Obtaining ADSL speed of interface

[f2b]

We currently have an 8Mb ADSL connected to our Cisco 2800. Sometimes the ADSL is really even at weekends when vet few people are in.
Is there a way to check the current upstread/downstream speed is? Would be very useful.

Thanks
Ski

 

[ADB100]

I assume you have a WIC-1ADSL interface and the ISP doesn't provide Ethernet? If so you can type 'show dsl interface atm 0' where '0' is the slot the WIC-1ADSL is installed in.
I have an 837 fixed-config ADSL router and the output from mine is:

cisco-837#show dsl interface aTM 0
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'TSTC'
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x00 0xB5
Capacity Used: 30% 38%
Noise Margin: 25.0 dB 24.0 dB
Output Power: 20.0 dBm 10.5 dBm
Attenuation: 33.5 dB 18.5 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 1281 (2 spurious)
Activations: 1
Init FW: embedded
Operartion FW: embedded
SW Version: 3.9.220
FW Version: 0x1A04

Interleave Fast Interleave Fast
Speed (kbps): 0 2272 0 288
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 14 0 0
Header Errors: 0 6 0 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
00: 0 0 0 0 0 0 0 2 0 3 3 4 5 5 6 5
10: 5 5 5 5 5 5 5 5 5 4 4 4 3 2 0 0
20: 0 0 0 0 0 0 2 2 3 3 4 4 5 5 5 5
30: 5 5 5 5 6 6 6 6 6 6 6 6 6 6 5 5
40: 0 6 6 2 6 6 6 6 5 5 5 5 5 5 5 5
50: 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
60: 5 5 5 5 5 5 5 5 5 5 5 5 5 5 4 4
70: 5 5 4 4 4 4 4 4 4 4 4 4 4 4 4 4
80: 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
90: 4 4 3 3 4 3 3 3 4 4 4 4 3 3 3 3
A0: 3 2 3 2 2 2 2 2 2 2 3 2 3 3 3 3
B0: 3 3 2 2 2 2 2 2 2 2 2 2 2 2 2 2
C0: 2 2 2 2 2 2 2 2 2 2 2 2 2 0 0 0
D0: 0 0 0 0 2 2 2 2 2 2 2 2 2 0 2 0
E0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Training log buffer capability is not enabled yet.
cisco-837#

The upstream/downstream is on the Speed (kbps) line. My service is 2Mbps (2272Kbps downstream & 288Kbps upstream).

HTH

Andy

 

[f2b]

Yes I should have mentioned it's a WIC-ADSL and the command shows the speed etc.

Brillient. Thank you.

Ski

 

[sahajesh]

Hiya,

Got a 1721 router with WIC ADSL and a few questions:

1) What does 'activations' refer to?

2) What is the 'training log buffer capability' and how is this enabled?

Thanks,

Sahajesh.