Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Nortel CS1000 Integration with Ericsson 110 help needed

Status
Not open for further replies.

debussy67

Technical User
Jul 15, 2009
12
IT
hi to everyone..
I have a problem with clid in inbound calls .
The Nortel system is integrated to an Ericsson 110 through a dpnss tie line.
When somebody calls a nortel extension from outside they nortel users get as CLID the Acod of the tie line instead of the calling party number.
The Dpnns configuration on CS100 is the following can one one help? Has anyone already done an integration with an Ericsson?

CUST 0
ROUT 30

TYPE RDB
CUST 00
ROUT 20
DES DPNSS
TKTP IDA
NPID_TBL_NUM 0
SIGL DPN
CNVT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
INAC NO
SPN NO
DSEL VOD
AUTO NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 175555
TARG
CLEN 1
BILN NO
INST
TIMR EOD 13952
RMA 5120
SRM 32640
RAS 13952
NRAG 30
VSS 0
VGD 6
DRNG NO
CDR NO
NATL YES
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
TTBL 0
ACNI NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO


thanks
 
Yes we have a working setup between ericsson and cs1000 rls 4.5 using E1 connectivity. Just QSIG package is required at nortel site. We are getting CLID OK. You may check following at ericsson site

Try adc d5=0 in RODDI, Nortell don't supported Aastra UUIx.
The same with vari d2 and d3 =00 - no UUIx.
adc d25 should be set to 1 - Call back/call compl. as Generic.
adc d13 = 1 sending TCM to a Nortell ??
Another important value is AS PARNUM 223 which should be 7.

OR

on RODAI set VARC 00000350 VARI 50040000 VARO 06C000E0
on ROCAI set SERV 2110000001 SIG 511110100031

Hope this help..

 
Hi deedarshah, tghanks for your help, one question
what do you mean with adc d25 should be set to 1 -

could you send me your Roddi configuration of the ericsson you have?
the current ADC conf I have is:0505100000000250000
and the RODAP:is TYPE TL50 VARC H'00000000 VARI H'00000000 VARO H'00000000

 
question for the op.. is that an analog rdb? stateside, dtrk no, your not going to see clid.. we have clid working here across the tie.. using qsig

john poole
bellsouth business
columbia,sc
 
Hi john,
could you post your tie conf (Qsig ) for me.
do you have the ring again working through your tie line, because I am having problem on this too. This issue is nortel => Ericsson and Vice verse
 
With DPNSS your only going to get certain levels of functionaility between different vendor PABX's, if your talking about converting to QSIG then that's proably the way to go. You'll need hardware to support ie MSDL/Dchannel either Onboard DaughterBoard or 4 Port MSDLcard option and possibly your cables for connectivity

Change Device/Dch Addressing/software/config etc

Cheers!!

 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top