PAETEC ISDN PRI cannot bring up

[uzumaki]

Hi Guys,

We have a remote G450 in Bethesda, Maryland - and the main server is here in singapore. Its my first time to setup an ISDN PRI - T1 config. I just want to verify if my configurations for my trunk is correct or not.

change ds1 002v2 Page 1 of 2
DS1 CIRCUIT PACK

Location: 002V2 Name: ISDN
Bit Rate: 1.544 Line Coding: b8zs
Line Compensation: 1 Framing Mode: esf
Signaling Mode: isdn-pri
Connect: network
TN-C7 Long Timers? n Country Protocol: 1
Interworking Message: PROGress Protocol Version: b
Interface Companding: mulaw CRC? n
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz

T303 Timer(sec): 4


Slip Detection? y Near-end CSU Type: other

Echo Cancellation? y Block Progress Indicator? n
EC Direction: inward
EC Configuration: 8

change ds1 002v2 Page 2 of 2
DS1 CIRCUIT PACK

ESF DATA LINK OPTIONS

Network Management Protocol: tabs
Send ANSI-T1.403 One-Second Performance Reports? n
Far-end CSU Address: b


change signaling-group 40 Page 1 of 5
SIGNALING GROUP

Group Number: 40 Group Type: isdn-pri
Associated Signaling? y Max number of NCA TSC: 2
Primary D-Channel: 002V224 Max number of CA TSC: 2
Trunk Group for NCA TSC:
Trunk Group for Channel Selection: 40 X-Mobility/Wireless Type: NONE
TSC Supplementary Service Protocol: a


change trunk-group 40 Page 2 of 21
Group Type: isdn

TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: b Digit Handling (in/out): enbloc/enbloc


Our telco is PAETEC... neverheard of it before so i was wondering if someone can help me out on this.

In reference to this thread: thread690-1540190, i hope AvayaTier3 will answer my question

 

[Midstream]

Test the DS-1 board and paste the results. We'll be able to tell you a lot after seeing those results.

As an aside, change the CSU type to integrated on the DS-1 board form.

 

[DAVIDPAYNE]

Have you been on a call with a PAETEC provision group tech?
Have you checked your config with them.

What errors are you seeing?
I also agree with rockspop, change that setting.

But the bottom line is that the carrier, and only the carrier will know if you are programmed correctly for the equipment the circuit is provision through.

 

[mikeydidit]

Check and make sure the protocol you are using. It must match the vendors. Also on the ds1 you have it as B and on the signaling group you have it as A.

Supplementary Service Protocol: a

When is the last time you helped someone, just because you were able to?

For the best response to a question, read faq690-6594

 

[kjrnec]

Have you spoken to the provisioning tech with PAETEC on how the trunk should be setup? Until you do that your not going to know if everything is setup correctly or not.

 

[uzumaki]

Guys apologies and thanks for the support, right now we are having errors on loss of signal, test 138. But most likely i just want to know if my DS1 board parameter is correct?

 

[Midstream]

It might work the way you have it, but we won't know until the D-Channel is turned up, the B-Channels are turned up and you've tested it. If you have the Paetec cut sheet parameters with signaling, coding and ISDN protocol, post them.

Protocol "a" is AT&T Custom, protocol "b" is NI-2. You'll want to make sure that you have those set to match your provider.

Have you instructed Paetec to turn up the D and B channels yet? That may be the cause of loss of signal.

 

[DAVIDPAYNE]

They could also still have it looped for testing.

 

[uzumaki]

Guys these are the results of the test board:

test board 002v5 Page 1

TEST RESULTS

Port Mtce Name Alt. Name Test No. Result Error Code

002V5 MG-DS1 138 PASS
002V5 MG-DS1 139 PASS
002V5 MG-DS1 140 PASS
002V5 MG-DS1 141 PASS
002V5 MG-DS1 142 PASS
002V5 MG-DS1 143 PASS
002V5 MG-DS1 144 PASS
002V5 MG-DS1 145 PASS
002V5 MG-DS1 146 PASS
002V5 MG-DS1 1227 ABORT 1412
002V501 ISDN-TRK 0042/001 36 PASS
002V501 ISDN-TRK 0042/001 255 PASS
002V501 ISDN-TRK 0042/001 256 PASS
002V501 ISDN-TRK 0042/001 257 PASS
002V502 ISDN-TRK 0042/002 36 PASS


All channels are pass. Its just the DS1 board. And Also im getting this error:

list trace tac *27 Page 1

LIST TRACE

time data

13:03:23 dial 900113016522000# route:ARS
13:03:23 term trunk-group 42 cid 0x50f
13:03:23 dial 900113016522000# route:ARS
13:03:23 route-pattern 7 preference 1 cid 0x50f
13:03:23 seize trunk-group 42 member 18 cid 0x50f
13:03:23 Setup digits 3016522000
13:03:23 Calling Number & Name 3012023000 NxGen Test 3
13:03:23 G729A ssff ps:20
rgn:1 [10.0.66.50]:2924
rgn:4 [10.0.7.198]:2054
13:03:23 denial event 1198: ISDN req fac no subscribe D1=0x52 D2=0x232
13:03:23 idle trunk-group 42 member 18 cid 0x50f
13:03:27 idle station 5002 cid 0x50f


Inbound can receive calls but, we cannot perform outbound calling. Can anyone share some configuration on this? Can someone post their route pattern config?

 

[BHodgins]

On outbound calls are you sending just 10 digits? You may need to check your AAR/ARS and routing patterns.

 

[AvayaTier3]

DNY_ISDN_RFNS (1198) requested facility not subscribed

whatever digits you are sending to your provider, they have no way to deal with them.

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

36 years Bell, AT&T, Lucent, Avaya
Tier 3 for 26 years and counting

http://bshtele.com