Nortel Suc 3.0 - Cisco CCM integration 1

[rpneal44]

Has anyone tried yet to connect a PRI from an Option 11C to a Cisco Call Mgr Yet? I spent 5 hours last night trying to find a DCH protocol that the two would find compatible and was unsuccessful to say the least. (Crisco?...I know, I know...long story) The cisco vemdor dude was not much help. Any help any one here can provide would be greatly appreciated.

 

[hectorbest]

Hi,

try this we have problems but its resolve with this programation


CHANNEL D

ADAN DCH 37
CTYP MSDL
GRP 2
DNUM 11
PORT 1
DES XXXXXXXXXXX
USR PRI
DCHL 83
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
QCHID YES
RCAP COLP
MBGA NO
OVLR YES
DIDD 0
OVLS YES
OVLT 0
T310 120
T200 3
T203 10
N200 3
N201 260
K 7


TRUNKS 1-30


DES XXXXXXXX
TN 083 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML A
NCOS 0
RTMB 36 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD XREP BARD
P10 VNL
TKID
DATE 3 AUG 2007



ROUTE



ROUT 36

TYPE RDB
CUST 00
ROUT 36
DES
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00001
NCNA NO
NCRD NO
CTYP CDP
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 05989
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
MFC NO
ICIS YES
OGIS YES
PTUT 0
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896


PAGE 002

SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG NO
CDR YES
INC YES
LAST NO
TTA NO
QREC NO
OAL YES
AIA YES
OAN YES
OPD NO
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
FRL 0 7
FRL 1 7
FRL 2 7
FRL 3 7
FRL 4 7
FRL 5 7
FRL 6 7
FRL 7 7
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 1
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 05989 36
SGRP 0
CCBA NO
AACR NO



good luck!!!

 

[rpneal44]

Do you know if there might be any differneces in programming that might be present between an 81c and an 11c?

 

[johnpoole]

the software side will be the same.. if you have qsig packages, that is the way i would suggest.. here is my config between my rls 3, 81c and out ccm..

http://www.tek-tips.com/viewthread.cfm?qid=1017219

john poole
bellsouth business
columbia,sc

 

[mabsar]

Since I dont have QSIGGF package thats why I have configured IFC=S100 for my 81c Rls 3 system and it is working fine.

 

[rpneal44]

Do you know if this config will allow passing the name displays associated with the estensions? Is this an RCAP setting? Below is my current DCH cinfig that passes calls w/ ext nos.:



ADAN DCH 5
CTYP MSDL
CARD 08
PORT 1
DES CCMgr
USR PRI
DCHL 8
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP NDI PRI DV3I CTI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR YES
DIDD 0
OVLS YES
OVLT 0
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

 

[rpneal44]

Below is the final DCH config that passes ext no as well as name display. Also included (below that) is the Cisco side's set-up. This is a long, hard fought battle, but it does work, and works well. It even passes to the rest of the Nortel network of ours. Hope this saves someone else these same headaches.


ADAN DCH 5
CTYP MSDL
CARD 08
PORT 1
DES CCMgr
USR PRI
DCHL 8
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ESGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP NDI PRI DV3I CTI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7


Here's the Cisco set-up. The (ALL CAPPS) are the techs notes.

voice service voip
qsig decode (THIS IS WHAT ALLOWED US TO GET NAME FROM NORTEL)
!
!
!
!
!
!
!
!

!
!
controller T1 0/0/0
framing esf
clock source internal
linecode b8zs
pri-group timeslots 1-24
description Mainstream Nortel Option 11 !
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn protocol-emulate network
isdn incoming-voice voice
isdn supp-service name calling (NEEDED FOR NAME FROM CISCO TO NORTEL) isdn outgoing ie facility (NEEDED FOR NAME FROM CISCO TO NORTEL) isdn outgoing ie extended-facility isdn outgoing ie network-facility isdn outgoing display-ie trunk-group PBX 2 !
voice-port 0/0/0:23
input gain -2
output attenuation 2
echo-cancel erl worst-case 3

 

[srtelengine]

rpneal44,
Thanks for the post. If I can get the cisco guys tomorrow we will try that config. We have tried quite a few things but no success. So if a call goes thru CallPilot or transfered from a Nortel phone it will pass the CLID of the person call not the CP port DN or set DN?

Dwayne

 

[rpneal44]

Suncomminc - I would think that the caller's ext no would pass since CP would be doing a blind xfer. If a person was xfr the call then I would think that ext no would pass. We are running opt 11c w/ succ 3.0 and rel 12 MerMail, so can't speak for CP specifically but I don't think it would be treated any differently. One thing I did note was that when a call passes THRU the Opt 11 to the CCM (from a networked 61c) the caller ID is not passed until the call is answered. I think it has to do with the different RCAP settings between the 2 PRIs in the Opt 11. Same thing happens in both directions.

I feel pretty confident that this set-up will work for you. If it doesn't, post it, and we'll all see what we can work out.

 

[srtelengine]

rpneal44,
One of the biggest reasons I really want to see this work is because Cisco say that it cannot be done.

Dwayne

 

[srtelengine]

Well guys here is the Nortel side to pass CLID to Cisco Call Manager 5.1
ADAN DCH 56
CTYP MSDL
GRP 1
DNUM 4
PORT 0
DES CISCO
USR PRI
DCHL 56
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
PR_TRIGS DIV 2 3
CNG 2 3
CTR2 2 3
PR_RTN NO
MBGA NO
OVLR YES
DIDD 0
OVLS YES
OVLT 0
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

ROUT 88
DES CISCO
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00001
NCNA NO
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 9752
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

DES CISCO
TN 056 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 6
RTMB 88 1
B-CHANNEL SIGNALING
TGAR 0
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD HKD
P10 VNL
TKID
AACR NO

We finally had the chance to do a full test today, even going thru CallPilot or a transfer from a set it passes the proper CLID.

I would like to thank everyone for the help that was provided. That is what makes this forum great.

Dwayne