 5 0 19900
1994 44 0005000000000250 0 5 0
2 30 0005000000000250 0 1 0
3 20 0005000000000250 0 1 0
4 5 0005000000000250 0 2 0
90 52 0025000000000250 0 3 0
91 2 0005000000000250 0 3 0
96 92 0005000000000250 0 3 0
97 93 0005000000000250 0 3 0
98 90 1005000010000250 0 3 0
99 91 1005000010000250 0 3 0

END

 

[cfrei]

Please,try this:
Dial from extension 0+local number another extension.

Then CTDEIIR=calling extension.

Is this extension connect to outgoing trunk or directly to another extension?