Option 11C Mini (NTDK91) AMLM024 04 1

[MatthewOK]

New guy here...
I have acquired a 11C mini and recovered the passwords for the system (25.08). I do not have the expansion cabinet that housed the Meridian Mail and I would like to remove the references to it hoping also clears the "AMLM024 04" message I am receiving. I'm new to the system but am enjoying learning it little bit-by-bit.

What loads should I visit to remove the meridian mail and hopefully fix the error? Thanks in advance.

 

[Firebird Scrambler]

It's been a while but I think LD48 is where you disable AML 8

LD 17 under ADAN is where you remove the AML.
Best to go to LD 22 first and print off the CFN data.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =

http://somertel.net

linkedin

 

[MatthewOK]

Thanks!
I see it listed in cabinet 1, which I do not have, and it appears to be configured as TTY 04. I could use a couple of hints to the next steps.

ADAN TTY 4
TTY_TYPE SDI
CAB 01
DES
FLOW NO
USER CTY

 

[Firebird Scrambler]

No, it's not TTY 4.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =

http://somertel.net

linkedin

 

[Firebird Scrambler]

Just print and post the CFN data in LD 22

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =

http://somertel.net

linkedin

 

[MatthewOK]

ADAN HIST
SIZE 50000
USER MTC SCH BUG
ADAN TRF
SIZE 50000
ADAN TTY 0
TTY_TYPE SDI
CAB 00
CARD 00
PORT 0
DES modem
FLOW NO
USER MTC SCH BUG
TTYLOG 10000
BANR NO
ADAN TTY 1
TTY_TYPE SDI
CAB 00
CARD 00
PORT 1
DES Alarm
BPS 9600
BITL 8
STOP 1
PARY NONE
FLOW NO
USER MTC SCH BUG
TTYLOG 10000
BANR NO
ADAN TTY 2
TTY_TYPE SDI
CAB 00
CARD 00
PORT 2
DES pollsafe
BPS 9600
BITL 8
STOP 1
PARY NONE
FLOW NO
USER CTY
ADAN TTY 4
TTY_TYPE SDI
CAB 01
DES culver
FLOW NO
USER CTY
ADAN TTY 6
TTY_TYPE PTY
PORT 1
DES trf
FLOW NO
USER TRF
TTYLOG 0
ADAN DCH 11
CTYP TMDI
CARD 01
PORT 1
DES MCI_PRI
USR PRI



PAGE 001

DCHL 1
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
ADAN DCH 30
CTYP TMDI
CARD 02
PORT 1
DES qsig_cisco
USR PRI
DCHL 2
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID 1
RCAP COLP NDI CCBI CCNI PRI DV3I CTI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
PARM
LPIB 300
HPIB 96
500B 500
AMLM024 04

NCR 1500
MGCR NULL
CFWS YES



PAGE 002

PCML MU
ALRM YES
ERRM ERR BUG AUD
DTRB 100
TMRK 128
FCDR OLD
PCDR NO
TPO NO
TSO NO
CLID YES
DUR5 NO
MLDN YES
MARP YES
FRPT NEFR
DCUS NULL
MSCL 2500
PMSI
MANU PMS1
PMCR 20
PORT NONE
NDIS 20
OCAC NO
MTRO MR
SBA_ADM_INS 001
SBA_USER 010
BCAP SPEECH
NORTEL_BRAND NO
CEQU
MPED 8D
SUPL 000 004 008 012
016 032 036 040
044 048 064 068
072 V100 P112
XCT 000
CONF 029 030 031 062
094 095

DLOP NUM DCH FRM LCMT YALM T1TE TRSH
PRI 001 23 ESF B8S FDL 0 00
002 23 ESF B8S FDL 0 00
MISP
OVLY
SID 3365
BKGD 044
PBXH 01
TODR 22
DROL 034 044 060
MULTI_USER ON
ATRN
CODE 0
SOLR 12
ROLR +45.00
AOLR +45.00
TOLR -45.00
AGCD NO
VOLR NO
HRLR +42.00
HTLR -44.00

 

[Firebird Scrambler]

Thanks for the printout. You don't have any Mail configured. Looking at the error again and realising that you have a Option 11c Mini system reminds me that the error AMLM024 04 probably refers to slot 4 in the main cabinet.

Slot 4 was a 48 port digital extension card that only ever existed for the 11c mini chassis unlike the later CS1000 ones that took a standard card such as a 16 port digital card in slot 4.

If slot 4 has not got the 48 DLC in it, then it must be left spare and unused.

Go into LD 20 and use STAT 4, STAT 5, STAT 6 etc.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =

http://somertel.net

linkedin

 

[MatthewOK]

Thank you!

Yes, I have a mini and also the 48 port DLC card, it is seated but in alarm. Poking around last night it appears those three slots are not configured erectly. I have ordered two TDMI cards to fill 1& 2.

Again, thanks for the help, this is quite the steep learning curve for a home project, but it has been enjoyable.

TMDI 1 <Unavailable>
TMDI 2 <Unavailable>
CONF 29 <Unavailable>
CONF 30 <Unavailable>
CONF 31 <Unavailable>
CONF 62 <Unavailable>
XCT-TDS/MF 63 <Unavailable>
CONF 94 <Unavailable>
CONF 95 <Unavailable>
DTR 0 <Unavailable>
500 3 NT8D09BB 02 NNTMENC5Y4A0 0000
500 4
DLC 5
DLC 6
EXUT 7 <Unavailable>
DLC 8 <Unavailable>
500 9 <Unavailable>
DLC 10 <Unavailable>

 

[Firebird Scrambler]

As it's a home project, I'd delete all data for slots 3 onwards. Slot 1 and 2 is programmed for a digital TMDI card. Slots 3 onwards could also be extension cards.

If you aren't using the expansion cabinet, then TTY 4 can be deleted.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =

http://somertel.net

linkedin

 

[MatthewOK]

Thanks. I was able to find it and out-it. Problem solved.