Outbound CLID Trouble 1

[RahjiSupreme]

I can not get my outbound CLID to work. BellSouth complex translations techs say their protocol analyzer does not see ANY originating digits coming from my switch. BellSouth said that somewhere in my switch tables, I must be set to not pass the information to the “public” network. I’ve researched your past forums and found a lot of configuration information. Most of which matched what I had already had configured. The funny thing is, when I ENL MSGO on my dchannel, I can see the correct CLID. Can someone help me out?

ENL MSGO 0 .
DCH 0 OMSG SETUP REF 00000022 CH 3 10 TOD 14:05:38
CALLING #:3425742 NUM PLAN: E164/SUBSCRIBER (NXX)
CALLED #:3163707 NUM PLAN: E164/SUBSCRIBER (NXX)

DCH 0 OMSG CONN ACK REF 00000022 CH 3 10 TOD 14:05:46

DCH 0 OMSG RELEASE REF 00000022 CH 3 10 TOD 14:05:52
_______________________________________________________
PRT TYPE: CLID CUST 0 SIZE 256
RNGE INTL

ENTRY 0
HNTN 864
ESA_HLCL
ESA_INHN NO
ESA_APDN YES
HLCL 3425600
DIDN NO
HLOC
LSC
CLASS_FMT DN

ENTRY 1
HNTN 864
ESA_HLCL
ESA_INHN NO
ESA_APDN YES
HLCL 342
DIDN YES
HLOC
LSC
CLASS_FMT DN

ENTRY 2
HNTN 864
ESA_HLCL
ESA_INHN NO
ESA_APDN YES
HLCL 253
DIDN YES
HLOC
LSC
CLASS_FMT DN

ENTRY 3
HNTN 864
ESA_HLCL
ESA_INHN NO
ESA_APDN YES
HLCL 573
DIDN YES
HLOC
LSC
CLASS_FMT DN

ENTRY 4
HNTN 864
ESA_HLCL
ESA_INHN NO
ESA_APDN YES
HLCL 594
DIDN YES
HLOC
LSC
___________________________________________________________
REQ PRT TYPE ADAN DCH
ADAN PRIM DCH 0
BDCH 1
CTYP MSDL
DNUM 6
PORT 1
DES DCHPRI2
USR PRI
DCHL 2
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100
SIDE USR
CNEG 1
RLS ID 36
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7
ADAN BKUP DCH 1
PDCH 0
CTYP MSDL
DNUM 6
PORT 2
BCHL 3
RCVP NO
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100
SIDE USR
CNEG 1
RLS ID 36
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7
___________________________________________________________________
REQ: PRT TYPE: RDB CUST 0 ROUT 0
TYPE RDB
CUST 00
ROUT 0
DES BELLSOUTH 8900
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 8900
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0 *
NDNO 0
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 3968
NRD 10112
DDL 70
ODT 3840
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096



PAGE 002

IENB 5
VSS 0
VGD 6
DRNG NO
CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA NO
OAN YES
OPD YES
CDRX NO
NATL YES
VRAT NO
MUS YES
MRT 10
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS YES
ALRM YES
ART 0
SGRP 0
AACR NO


(Sorry so long, I'm new to this)

 

[dlesap]

If you send that CLID, the other side must receie it if it's a direct link.
If any other provider is carrying your call and modify the CLID or deleted it, you have to check with that parts

 

[RahjiSupreme]

Thanks, I just wanted to make sure I wasn't missing something. The carrier is BellSouth and they say that they don't see any digits. They did say that it could be because I'm not sending 10 digits. Do you know how I send the NPA also? Currently my MSGO and call traces show 7 digits.

 

[dlesap]

Sorry we don't use NPA in Europa.
Anyway if you don't send 10 digits but only 4 the provider must be able to see it