Outbound Call Routing

[sliderplot]

Hello,

New to the Nortel switch and fighting my way thru any issues, need some help with CS1000 server on figuring out how outbound and inbound calls are routed to PRI's for office. I have two voice circuits loop 50 which carries all DID inbound calls and loop 51 which looks like is only used for outbound calls. Need to find routing table that determines which loop is used and if one loop is down will all calls route to remaining loop for outbound and inbound calls.

Looking for command/s that I need to use to verify the call routing for this CS1000 unit.

Thanks for the help.

 

[LittleMaster]

HI SLIDERPLOT.... i don't have high level of speciality but i want to share some here..
____________________________
you have to work in like this
STEP 1 : TAKE A STAT OF ALL CHANNELS OF LOOP :
LD 60
.STAT 50
it will display all channels of that PRI.
then
.stat 51
Note : here you can check the type of trunks/channels ...Like DID (for inbound) or COT/TIE(outbound)
________________________________
step 2: here you will take a print of channel/TN of loop 50 or 51.
LD 20
REQ PRT
TYPE TN
CUST 0
TN 50 1 **********(THIS IS THE FIRST CHANNEL OF lOOP 50)
here you have to watch for
*option TYPE DID or COT or Tie etc
*option RTMB x y (x route and y is member of that)
____________________________
step 3:
LD 21
REQ LTM
CUST 0
ROUT X (give the route number you found above)
*here you will find a list of all trunk members of that route.

you can also take a print of that route in here..
LD 21
REQ PRT
TYPE RDB
CUST 0
ROUT X
_______________________________

YOU MUST HAVE OUTBOUND AND INBOUND CHANNELS IN BOTH THE LOOPS ,,,SO THAT IF ONE LOOP BECOMES DOWN THE CALLS WILL FOLLOW OTHER LOOP.

 

[KCFLHRC]

All of the call routing you are referring to is done in LD 86 in the RLI's. There can be multiple entries in each RLI. It will be very overwhelming if you have not done this before.

 

[sliderplot]

Thanks for the greet information above, I have completed task but have one final question about routing.

I can see from the results below that route '0' RTMB routes calls to loop 50 member 1 and route 51 RTMB routes to loop 51 member 24 which is fine. But I would like to disable loop 51 and send all calls out loop 50 will calls that are sent using RTMB 0 24 then find loop 50 and be routed out on PRI?

Big thanks again.



PRI* TRK LOOP 50 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
TRACKING
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE DID VCE * CH 02 - IDLE DID VCE *
CH 03 - IDLE DID VCE * CH 04 - IDLE DID VCE *
CH 05 - IDLE DID VCE * CH 06 - IDLE DID VCE *
CH 07 - IDLE DID VCE * CH 08 - IDLE DID VCE *
CH 09 - IDLE DID VCE * CH 10 - IDLE DID VCE *
CH 11 - IDLE DID VCE * CH 12 - IDLE DID VCE *
CH 13 - IDLE DID VCE * CH 14 - IDLE DID VCE *
CH 15 - IDLE DID VCE * CH 16 - IDLE DID VCE *
CH 17 - IDLE DID VCE * CH 18 - IDLE DID VCE *
CH 19 - IDLE DID VCE * CH 20 - IDLE DID VCE *
CH 21 - IDLE DID VCE * CH 22 - IDLE DID VCE *
CH 23 - IDLE DID VCE * CH 24 - DCH 50
.stat 51

PRI* TRK LOOP 51 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE DID VCE * CH 02 - IDLE DID VCE *
CH 03 - IDLE DID VCE * CH 04 - IDLE DID VCE *
CH 05 - IDLE DID VCE * CH 06 - IDLE DID VCE *
CH 07 - IDLE DID VCE * CH 08 - IDLE DID VCE *
CH 09 - IDLE DID VCE * CH 10 - IDLE DID VCE *
CH 11 - IDLE DID VCE * CH 12 - IDLE DID VCE *
CH 13 - IDLE DID VCE * CH 14 - IDLE DID VCE *
CH 15 - IDLE DID VCE * CH 16 - IDLE DID VCE *
CH 17 - IDLE DID VCE * CH 18 - IDLE DID VCE *
CH 19 - IDLE DID VCE * CH 20 - IDLE DID VCE *
CH 21 - IDLE DID VCE * CH 22 - IDLE DID VCE *
CH 23 - IDLE DID VCE * CH 24 - DCH 51
.***
OVL000
>ld 20

PT0000
REQ: prt
TYPE: did
TN 50 1
DATE
PAGE

DES PRI1
TN 050 01 VIRTUAL
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 0 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 19 NOV 2009


NACT
REQ: prt
TYPE: did
TN 51 1
DATE
PAGE

DES PRI1
TN 051 01 VIRTUAL
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 0 24
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 18 NOV 2009


NACT
REQ: ***
OVL000
>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 0

TYPE RDB
CUST 00
ROUT 0
DES DID
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA NO
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
DSEL VCE
PTYP DCO
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB NO
STEP
ACOD 8000
TCPP NO
PII NO
AUXP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096


PAGE 002


IENB 5
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
EQAR NO
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO


REQ: ltm
CUST 0
ROUT 0

TYPE TLST
TKTP DID
ROUT 0
DES DID
TN 050 01 MBER 1 PRI1
TN 050 02 MBER 2 PRI1
TN 050 03 MBER 3 PRI1
TN 050 04 MBER 4 PRI1
TN 050 05 MBER 5 PRI1
TN 050 06 MBER 6 PRI1
TN 050 07 MBER 7 PRI1
TN 050 08 MBER 8 PRI1
TN 050 09 MBER 9 PRI1
TN 050 10 MBER 10 PRI1
TN 050 11 MBER 11 PRI1
TN 050 12 MBER 12 PRI1
TN 050 13 MBER 13 PRI1
TN 050 14 MBER 14 PRI1
TN 050 15 MBER 15 PRI1
TN 050 16 MBER 16 PRI1
TN 050 17 MBER 17 PRI1
TN 050 18 MBER 18 PRI1
TN 050 19 MBER 19 PRI1
TN 050 20 MBER 20 PRI1
TN 050 21 MBER 21 PRI1
TN 050 22 MBER 22 PRI1
TN 050 23 MBER 23 PRI1
TN 051 01 MBER 24 PRI1
TN 051 02 MBER 25 PRI1
TN 051 03 MBER 26 PRI1
TN 051 04 MBER 27 PRI1
TN 051 05 MBER 28 PRI1
TN 051 06 MBER 29 PRI1
TN 051 07 MBER 30 PRI1
TN 051 08 MBER 31 PRI1
TN 051 09 MBER 32 PRI1
TN 051 10 MBER 33 PRI1
TN 051 11 MBER 34 PRI1
TN 051 12 MBER 35 PRI1
TN 051 13 MBER 36 PRI1
TN 051 14 MBER 37 PRI1
TN 051 15 MBER 38 PRI1
TN 051 16 MBER 39 PRI1
TN 051 17 MBER 40 PRI1
TN 051 18 MBER 41 PRI1
TN 051 19 MBER 42 PRI1
TN 051 20 MBER 43 PRI1
TN 051 21 MBER 44 PRI1
TN 051 22 MBER 45 PRI1
TN 051 23 MBER 46 PRI1

 

[KCFLHRC]

Once again, the routing is done in ld 86 in the RLI. However you can disable loop 51 and the associated d-channel and it will be fine. The only thing you are showing in your print outs is the route and associated trunks. Not the actual routing for AC1 for a particular NPA, NXX or SPN.