Phantom forward not going to mailbox 1

[9belowzero]

I have setup a Phantom forward from a 500PH to a 3904 TN which works fine however if the 3904 does not pickup it just rings as does not go to the 3904's mailbox. However if you call the 3904's DN it goes to VM fine.

500PH DN (2854) Forwards to 3854
3904 DN 3854

I have also added both these DN's to the user VM box in CallPilot.

What am i missing ?

Thanks

 

[GHTROUT]

Set the FDN on the Phantom. It should be the same FDN that is on the 3904 TN.

The FDN instructions are received from the originally dialed DN, which is the Phantom DN in your case.

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[9belowzero]

CHG
TYPE: 500
MARP NOT ACTIVATED
TN 96 0 1 2
PHANTOM
ECHG yes
ITEM FDN SCH0101

:-(

 

[GHTROUT]

I would work on turning MARP on some day, but for this, we can still get it going:

CHG
TYPE: 500
MARP NOT ACTIVATED
TN 96 0 1 2
PHANTOM
ECHG yes
[red]ITEM CLS FNA[/red]
ITEM FDN (the FDN)

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[GHTROUT]

Ooops

CHG
TYPE: 500
MARP NOT ACTIVATED
TN 96 0 1 2
PHANTOM
ECHG yes
ITEM CLS FNA
ITEM [red]FTR[/red] FDN (the FDN)

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[9belowzero]

Still get SCH code even after adding FNA, full TN:

REQ: prt
TYPE: tnb


MARP NOT ACTIVATED

TN 96 0 1 2
DATE
PAGE
DES

DES PHANT
TN 096 0 01 02 PHANTOM
TYPE 500
CDEN 4D
CUST 0
ERL 00000
WRLS NO
DN 2854 0 MARP
CPND
CPND_LANG ROMAN
NAME Randolph Burt
XPLN 27
DISPLAY_FMT FIRST,LAST
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 0
XLST
SCI 0
SCPW
SFLT NO
CAC_MFC 0
CLS CTD DTN FBD XFD WTA THFD FNA HTD ONS
LPR XRD AGRD CWD SWD MWD RMMD SMWD LPD XHD SLKD CCSD LND TVD
CFTD SFD MRD C6D CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUD DPUD CFXD ARHD OVDD AGTD CLTD LDTD ASCD SDND
MBXD CPFA CPTA UDI RCC HBTD IRGD DDGA NAMA MIND
NRWD NRCD NROD SPKD CRD PRSD MCRD
EXR0 SHL ABDD CFHD DNDY DNO3
CWND USRD BNRD OCBD RTDD RBDD RBHD FAXD CNUD CNAD PGND FTTC
FDSD NOVD CDMR MCDD T87D PKCH MPTD
RCO 0
PLEV 02
AACS NO
MLWU_LANG 0
FTR DCFW 4 3854
DATE 8 MAY 2009

Looking at it should hunt be set to 8000 (Call Pilot) or the TN i am forwarding to ?

Thanks

 

[GHTROUT]

Then you're not adding it correctly:

Let's say the FDN of the 3904 set was 6245 and you wanted to add that FDN to the phantom too:

CHG
TYPE: 500
MARP NOT ACTIVATED
TN 96 0 1 2
PHANTOM
ECHG yes
ITEM CLS FNA
ITEM FTR FDN 6245



[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[GHTROUT]

Also, HUNT does not apply to Phantoms, since they are never busy.

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[9belowzero]

Ok the FDN on the 3904 is 8000 (call Pilot route), however as soon as you hit the space key after typing FND on the phantom you get the SCH code so it is not even possible to enter a number.

Cheers

 

[GHTROUT]

Then type the words EXACTLY as I wrote, don't pick your own mnemonics.

[red]ITEM FTR FDN 8000[/red]

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[9belowzero]

Doh, that worked Thanks for your help.

 

[GHTROUT]

Excellent!

Remember, on analog/500 TNs, a variety of capabilities are stuck in the "FTR" section. You can see a list of them under "F" for FTR in the books with LD 10

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators