Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

No power to level 2 switch

Status
Not open for further replies.

007wall

Technical User
Jan 11, 2010
38
GB
thread1329-1424937
Did anyone solve this problem, I have a similar problem, no power to switch.
Error comes up MIPS not up resetting level 2
 
Is the licensing on the system?

**********************************************
What's most important is that you realise ... There is no spoon.
 
no upgrade.
The ip is correct.
Ive tried using another controller , swapping hard drives, and to see if the switch is broken, however it still doesnt have power, whereas the other drive works on both controllers??
 
Licensing?

**********************************************
What's most important is that you realise ... There is no spoon.
 
no, none of them, it has an ip address and the setting seem correct but absolutely no power to level 2 :(
 
so hard drive from another machine fires up the level 2 OK?. Your hard drive will not work on either controller? If so has to be time for a complete reinsatll or a new drive.
 
How about DBMS Save?

I seem to remember that my systems didn't have power until this step.

**********************************************
What's most important is that you realise ... There is no spoon.
 
Yes to wireman 50 it looks like it. I will have ago DBMS saving. I don't think I did that.. Thanks everyone. If this doesn't work I'm gonna have to scrap it. I haven't got the time at the moment to keep working on this.
 
Verify
The IP address of the L2 on the same subnet as the controller.
L2 ports set to ENABLES and PoE setting AUTO.
 
Log Type: Software
Log Number: 1041
Severity: Warning
Date: 2013/Jan/19
Time: 13:18:45
Source: IP Networking - MIPS
Description: MIPS not up, resetting L2 Switch subsystem...
Module: IP Networking - MIPS
File Name and Line Number: MIPSServiceProvider.cpp;803


Current Total POE Power Consumption: 9.2
Maximum POE Power Allowed: 120.0
RX timeout errors: 1
RX read errors: 0
RX other errors: 0
TX write errors: 0
Checksum errors: 9
Protocol errors: 0

pt cfg ena mode Cl Ohms mA Volts Watts Bdgt ps dny OL sht flt
-- --- --- ------ -- ------ ----- ----- ----- ----- -- --- --- --- ----
1 YES ON I-SAMP 0 26422 63.4 47.45 3.0 7.5 0 0 0 0 none
2 YES ON DISC_R 0 131070 0.0 2.27 0.0 0.0 0 0 0 0 none
3 YES ON I-SAMP 2 25132 60.4 47.51 2.8 6.5 0 0 0 0 none
4 YES ON DISC_R 0 131070 0.0 2.27 0.0 0.0 0 0 0 0 none
5 YES ON DISC_R 0 131070 0.0 2.18 0.0 0.0 0 0 0 0 none
6 YES ON DISC_R 0 131070 0.0 2.16 0.0 0.0 0 0 0 0 none
7 YES ON DISC_R 0 131070 0.0 2.21 0.0 0.0 0 0 0 0 none
8 YES ON DISC_R 0 131070 0.0 2.21 0.0 0.0 0 0 0 0 none
9 YES ON I-SAMP 2 25422 72.3 47.43 3.4 6.5 0 0 0 0 none
10 YES ON DISC_R 0 131070 0.0 2.14 0.0 0.0 0 0 0 0 none
11 YES ON DISC_R 0 131070 0.0 2.19 0.0 0.0 0 0 0 0 none
12 YES ON DISC_R 0 131070 0.0 2.37 0.0 0.0 0 0 0 0 none
13 YES ON DISC_R 0 131070 0.0 2.28 0.0 0.0 0 0 0 0 none
14 YES ON DISC_R 0 131070 0.0 2.17 0.0 0.0 0 0 0 0 none
15 YES ON DISC_R 0 131070 0.0 2.34 0.0 0.0 0 0 0 0 none
16 YES ON DISC_R 0 131070 0.0 2.26 0.0 0.0 0 0 0 0 none
----- -----
TOTAL: 9.2 20.5

*** PoE Status End ***
 
I had the same problem it was a corrupt drive reloaded software restored backup all was ok

If its not broke tweak it..
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top