NTRB21 TMDI Card Questions

[SherWat]

I have some questions about using an NTRB21 TMDI card please.

CS1000 at 7.6
In an MG1010 Cabinet

1. Can I use slot 5 for the NTRB21 TMDI card?
2. Would this card allow a TIE connection to an AudioCodes Mediant 1000 gateway?

I created a new digital loop in LD 17 as loop 25

DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH MG_CARD
PRI 021 24 ESF NO B8S FDL - 00 000 0 02
023 24 ESF NO B8S FDL - 00 016 0 07
025 24 ESF YES B8S FDL 0 00 000 0 05
​

I created a new RDB in LD 16

TYPE RDB
CUST 00
ROUT 70
DES SOLACOMTIE
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL VCE
PTYP DTT
CNDP UKWN
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 5800
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3

IENB 5
TFD 0
VSS 0
VGD 6
SST 5 0
NEDC ETH
FEDC ETH
CPDC NO
DLTN YES
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO


PAGE 002

VRAT NO
MUS NO
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
ACF NO
AACR NO
​

I created new trunks in LD 14 - one of which is shown below:

DES TIE
TN 025 19 VIRTUAL
TYPE TIE
CUST 0
TRK DTI
PDCA 1
PCML MU
NCOS 7
RTMB 70 19
A/B BIT SIGNALING
TGAR 1
SIGL EM4
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS CTD DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
FCAR NO
AACR NO
DATE 19 APR 2022
​

The 25 pair Amphenol cable from the back of the MG1010 cabinet is terminating on a 24 pair patch panel. From there I believe I need to use ports 23 and 24 on the patch panel to connect to the AudioCodes Mediant gateway.

I tried to enable the TMDI in LD96 but received an MSDL028 error

>ld 96
DCH000
.stat tmdi
TMDI 000 0 5 MAN DSBL
.enl tmdi 0 0 5

MSDL028

.****
>
OVL000
>err msdl028
>

MSDL0028
Cannot enable the card because it is not present in the system.
If the card in question is believed to be present, check if the switch
settings on the card agree with the device number entered in this
command.
Severity: Minor

​

I guess if I can't use slot 5 that is why I can't enable it?

Thanks.

 

[bignose21]

You can have it in slot 5, from your description above I didn't see the bit where you said "I created the DCH in LD 17", so I guess in LD 96 if you STAT TMDI there isn't one?

 

[SherWat]

Yes, creating a DCH would certainly help! I created one:

ADAN DCH 18
CTYP TMDI
MG_CARD 000 0 05
PORT 1
DES SOLACOMTIE
USR PRI
DCHL 25
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC SL1
SIDE USR
CNEG 1
RLS ID 35
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7
​

When I try to enable the DCH in LD96 I receive
DCH0042
MSDL card has to be in operational state

When I try to ENL TMDI in LD96, it comes back with MSDL028 which tells me the card is not present in the system. I have reseated the card. Are there any DIP switches on the card I should check?

UPDATE- just reseated it again and it now came up

 

[bignose21]

good stuff