Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Nortel SR1001 password recovery procedure.

Status
Not open for further replies.

lock1

Technical User
Nov 13, 2007
5
US
Nortel password recovery procedure for SR1001 router?
 
Solution Detail


How to recover a lost password

--------------------------------------------------------------------------------

Problem Description
If the router password is lost, how can it be recovered?
Problem Resolution



As indicated in solution 4099314, have the system setting configured at the time of provisioning as follows:

SR/configure > no system reset-to-factory
System will delete all user accounts the next time boot command 'X' is executed

By having this system setting in place, the password can be recovered without having the router set to factory-defaults and thus losing the entire configuration which would cause a longer-than-needed outage.

Assuming the system setting is configured indicated in solution 4099314, the password can be erased as follows:

1. Establish a console connection to the router and then reboot the router.


SR > reboot

WARNING : Configuration changes not yet saved!


FOLLOWING PARAMETERS WILL BE USED TO BOOT UP

BOARD : NCM
HOST IP ADDRESS: 10.10.1.10
BOOTING FROM : FLASH
BOOT FILE : /cf0/H1000.Z
BOOT MODE : FAST

REBOOT: ARE YOU SURE (Y/N) ? y



2. Press <Enter> until you come to the boot prompt and then issue the "X" command:



[VxWorks Boot]: X
Are you sure you want to reset username/password to factory default? y
moving zeros, length 52, to offset 0x18ae2 in NVRAM
Username/password have been reset



3. Reboot the router issuing the "@" command:



[VxWorks Boot]: @



4. When the router completes the boot cycle, the router prompts you to enter a new Root User name:



Attaching /flash1, please wait...
Completed basic flash initialization
Initializing Flash...
done
Initializing USB subsystem
No Mass Storage device plugged. You can plug it in now.

02/10/2009-13:07:53 : emergency : ALARMS
Power 1 failed
attached the link-restoral timer from Config-Mgr task
attached the display counter timer from Config-Mgr task
started diff-Delay-timer in context of L2-task
Attaching network interface lnPci1... done.
Enter new Root User name to be configured: admin

admin logged in on TUE FEB 10 13:08:21 2009 from CONSOLE

Firmware revision: r9.3.3 - Nov 8 2008, 23:52:07
Model: SR 3120

Nortel
600 Technology Park Drive, Billerica, MA. 01821
Secure Router 3120
All Rights Reserved.

Nortel Secure Router CLI
Copyright (c) 1998-2006, Nortel


SR >



5. Once logged in, you can now create the admin password:



SR > password
name: admin
old password: <------Press <Enter> since no password is currently configured.
new password: <------Enter your new password.
re-enter password: <------Re-enter your new password.
password has been changed
SR >

If the system setting is not configured as indicated in solution 4099314, the configuration is lost and router is set back to factory defaults when "X" is entered at the boot prompt.
Affected Products
Secure Router 4100 Secure Router 4134 10.1
Secure Router 3100 Secure Router 3120 9.3.0
Secure Router 1000 Secure Router 1004 9.3.0
Secure Router 1000 Secure Router 1002 9.3.0
Secure Router 1000 Secure Router 1001s 9.3.0
Secure Router 1000 Secure Router 1001 9.3.0
 
If the "no system reset-to-factory" command was not issued in the initial configuration, is there any other way to recover, change, or default the password? The router I am trying to get into is set to "system reset-to-factory".
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top