Opt81 to Shoretel 2

[abntelecom]

I'm programming a p2p pri to connect a Shoretel and an Opt81c. I would like to send DID calls across the T from Opt81c. Outbound calls also from Shoretel using the Opt81c trunks.

I programmed my dch with NI2 protocol and built my trunks as DID. Programmed CDP to route calls across the T. I can dial 4 digit dialing on both switches. If I dial the number from outside, it would ring the reception.

Can anyone please let me know the correct way of programming a P2P? Please post DCH, RDB, TN and so on.

Thank you very much.

 

[fritzthecat]

Hello
seams that plug in 27 is not enabled,
Plugin 27 description:

DID to DID call intercepts to attn

BV49770

Go into pdt and do a plp 27 then you see if it is enabled or not, if not, do a ple 27 and then give them a trial.

This plugin is available since Rel. 25.40

regards and good luck

Fritz

 

[johnpoole]

what's the ncos of your inbound and the ncos of the tie's.. they need to match... are you using qsig? that would be my 1st choice.. usually when that happens the ncos of the inbound is lower then the ncos of the outbound.. since the dsc does not have an ncos the switch uses the ncos of the inbound trunk, if the ncos of the tie trunk is higher or if the two have the same targ it's a block.. make sure you x1 the targ in at least the internal.. i can post a tie but it's qsig.. my 81 to 11 tie is not pri so that will not help

john poole
bellsouth business
columbia,sc

 

[abntelecom]

Ncos is 7 for both inbound and outbound. Someone told me to set it up as TIE instead of DID to past did calls across the T.

 

[johnpoole]

it does not usually matter, did and tie are so much alike but try it.. do the targs match? and is it marked rcls int?

that tells the switch that it is an internal route

john poole
bellsouth business
columbia,sc

 

[abntelecom]

TARG don't match. I'll change the rcls to INT.

 

[abntelecom]

Changed it to int but still got the reception.

 

[abntelecom]

>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 19

TYPE RDB
CUST 00
ROUT 19
DES SHORETEL_HQ
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS INT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 7
SBN NO
PNI 00001
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 430009
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096


PAGE 002


IENB 5
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS YES
MRT 30
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

REQ: ***
OVL000
>ld 22
PT2000

REQ prt
TYPE adan dch 14

ADAN DCH 14
CTYP MSDL
GRP 1
DNUM 8
PORT 0
DES Shoretel_HQ
USR PRI
DCHL 19
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT2
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
RCAP NCT COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO

REQ ***
OVL000
>ld 20

PT0000
REQ: prt
TYPE: tnb
TN 19 1
DATE
PAGE
DES

DES SHORETEL_HQ
TN 019 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 7
RTMB 19 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 19 OCT 2006

 

[wilcom]

I am currently having this same problem: internal calls go over the tie no problem; external calls routed to the attendant.

Were you able to resolve the issue? If so, what was your solution?

 

[VonZipper]

We tried and tried for along time to get a setup like this to work, and after about 20 hours of testing, we finally went to QSIG signaling. 20 minutes to program, and has ran great ever since.

 

[wilcom]

Thanks VonZipper.

Same experience. Everything routes fine since configuring with the ISGF signaling to accommodate a TIE route. Luckily, the several hours spent screwing around with restictions levels were billable T&M!