Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Pix 501 and PCAnywhere

Status
Not open for further replies.
bigdog175

bigdog175

IS-IT--Management
Nov 7, 2000
41
US
I'm connecting to the PIX using VPN client 4.6 but I'm unable to connect to my pcanywhere host residing on the LAN at 192.168.1.10 I have a similar setup at another location and it works fine???? Also is this config secure is there anything that could make it more secure? Thanks for any help in advance.

Here's the config:

PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 9iGf8EHeeX5FE8W7 encrypted
passwd 9iGf8EHeeX5FE8W7 encrypted
hostname pixfirewall
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside pppoe setroute
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool ippool 192.168.2.1-192.168.2.10
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
crypto ipsec transform-set myset esp-3des esp-md5-hmac
crypto dynamic-map dynmap 10 set transform-set myset
crypto map mymap 10 ipsec-isakmp dynamic dynmap
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap interface outside
isakmp enable outside
isakmp identity address
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption 3des
isakmp policy 10 hash md5
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
vpngroup xxx address-pool ippool
vpngroup xxx split-tunnel 101
vpngroup xxx idle-time 1800
vpngroup xxx password ********
telnet 192.168.1.0 255.255.255.0 inside
telnet timeout 15
ssh timeout 5
console timeout 0
vpdn group pppgrp request dialout pppoe
vpdn group pppgrp localname xxx
vpdn username xxx password *********
dhcpd address 192.168.1.100-192.168.1.130 inside
dhcpd dns xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside
terminal width 80
 
Sort by date Sort by votes
Where is your nat 0 statement for no nat from your internal hosts to your VPN clients?
 
Upvote 0 Downvote
Ok, Need to re-visit this post again. I have added nat 0 access-list 101 to the config I'm still having the same issues the VPN tunnel connects authenticates but I cannot access any of the remote LAN resources from the VPN client using Ver (4.6.00.0039) I have the identical setup at other sites this is the only one that doesn't work and the configs look identical Please HElp
 
Upvote 0 Downvote
PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password owtGs6KjDVnHn encrypted
passwd jDUXMyxQIVgK encrypted
hostname pixfirewall
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list 101 permit ip 192.168.10.0 255.255.255.0 192.168.2.0 255.255.255.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside x.x.x.x 255.255.255.224
ip address inside 192.168.10.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list 101
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
route outside 0.0.0.0 0.0.0.0 z.z.z.z
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set myset esp-des esp-md5-hmac
crypto dynamic-map dynmap 10 set transform-set myset
crypto map mymap 10 ipsec-isakmp dynamic dynmap
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap interface outside
isakmp enable outside
isakmp identity address
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption des
isakmp policy 10 hash md5
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
telnet 192.168.10.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.10.100-192.168.10.130 inside
dhcpd dns x.x.x.x y.y.y.y
dhcpd lease 86400
dhcpd ping_timeout 750
dhcpd enable inside
terminal width 80
 
Upvote 0 Downvote
Hi,

Are you trying to connect from behind another NAT device ? I can't see a 'isakmp nat-t' command in your config.

Regards Colin.
 
Upvote 0 Downvote
You have no line in the ACL 101 that would include 192.168.1.10 in your nat 0.
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

Sameer258
  • Locked
  • Question
Need Help to Find ip and mac address with email who one open my email
Replies
0
Views
289
Sameer258
Sameer258
Tommy_T
  • Locked
  • Question
Sonic wall - Have an issue remotely connectioning VNC and SMB (and AFP) to one of the 2 ISP circuits
Replies
1
Views
247
nnaarrnn
nnaarrnn
Nitta84
  • Locked
  • Question
navigation slow and tcp syc/ack drop
Replies
0
Views
209
Nitta84
Nitta84
xwray
  • Locked
  • Question
PIX 501 DHCP Server function
Replies
0
Views
61
xwray
xwray
brownmab53
  • Locked
  • Question
PIX 525 ASA not allowing DHCP addresses to pass through to router
Replies
0
Views
71
brownmab53
brownmab53

Part and Inventory Search

Sponsor

Back
Top