paging Mr. johnpoole ... BRI code posting for videocnf

[tsinc]

Hi John,

We traded posts last week regarding my issue with Meridian OP11C BRI out PRI to connect 2 Polycom videoconference systems.

I'm posting my code below - please let me know if you see anything incorrect.

As mentioned, when I'm dialing from the Polycom to setup the vc call, everything seems to look great - ie. it 'connects' to far end (I get connect ack when monitoring the d channel msgs), I monitor the b channels and both are in busy state, I monitor from the Ascend IMUX and they say 'dialing' ... 'connecting' ... then 'online 64K' - I'm sitting there holding my breath waiting for a picture to pop up on the screen. But it holds in this state for about 10 seconds - then disconnects.

Code as follows:

MISP:

REQ PRT
TYPE MISP
LOOP 5

LOOP 3
APPL BRIL
DPSD NO
CARD1 5 0 0
CARD2
CARD3
CARD4

DSL:

TN 5 0 0 0
DES BRI1
CUST 0
CTYP UILC
OPT BRIL
MISP 3
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 1
PRID 6
PDCA 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 3
SGRP 0
CLS UNR ICDD CDMD MRD ABDD PGND BRTD
DATE 4 MAY 2007

TN 5 0 0 1
DES BRI2
CUST 0
CTYP UILC
OPT BRIL
MISP 3
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 1
PRID 6
PDCA 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 3
SGRP 0
CLS UNR ICDD CDMD MRD ABDD PGND BRTD
DATE 4 MAY 2007

TN 5 0 0 2
DES BRI3
CUST 0
CTYP UILC
OPT BRIL
MISP 3
B1CT VCE DTA
B2CT VCE DTA
LDN 1
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 1
PRID 6
PDCA 1
FDN
EFD
HUNT
EHT
TGAR 1
NCOS 3
SGRP 0
CLS UNR ICDD CDMD MRD ABDD PGND BRTD
DATE 7 MAR 2007

TSP (I've only programmed one TSP so far - I was going to program the other 2 when I get one of them tested and working). Also, the SPIDs are DIDs on the PRI (I've changed them here as this is a public post), and the DNs are just spare DNs that I assigned in the Option 11):

REQ PRT
TYPE TSP
DSL 5 0
OPT

USID 1
MPHC NO
SPID 9055551212

DN 5529 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD
SSRV_NI

DFDN 5529

USID 2
MPHC NO
SPID 9055551213

DN 5531 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD
SSRV_NI

DFDN 5531

And when I stat it, it gives me this:

.STAT 5

SW DSL L2 #TEI L1 D-CHANNEL RCVY CLK MODE
==== ==== ==== ==== ==== ========= ==== ==== ====
00 = IDLE LINE ESTA 2 UP
01 = IDLE LINE RLS 0 DOWN
02 = IDLE LINE RLS 0 DOWN
03 = UNEQ
04 = UNEQ
05 = UNEQ
06 = UNEQ
07 = UNEQ

... which looks great for the BRI.

PRI programming is below:

RDB:

TYPE RDB
CUST 00
DMOD
ROUT 80
DES PRI_NI1
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 00000
NCNA YES
NCRD YES
CHTY BCH
ISAR NO
IEC ???
CPUB OFF
DAPC NO
BCOT 0
DSEL VOD
PTYP PRI
AUTO NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 7180
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
NBS 2048
NBL 4096
TFD 0
LEXT 100
DRNG NO
CDR NO
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

CHANNEL PROGRAMMING:

REQ: PRT
TYPE: TNB
TN 4 1
DATE
PAGE
DES

DES PRI_NI1
TN 004 01
TYPE COT
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 3
RTMB 80 1
B-CHANNEL SIGNALING
NITE
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD
P10 VNL
TKID
AACR NO
DATE 7 MAR 2007

D-CHANNEL PROGRAMMING:

ADAN DCH 5
CTYP MSDL
CARD 04
PORT 1
DES
USR PRI
DCHL 4
OTBF 127
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100
SIDE USR
CNEG 1
RLS ID **
RCAP
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

Please let me know if there is anything else I can show to assist in troubleshooting.

Just a comment as well - as mentioned I only have one of the TSP's programmed for testing, so I'm trying to connect to the far end Polycom at 128K. The far end Polycom has 4 BRIs, so it's capacity is 512K. Would there be an issue connecting between 2 systems having different BRI pipe sizes? I wouldn't think so - I would think it would just connect at the lower speed. But maybe I need to connect 1 or 2 more BRIs to get connect ... possible? Also, for the SPIDs ... what is the significance of them? Can I just put any number in there? Or are they actually used in call setup? Are they used for inbound, outbound, or both?

Thanks all - any help that can be provided is greatly appreciated!!

 

[EddieDuece]

JP is on vacation for 2 weeks, but my money says you'll hear from him before then!

 

[johnpoole]

you win eddie.. does that spid give you a problem.. seems that 9 plus might cause a problem,,, the rest of your code is clean.. try ld 96 enl serv for that route.. stat serv... you may need service msgs for setup.. and you may need vce instead of vod... and i have had one refuse to est unitll i added the rls of the far end..

remember that everytime you make a change.. dis the msdl and re-enable it fdl...

john poole
bellsouth business
columbia,sc

 

[tsinc]

Thanks John !! ... I'll try the service msgs idea ... and will change to vce rather than vod ... for far end rls id, I thought that only applied to rls of another Meridian system ... I'm connecting to a Bell DMS100 ... so I'm not sure of the release ... I'll check the ntp's and see if there is a dms100 default to put in there ...

thanks again ... and enjoy your vacation !! ...